M Service & Repair Forum

If you need your M tested or repaired then give us a call.
We offer fair estimates and offer extended warranties.

You can contact us at 1-(336)-969-0110
Shipping/Receiving
Industrial Electronic Repair
931-E S. Main St #204,
Kernersville, NC 27284
Phone: (336) 969-0110

We repair industrial electronic devices

If you have an industrial electronic device that needs repair,
Feel free to contact us!

— Posted by Sales on 2005-05-09

Reply🗨️Ask a New Question Below❓

If you need your M unit tested or repaired,
give us a call at 1-336-969-0110.
We offer fair estimates and extended warranties on the work performed.
Shipping/Receiving:
Industrial Electronic Repair
145 Rockwell Place Ct
Tobaccoville, NC 27050
Phone: 1-336-969-0110

Recent 256 Comments

#Miller by Troy on 2005-01-26 00:00
Miller 250303 circuit board not responding, malfunctioning under load. Need repair service ASAP to minimize downtime.
➡️ Reply
#Microdyne by KUNDAN SINGH BRIJWAL on 2005-06-18 00:00
Received alert Microdyne 1143-d a issue. Drive or board failure. Investigating now. Stand by for updates.
➡️ Reply
#Mcmartin by Donnie Ussery on 2005-09-01 20:16
Dear Rep,I have a piece of equioment that I believe is an amplifier or an attenuator. It is a part of an older paging system. The item itself is a LX-10C and is from McMartin Industries, Inc. Do you have any knowledge of this piece of equipment? If so, I would like to purchase the same model or any ...
Show More
➡️ Reply
#Mitsubishi by Negron on 2005-09-15 00:00
Hi there, I am currently assisting an employee with a malfunction on a Mitsubishi MR-J2-100A system. The issue is unclear, and we are in need of repair information to identify the problem and find a replacement part. Can you please provide us with detailed repair instructions or suggest a suitable r...
Show More
➡️ Reply
#Mutoh by Bill Jourdan on 2005-12-06 19:08
Hi, I acquired (2) old Mutoh IP530 pen plotters from about 1990 or so. Iplan on using 3 of the stepper motors and one of the drive boards for aCNC router table. I need to somehow eliminate the on-board plotter CPU.is there a way I can wire the drive board directly to my parallel porton my computer w...
Show More
➡️ Reply
#Magnavox by Frank Stadulis on 2005-12-29 16:51
I am looking for a Magnavox Micromatic (Astrosonic series) Diamond Stylus replacement. The unit is about 40 years old and I am having troubkle locating the \"snap-in\" replacement stylus. Please let me know how I can order one. Thanks Frank Stadulis(P.S. I am doing this for my Mother in la...
Show More
➡️ Reply
#Munot Engineering Ag by Juan Larrain on 2006-01-12 17:49
Hi, here at work we resived a SYS 24C Munot Engineering Ag, and we don\'t have any information about it. Coud you send us some information or datasheet if you have.best regards,JPLB
➡️ Reply
#Magna-Lock by George Roush on 2006-02-09 17:34
I have a 110VDC Magna-Lock that does not hold a part. If I unplug the lead going to the magnet base I have 130. VDC. When I plug it back in I have 64. VDC. I measure strobong resistance on the two leads going to the magnet. Is this repairable and if so do you repair them. It is powered by a transfor...
Show More
➡️ Reply
#Middex Electronic by Ian Backman on 2006-02-13 05:29
Could you please tell me if there is an agent in Australia as we have a problem with our Middex Bipolar Chopper drive (B900624).The diode (1V5KE65A) on the back on the printed circuit board has failed three times now and we would like to find the cause of the problem.Do you know what may cause the d...
Show More
➡️ Reply
#Magnavox by Angus on 2006-02-14 21:17
I\'m looking for one, too! Just bought the turntable at a local shop, but need a new stylus...--Angus.======Posted by Frank Stadulis on Thursday, December 29 2005I am looking for a Magnavox Micromatic (Astrosonic series) Diamond Stylus replacement. The unit is about 40 years old and I am having trou...
Show More
➡️ Reply
#Magnavox by Patty on 2006-04-05 07:39
I am looking for a Stylus for this Magnavox Micromatic Astrosonic, model # 100-1-RP679. All I know is that it has 4 wires that attach to it. Hope you can help.Thanks, Patty
➡️ Reply
#Mipro by Colin Veysey on 2006-05-01 09:50
I recently bought an ACT-707SE and ACT-707T, which worked great for about 30mins, then the audio disappeared with no warning, and, although the rf is still fine, I cannot get any audio signal. Could you possibly help as nothing I do seems to make any difference at all. Many thanks in advance! All th...
Show More
➡️ Reply
#Mitsubishi by MICHAEL BV. SANCHEZ on 2006-06-19 05:44
mitsubishi mc-70
➡️ Reply
#Magnet-Schultz by cruz on 2006-09-24 00:00
Hello, I am still waiting for assistance with my Magnet-Schultz CA15424-001 60MM DIGITAL GAUGE. It is urgent that someone addresses this issue
➡️ Reply
#Midex by Bill Chellberg on 2006-10-04 00:00
Repair Inquiry - Midex MX-100B STEP DRIVERDear ,I am reaching out on behalf of a client who is experiencing issues with their Midex MX-100B STEP DRIVER. Unfortunately, the exact problem is unknown at this point. The part number in question is MX-100B. Would you kindly provide information on potentia...
Show More
➡️ Reply
#Mitsubishi by hussein atrees on 2006-11-02 04:36
I HOPE THATE YOU HELP US TO SOLV THES PROPLEM IN MELSERVO MODEL MR-SA502WHEN POWER ON THE ALARM COD AL32 IS DISPLAY THANK YOU FOR YOUR SUPPORT
➡️ Reply
#Mitsubishi by sonnico elsisura on 2006-12-05 17:52
their is an error on our mitsubishi melservo-sa-r the error is alarm 52. pls reply us. thanks.
➡️ Reply
#Magnetek by Josephfug on 2006-12-27 00:00
Urgent Request for Magnetek L705 Repair InfoHi there,One of our devices, a Magnetek L705, has stopped working and we're in need of a replacement or repair. Can you please provide details on how we can get it fixed or replaced as quickly as possible? Looking forward to your
➡️ Reply
#Micro-Aide by Roland Cook on 2007-02-08 04:48
Do you have any Micro-Aide Opto Out modules part # 80-0033 that you would like to trade for Micro-Aide Opto In modules part # 80-0023??
➡️ Reply
#Magnavox by John Previty on 2007-02-19 19:10
need to replace the subject stylus the origanal factory number was 1st67-a and I have used replacement stylus radio shack RS-57(no longer avl.) and a 5603606-4 in the pastCan you help
➡️ Reply
#Macro Electronics by chistopher licda on 2007-03-27 05:51
always standby lead light,if on and off the remute control
➡️ Reply
#Mirtone by R.Jim White/WSM on 2007-05-08 23:21
Hi...I have one customer with no voltage to the door striker but have confirmed the striker works. Transformer is ok! Do you have the parts for this, relay etc to ship so I can repair it or do you have a re-conditioned unit for sale. The seniors in thecomplex want it yesterday..Can you help?R.Jim Wh...
Show More
➡️ Reply
#Micro-Aide by Ron Garcia on 2007-06-03 16:26
We have what you need!
➡️ Reply
#Milton Roy by leon pemberton on 2007-06-05 00:00
Milton Roy 301-0646-112 not dispensing chemicals properly, need assistance.
➡️ Reply
#Mitsubishi by Mehmet KARA on 2007-06-24 02:40
When I turn on the uniformity machinery, al32 alarm appears suddenly on mrh350an servo driver.Please help me. What does it mean \"al32\"
➡️ Reply
#Miller by Mike Ellison on 2007-07-10 17:30
I want to know if you have and experience with PC boards from Roboitic Interface II boards, PN 071642, 210700,180110, 171525. We have tried several different repair shops with little success an some repairs have actually damaged other boards. Thanks for you time
➡️ Reply
#Mcmartin by mike peterhans on 2007-07-28 01:12
I need a schematic or any other info available on this unit. Thanks for your help.
➡️ Reply
#Mekontrol by Robert Castillo on 2007-10-01 22:29
I have a sensor that may need to be repaired or replaced. The part # is MEK 93-RD. It is used for a shrink wrap machine. If it is possible to repair or replace, please give me a call.
➡️ Reply
#Megger Instruments by chris on 2007-10-03 16:46
HELLO SALES,I GLAD TO SEND YOU THIS EMAIL I WANT TO ORDER FROM YOUR STORE TO MY CLIENT, I WILL LIKE TO KNOW IF CAN SHIP TO USA,EUROPE,UK ? PRODUCT.DETAILS:Megger OTS60PB Automatic 60 kV Oil Test Set KINDLY GET BACK TO ME WITH THE TOTAL COST OF THE ORDER WITH SHIPPING CHARGES AND WHAT TYPE OF CREDIT ...
Show More
➡️ Reply
#Mekontrol by gray hartley on 2007-11-10 02:24
I have an need for one of these for my pallet wrap machine. HELP
➡️ Reply
#Mcmartin by TIM ELDRED on 2007-11-16 19:22
Do you have any technical data/manuals/etc. for an LT-500D amplifier?
➡️ Reply
#Monsun-Tison by SONIA ORTEGA on 2007-11-19 17:43
Good morning... I need to see if someone would be so kind as to help me determine if this product can be purchased from you... if not, would you know who I can purchase this item from... if you should have any questions, please feel free to contact me. Joystick - LEV V 732 Maker - Joystick Type 4 ax...
Show More
➡️ Reply
#Martonair by Thomas Riley on 2007-11-24 19:23
REQUEST CONNECTION CLARIFICATION FOR ABOVE COMPONENT. CON PLUG MARKED 1,2 AND 3MSD CAN YOU HELP PLEASE
➡️ Reply
#Mutoh by chriss jaquett on 2007-11-26 17:34
I have a mutoh vinyl printer....13 months old...will not print black ink...brinting other colors but they do not seem as bright
➡️ Reply
#Metramatic by John Davison on 2007-12-10 15:26
we have a metramatic weightec ser# 411782 Model # weightec LW II Which is in need of the out feed beeded chain guides part\'s 1432219 1 7and 1432219 7 these pieces are 3.25\" long would you have these parts or could you point me in the right direction to get these parts thank-you
➡️ Reply
#Mitsubishi by Leopoldo Gonzalez on 2008-01-07 22:02
Dear sirs. I have a Brake press Amada HFB 8025, I need a servo amplifier Melservo Mitsubishi MR-SO 403N
➡️ Reply
#Mitsubishi by Phanom on 2008-01-31 09:13
I HOPE THATE YOU HELP US TO SOLV THES PROPLEM IN MELSERVO MODEL MR-SA502WHEN POWER ON THE ALARM COD AL24 IS DISPLAY THANK YOU FOR YOUR SUPPORT
➡️ Reply
#Mirtone by darren kotzur on 2008-02-16 00:00
Mir-tone Assy. 72024100 motherboard not powering up, no lights or display. Need repair service ASAP.
➡️ Reply
#Mirtone by Barry Kater on 2008-02-19 00:23
I am repairing a door lock at an apartment block showing these symptoms.A transformer feeding the MA-485 is outputting 19.25 volts...will this harm the unit.It is a 16 volt amplifier.B when an apartment station depresses the door button the output at the amplifier terminals for the ac door reads 19....
Show More
➡️ Reply
#Monsun-Tison by Tommy Karlsson on 2008-03-03 07:26
I have a Monsun-Tison Joystick.ICM425-0163 VSK 13825 and I need a new knob.Do you know were to find parts for this one.
➡️ Reply
#Metronix by Jimmy Ng on 2008-03-04 13:08
Can you do repair METRONIX Servo Controller Model: ARS 310/5.Please quote also.RegardsJimmy Ng
➡️ Reply
#Martonair by Johnny Almeida on 2008-03-11 17:28
CAN YOU TEST AND REPAIR (IF NEEDED) OUR MARTONAIR SOLENOID VALVES PN M/1761/152/10? HOW MUCH DO YOU NORMALLY CHARGE AND HOW DOES IT TAKE TO REPAIR IT? DO YOU GIVE A WARRANTY FOR THE PARTS YOU REPAIR?
➡️ Reply
#Martonair by Jill Bryant on 2008-03-17 21:20
I have a Martonair part, model M/21D/70 and I was told it needs to be fixed in order to work. Is this a part you carry?
➡️ Reply
#Mitsubishi by Hitoshi Sugi on 2008-05-06 06:05
Dear sir.We are manufacturing the electrical machinery and apparatus in Japan.Our customer is using Mitsubishi Melservo MR-SA 202U.But Alarm code 24 indicated on the display of that one.The servomotor did not move. Please estimate it for repair if it is possible. Products .....Mitsubishi AC servo MR...
Show More
➡️ Reply
#Mitsubishi by Manuel Jimenez Garcia on 2008-05-15 02:17
their is an error on our mitsubishi melservo-sa-r the error is alarm 52. pls reply us. thanks.
➡️ Reply
#Martin-Decker by Larry T. Brooks on 2008-06-02 12:39
To Whom it may concern,I am working for Chevron and we are tiring to gather some inform by monitoring \"real time\" the anchor tensions of the barge we have moored to our deepwater platform here in Indonesia. We have installed some Electronic Memory Pressure Gauges to the Martin Decker lin...
Show More
➡️ Reply
#Mutoh by steven kopel on 2008-06-07 16:22
printed 6mil wall vinyll job approx 100\'.....in 5\' panels..when tryie to cut media to change roll to reg media,,the cutter stopped in the middle,,,,and i turned off machine and cut manually---when i went to reload i got fashin lights on panel and error code Y74had a computer tech hougholy clean th...
Show More
➡️ Reply
#Modex Automation by waqar Ali Khan on 2008-06-18 20:43
I have BC700 series constant current battery charger Part Number: BC700/12LASupply votrage: 230/110 VAC, 50/60 Hz.Nominal output: 3AFor use with battery type: 12V lead acidI want complete circuit diagram of the above charger as the same is gone faulty and needs repairing.
➡️ Reply
#Mirtone by Bruce Aronson on 2008-06-25 04:22
Mirtone now owned by GE and system is 20+ years old - No manuals or hookup diagram left - please help
➡️ Reply
#Martonair by Queena Chu on 2008-07-04 02:36
Dear Sir, This is our pleasure to write this inquiry to you. Our company is named AdvanTech. We are an experienced trader in the industry for such a long time. We have heard about your product and we need.Please quote for the following items with their lead time and weights: Maker: MARTONAIRMODEL: 1...
Show More
➡️ Reply
#Magnavox by anita proctor on 2008-07-10 14:48
stylus need replacing and stylus retainer slot . Stylus mounting spring a;so might need replacing.
➡️ Reply
#Magnavox by anita proctor on 2008-07-10 14:51
stylus need replacing and stylus retainer slot . Stylus mounting spring a;so might need replacing.what are these prices for paarts
➡️ Reply
#Modex Automation by ROLLY on 2008-07-30 09:06
HELLOPLEASE QUOTE CIF MANILA, PHILIPPINES8 UNITS BUILT-IN CHARGERBC700 SERIES CONSTANT CURRENT CHARGERGBRAND: MODEX AUTOMATIONPART NO.: BC700/12LASUPPLY VOLTAGE: 230/110VAC, 50/60HZNOMINAL OUTPUT: 3AFOR USE BATTERY TYPE: 12V LEAD ACIDPURPOSE:FOR REPLACEMENT OF DEFECTIVE BUILT-IN CHARGER OF GENSETTHA...
Show More
➡️ Reply
#Mirtone by andré desjardins on 2008-08-06 21:37
hello we did renovation and we broke a wire now we need the sqematic for it thank you
➡️ Reply
#Magnavox by Jim Larsen on 2008-08-08 01:31
My wife and I purchased a Magnavox micromatic high fidelity stereo counsel in 1963 that needs repair service.Your suggestions or help will be appreciated.Jim Larsenjimwestusa@aol.com
➡️ Reply
#Mipro by Joe Birdo on 2008-08-24 03:56
I have a ACT=707SE unit. whenever I use my wireless mic with this unit, and whenever I am more than 5 feet from the receiver, I get dropouts really bad. and sometimes I can be less than 5 feet from the receiver and have the transmitter on the other side of my body and it will not have a signal. The ...
Show More
➡️ Reply
#Magnavox by Candi on 2008-09-07 00:25
I just bought a Magnavox at an estate sale and love the sound!!Can\'t find info. on this model, might you know what year it is?I will have to replace the stylus. Will I have to remove the whole arm to reinstall the stylus?Also, when i turn the volume up the speakers don\'t sound right, as if the rad...
Show More
➡️ Reply
#Martonair by Ms. Sarita on 2008-09-15 13:01
Dear Sir,Please advise cost and availability for the following:-Sliding Gate Valve Solenoid Valve(Assembly)Maker: MARTONAIRType: M/201528/172/DBar: 2.5...10 barQty: 5We would appreciate your response in this matter.Best RegardsMs. SaritaGlobetech Services Ltd.
➡️ Reply
#Martonair by Ahmed Abdelfatah on 2008-09-22 08:28
CYLINDER THM/1031/300Martonair
➡️ Reply
#Magnavox by phil on 2008-11-03 23:10
hello, i have a magnavox Hi-Fi record player model TP246-D,probably from the 50s early 60s. looks like a suitcase, i want to replace the stylus, its removed by a thumb screw and it has both needles next to each other, the needle # are believed to be.Diamond tip .001 and safire tip .003 i think the p...
Show More
➡️ Reply
#Mge Ups Systems by Juan Mancarella on 2008-11-04 02:01
We are tried to find the following capacitor. BHC Aerovox4400 uF +or- 20%500 VDCMAX TEMP 60 grade CALS31C 1030 RPU.K.MADE 9928 This capacitor is part of one UPS Merlin Gerin that we have in Venezuela. Two Aerovox capacitors exploited and burn part of the UPS. We need the capacitors to repair the UPS...
Show More
➡️ Reply
#Matsushita by allie on 2008-11-05 05:56
i have a blood pressure monitor that was designed by matsushita and it needs repairs. could you please e mail me the contact details of matsushita in South Africa.your co-operation is highly appreciated
➡️ Reply
#Metramatic by don coury on 2008-11-22 05:12
Have a couple questions in changing from a four line system to a two line system. I have pictures but theres no way of sending can\'t find your email. If there is any way I could talk to someone familiar with this unit I\'d appreciate it. Sincerely, Don Coury
➡️ Reply
#Mcquay by Irene Gutierrez on 2008-11-22 19:07
I am looking for the quantity of filters in a 1991 35 Ton McQuay Model # CUR351E 20X25X2 & A 1991 25 Ton McQuay Model # CUR100F 16X25X2 I really would appricate your help.Thank you Irene GutierrezAnderson Air Conditioning (714) 998-6850
➡️ Reply
#Magnavox by Robbye Binkley on 2008-11-24 16:01
Looking for a needle for my old Magnavox Solid - State Stereo High Fidelity Astrosonic Series
➡️ Reply
#Mutoh by Najib Assegaf on 2008-11-28 06:15
Dear Mutohi have problem with my digital printing machine which is mutoh Rockhopper II/87\" model RJ-8000-87k-SDMP, serial no D08K:00029 since one month ago. and have repair by Mutoh Indonesia Authorized (PT ASABA) but no result and solution from PT ASABA.cronolgy :1.PT ASABA judge my mainboard...
Show More
➡️ Reply
#Magnavox by Steve Martin on 2008-11-29 02:23
I have a magnavox cabinet stereo that was apparently damaged in some fashion by two children. It worked well just 2 days ago. The model number is 3CP605. I removed the stylus and it\'s a disaster. Do you have any suggestion? The cabinet is really too big to ship.
➡️ Reply
#Martonair by marco tinoco on 2008-12-05 14:40
DEAR SIR:I AM LOOKING FOR THE FOLLOWING:- 02 EA TIMER MARTONAIR MANUFACTURER P/N: M/50922 RANGE: 10-100 SEG.DO YUO HAVE THIS PRODUCTS? COULD YOU QUOTE US?BEST REGARDS.MARCO TINOCOALLIED SERVICE INTERNATIONAL INCT: 786 347 6015F: 786 245 4549
➡️ Reply
#Moore by Souza on 2008-12-28 00:00
The Moore 15945-11-6 unit is not working.
➡️ Reply
#Marsh Bellofram by POT on 2009-01-04 04:27
I am seeking repair service for my Marsh Bellofram T-3000 SPCJR-0E10-0G060 transducer. The unit is supposed to convert electrical signals into precise pneumatic outputs for process control applications. However, it is currently failing to provide consistent output pressure, leading to erratic perfor...
Show More
➡️ Reply
#Mcmartin by Jerry Nelsen on 2009-01-16 15:53
would happen to have or know of anyone that has a schematic or diagram of a McMartin MT-4 and MT-6 transformers. Any help would be appreciated. Thanks, Jerry
➡️ Reply
#Mirtone by tim stokolosa on 2009-01-17 14:06
My customer has an 8 floor.20 suite/floor mirtone system with pull stations in all suites.each suite is decoded in the mirtone on each floor and then on the first and second floor there are two master stations to decode the floor number. The system is only local to the caretaker.The owners want all ...
Show More
➡️ Reply
#Melco by Mark Howell on 2009-01-19 22:40
I have a Melco Emt 10-4T and apparently had a power surge. It seems to have burned up some boards, at least some components. I replaced the power supply because I could see one component fried. Still can\'t get the machine to work. It will display e-stop engaged. I have disconnected the emergency st...
Show More
➡️ Reply
#Magnavox by VIRGINIA SERN on 2009-02-11 16:10
I have a Magnavox Micromatic photograph player. It is in a consul that also has a radio.The photograph plays all three speeds. Unfortunately, the needle is missing and I need a new needle.I cannot find any directions or how to replace the needle nor the number for the needle. Can you help me so that...
Show More
➡️ Reply
#Mikropul Corp by Tom Porter on 2009-02-17 00:00
Experiencing issues with the IC Timer on the MikroPul Corp 72 132596 unit. Looking for a repair specialist to address the malfunction
➡️ Reply
#Modex Automation by HASSAN BIN ARSHAD on 2009-03-02 12:40
Dear sir,i hv a few faulty units, if the unit can be repaired pls quote me the cost inclusive of courier charges and related cost, and also quote me the new unit price inclusive of other charges.ThksBregardsHassan
➡️ Reply
#Martonair by Daniel Mircea on 2009-03-16 09:23
I\'m interested how I can procure following Martonair parts :ME/20013/9ME/20013/23ME/20013/25ME/20013/27ME/20013/29...all these parts are Disc Springs!
➡️ Reply
#Motion Science by Luis Przybylski on 2009-03-23 13:25
Dear Sirs: I ahve a Quad machine with a motion scince stepping motor driver board MFSX16006-01. It is not working. I need to know if you can repair (or sell a new one) and the cost of the service (or the new board).Thanks in advance for your attention and co operation.Best regards.Luis Przybylski
➡️ Reply
#Martonair by Garry Liles on 2009-04-02 14:08
I\' am Looking for a repair kit for a Martonair # M/1742E/152 VALVE
➡️ Reply
#Martin-Decker by reginald aguilar on 2009-04-15 02:26
I would like to request for quotation on the ff: ITEM NUMBERITEM DESCRIPTION QUANTITY1FLUID; MARTIN DECKER, WHITE COLOR PN-W-8 162FLUID; MARTIN DECKER, RED COLOR PN-W-15 32ITEM NUMBERITEM DESCRIPTION QUANTITY1GENERATOR; TACHOMETER PN-H-136-1A 9 PCS2CYLINDER ASSY PN-P65A-1 3 PCSEND USE: FOR MARTIN DE...
Show More
➡️ Reply
#Magnavox by Gary Johnson on 2009-05-04 19:49
HII have a 1963 Portable Magnavox suitcase style stereo & I know it needs a little work for the speakers. I believe it would be a loose wire or something like that but if I try to fix it, it will be no longer any good, I\'m not good at fixing things.I was wondering if you had the schematic for t...
Show More
➡️ Reply
#Mitsubishi by SUBBARAYULU.K on 2009-05-06 07:17
ALARM : AL20 GIVEN after 3 to 4 operations.servo drive model no:MR-J2S-70A
➡️ Reply
#Mirtone by Rick Burdge on 2009-05-07 17:57
looking for a unitsystem is in an apartment complex. tenant can operate one entrance and hear from same however 2nd entrance does not work
➡️ Reply
#Magnavox by Casey on 2009-05-08 00:15
need info on magnavox stylusmodel-4st640serial-2475937responde appricated asap. Thank you.
➡️ Reply
#Mirtone by Christiane Larouche on 2009-05-17 13:44
please send manual mirtone ec200 but tone stop laps time small please send me why do it the time = laps time long.ThanksJ\'aimerais savoir comment faire pour mettre le signal sonore sans interruption automatique. C\'est à dire que je veux l\'arrêter moi-même. Merci
➡️ Reply
#Monsun-Tison by lloyd kerr on 2009-05-26 16:48
looking for 4 pc of a 24volt coil p/n 9126-3235for a monsun tieson valve hv090791004
➡️ Reply
#Mitsubishi by archie reyes on 2009-05-31 15:23
we have servo amplifier j2s 350 but we have no servo motor so can u help pls. and also ask the alarm 16 how to reset thank you and God bless you
➡️ Reply
#Mutoh by Rick Blankenship on 2009-07-16 16:39
Printer will not print yellow or magenta
➡️ Reply
#Mitsubishi by R.Baskaran on 2009-08-19 19:31
Dear Sir, In MR-J2S-70A servo drivedisplay showing AL - - ,Kindly help us to solve this problemRegardsR.Baskaran
➡️ Reply
#Mapnet by vardhan on 2009-08-21 00:00
Urgent Request for Repair/Replacement Info on Mapnet 565-007Hi ,One of our Mapnet 565-007 units has stopped working, but we can't identify the issue. We need immediate assistance in determining if a repair is possible or if a replacement is available. Could you please provide us with repair/replacem...
Show More
➡️ Reply
#Magnavox by Shelley Brown on 2009-09-04 22:03
was just wondering what year , and what it is worth, if anything,,, thanks for your time
➡️ Reply
#Martonair by andre aleong on 2009-09-29 14:10
need to know if part can be fixed, or if replacement available
➡️ Reply
#Magnavox by Shauna Way on 2009-10-11 04:56
I have a Magnavox 32MF231D/37, the other day went into the room the screen was black like the tv was off, there was no sound but the green led light was on. I am unable to shut the tv power off with remote or by hand, I have tried unpluging. But still same result, Black creen and no sound, LED stays...
Show More
➡️ Reply
#Mutoh by sureeporn on 2009-11-18 11:01
HelloDo you have 5515 1D06D04 IC? It on power supply (connect with mainbroad).Thank yousureepornmalisoan@hotmail.com
➡️ Reply
#Mutoh by lionel chin on 2009-12-01 04:10
i need a new main board
➡️ Reply
#Milltronics by Ted Romaine on 2009-12-22 00:00
Hi there, do you have repair info available for a Milltronics 7ML10041AA101BB NAKED VGA LCD display assembly? Something is not working and we need a quick solution. Thanks!
➡️ Reply
#Mirtone by selina drake hohn on 2009-12-24 13:59
Hello, I am trying to obtain a manuel for the mirtone 7800 series fire alarm system. I can\'t seem to locate one. Could you direct me to where i can either down load one or purchase one? Thank you,Selina
➡️ Reply
#Mirtone by nelson dominguez on 2010-01-13 15:59
I require of support and that contacts a distributor to me of mirtone in the city of Mexico thanks
➡️ Reply
#Mutoh by abdul samad on 2010-02-12 17:07
we required repaing the main baord de-21721b reparing for mutoh rj8000 printer , also tell me new main baord price and used main baord price, and avlibelty. thanks
➡️ Reply
#Mcmartin by scott sutton on 2010-02-27 21:25
do you have a spec sheet for these amps...i just acquired 2 of themthanks
➡️ Reply
#Martonair by Todd Simmons on 2010-03-02 18:06
Need rebuilt or brand new valve for replacement of old
➡️ Reply
#Mutoh by william shava on 2010-03-15 11:51
needs to know more about these mutoh printers
➡️ Reply
#Mutoh by Quintin King on 2010-04-01 23:00
Printer has be out of service for over a year. I need to get the lines flushed and the heads cleaned and adjusted. If you can help let me know.
➡️ Reply
#Mutoh by sandro on 2010-04-18 23:05
cr overcurent
➡️ Reply
#Mge Ups Systems by braveboy on 2010-04-21 10:24
dear sir,Need ur help,I have mge 780va MGE esv8+ ups ,,,fault beeping ,,i already check battery its ok ..i think its controller fail pls tell me how find its controller number regards,bb
➡️ Reply
#Mutoh by Usman Khan on 2010-04-28 12:00
Hello,We can provide used mainboard.kindly specify printer width.
➡️ Reply
#Mutoh by Ben Beaird on 2010-04-30 17:37
Mutoh falcon outdoor Mainboard? Roland gx-24 Mainboard
➡️ Reply
#M-Tek by Joe Kammers on 2010-05-12 12:41
Good Morning. We are a used industrial food processing equipment company, and send in an average of 10-15 heads for refurbishment and repair. Do you guys pour epoxy on the chute? Can you completely rebuild? Thanks and would like to talk.
➡️ Reply
#Mitsubishi Okk Hm40 by DAN on 2010-05-15 15:45
: Our industrial unit, a large-scale packaging facility, has been experiencing a consistent issue with the conveyor system. The belt constantly breaks down, causing significant delays in product packaging and resulting in lost revenue. This leads to increased labor costs as we're forced to manually ...
Show More
➡️ Reply
#Martin-Decker by Eylem ULAS on 2010-06-03 08:54
Could you please quote 100 pieces of below instrumentFluid,Gage-case freeze point-F6F(-60C)Flash point +161F ( +72) specific gravity.780In one - Litre Cont. P/N: W-8thanks in advance and kind regards,
➡️ Reply
#Mirtone by Dan - North Coast Refrigeration & Electric, Inc on 2010-07-12 18:14
We have a mirtone EC200 installed in a 36 unit Sr. Care complex with standard call switches in each unit and a call light outside the entry door on the exterior of each unit. The system is powered with a 24VAC transformer. We would like to replace the outdoor lights with a Horn/Strobe combination un...
Show More
➡️ Reply
#Martin-Decker by Abu Faiz on 2010-07-14 15:30
Dear Sir,We require MARTIN DECKER WEIGHT INDICATOR. In which E- mail address shall we send our inquiry. We are in Dammam, Saudi Arabia.Waiting for your earliest reply.Thanks and Best RegardsAbu Faiz
➡️ Reply
#Muller Martini by Joseph Blavatt on 2010-07-22 11:08
Could you email me anything about the 4182.7024.3G printed circuit board module. I would like to know what the signal pin outs would be for the various connectors. Things like correct input voltage, communications requirements, etc. Anything you can email me will be appreciated....Joe
➡️ Reply
#Mutoh by A. Rezaei on 2010-07-28 14:54
I have a mainboard with the serial no. DE-21721B and I want to replace it by the old one in a Mutoh Spitfire 90. But I\'m not sure that it matches the machine. Can you help me please?In addition, can you repair that kind of mainboard? And if yes what is the price and how long does it take? In fact, ...
Show More
➡️ Reply
#Monsun-Tison by Shin, In Cheol on 2010-08-18 03:51
Dear sir,We are pleased to contact your company.We are going to the Monsun-Tison Joy-Sticks as below.* ICM421-0121 GRYIf you can, please let us know the price asap.Thanks and best regards,Ice Shin
➡️ Reply
#Magnavox by loren stevens on 2010-08-18 14:58
I have a Magnavox, Micromatic stero turn table in a case. The vintage of this unit, is circa 1970.I am nearly certain, that the wireing in the arm, is where the trouble is.Otherwise this turntable works fine. It\'s in a cabnet, so not easily transported.Any known repair person in this area would be ...
Show More
➡️ Reply
#Magnavox by Al Price on 2010-08-21 00:09
I am requesting your services in finding a repair shop who can repair a 1966 Magnavox Astro Sonic Stereo.The problem the turn table want turn and it make this loud noiseThank you
➡️ Reply
#Micafil by eugene cargullo on 2010-09-03 03:02
SpecificationsBrand: MICAFILTYPE: VACUUM OIL FILTERMODEL: VOT30ORDER NO: 84013293YEAR OF MANUFACTURE: 2004S/N: HL 9901287Pls. send me your product manual for us to optimize its use. Thanks and more power.
➡️ Reply
#Mutoh by Bob on 2010-09-10 00:39
I was recently having my Mutoh printer transported when it tipped over in the truck and it slammed down directly on the ink cartridge slot assembly. The ink cartridges were jammed into the machine breaking all the slot mechanisms and snapping off the plastic ink ports at the couplers feeding the met...
Show More
➡️ Reply
#Mitsubishi by Jorge Coelho on 2010-09-18 15:20
have you a schematic diagram of this unit?have you some information to help us to fix this problem?Thank you
➡️ Reply
#Magnavox by Frank Dailey on 2010-09-20 19:51
I have a 1960 magnavox console in great condition it was my dad\'s. It however does not have a cartridge or styllist, the wires are hanging in the arm do you know there I can get a replacement. Stylist number 591062-1, model 1ST232-L purchased Dec 1960.Thank You
➡️ Reply
#Mitsubishi by Bruno Neto on 2010-10-18 09:10
I\'m having a trouble with a MR-J2S-70A (Servo Amplifier)It\'s returning the alarm 37 and i don\'t use the regenarative brake and the parameters are well definided for that...The alarms is still there and i\'d like to know if there is anyway to fix it...Thanks for all the information that you can gi...
Show More
➡️ Reply
#Mitsubishi by tommyhung on 2010-10-30 18:10
my melservo MR-J2S-70A problem, alarm AL.10.please give me know cause why? thanks
➡️ Reply
#Mutoh by John Bodden on 2010-11-07 03:08
I am having power issues with my Mutoh VJ-1204 printer.I sent a print to the machine yesterday which caused the printer to failed mysteriously with an error code in the display, however I was unable to capture the error code displayed before cycling the machine. I cycled the machine and now only the...
Show More
➡️ Reply
#Martonair by Jerry Hiatt on 2010-11-18 01:30
I am looking for a repair kit for a : Martonair, SPG/93230/100K air cyclinder.Thanks for any help or information.
➡️ Reply
#Mge Ups Systems by M. KASHIF on 2010-11-22 10:30
Dear SirWe want to repair our following UPS:MERLIN GERIN UPS 200kVa galaxy NT03 Serial no. UQGA25002ARTICAL 6740707Waiting for your positive reply.Best Regards,M. KASHIF
➡️ Reply
#Magna-Lock by Fred Ambli on 2010-11-29 14:53
We have a Magna lock HR510 S/N 346 this unit keeps blowing fuses.Can you repair this for us???
➡️ Reply
#Mitsubishi by SYED TALHA ANSAR on 2011-01-09 16:48
DEAR SIR I AM USING MR-J2S-10A BUT SOME OF MY DERIVES R INDICATING AL-E9I HAVE REPLACED ITS POWER MODULE BUT THE PROBLEM IS STILL THEREWILL U PLZ GUIDE METHANX
➡️ Reply
#Mutoh by Steve Arslan on 2011-02-10 01:26
Do you repair or sell headboard for mutoh falcon rj6100?Thank you
➡️ Reply
#Mitsubishi by Mukesh Rawat on 2011-02-16 07:56
Dear sir,I want the specification of this battery(MR-BAT)so please send me early.Need to replace this battery.Thanks Mukesh Rawat
➡️ Reply
#Mirtone by Dennis Hoard on 2011-03-20 22:58
Mircom Intercom Amplifer -MA-485 \"do,s not have any audio sound aplification needed to operate an apartment intercom station . I beleive when the oringinal split transformer 8v for door and 16 vac for the audio burned out\" because the pos+ side came lose and grounded to the neg - side th...
Show More
➡️ Reply
#Martin-Decker by Maryono on 2011-03-28 05:41
Dear Sir,I am looking for Instrument Fluid WF100,WF102, which I am believed Martin Decker have this product. I am base in Muscat, Oman. Pls , advise and waiting your good reply.Regards,MARYONO
➡️ Reply
#Monsuntison by Ralph Nutzman on 2011-03-31 00:00
Pilot control valves on my Monsun-Tison At-68906 not responding properly. Need immediate repair assistance.
➡️ Reply
#Mitsubishi by Tim Van Bruggen on 2011-04-05 14:05
I have a Mitsubishi lathe model M-TC8A serial TC8A-005. I believe one of the soft keys on the controll is sticking. I have removed both the small board and large board and cannot find anything wrong with them. I am pretty sure that one is sticking because I can here the beep and all my lights flash ...
Show More
➡️ Reply
#Mutoh by upendran.sd on 2011-04-23 18:25
I have a mutoh vinyl printer... but the printer not print black ink and the print start time the media coming loos in front and that time the printer screen showing \"pf motor error\"
➡️ Reply
#Monsun-Tison by Bill Beaty on 2011-05-03 02:25
Hi,I have a monsun tison PCL 401-664 920 joystick and I need a schematic diagram. Do you know where I can find one?Thanks,Bill
➡️ Reply
#Monsun-Tison by Bill Beaty on 2011-05-03 02:26
Hi,I have a monsun tison PCL 401-664 920 joystick and I need a schematic diagram. Do you know where I can find one?Thanks,Bill
➡️ Reply
#Martonair by Patrick Chikuka on 2011-06-09 08:05
1.)complete 4way valve solenoid /pilot operated valve p/n b/4sp/122/k voltage 110 dc, maker:Martonair. QTY:102.)complete. 4 way solenoid /pilot operated valve p/n b/4sp/122/k voltage:220dc maker: martonair. QTY:103.)complete. 4way pilot operated valve p/n b/4pt/40/n. maker: martonair. QTY:10 4.)comp...
Show More
➡️ Reply
#Martin-Decker by AKMAL on 2011-07-01 02:03
I would like to request for quotation on the ff:ITEM NUMBER ITEM DESCRIPTION QUANTITY1 FLUID; MARTIN DECKER, W15 (50 DRUMS)2 FLUID; MARTIN DECKER, W8 (20 DRUMS)END USE: FOR MARTIN DECKER INSTRUMENTPlease send your quotation together with the following:1. Your official Quotation that will include the...
Show More
➡️ Reply
#Markem by RAY GRAJEDA on 2011-07-18 19:26
We currently have a U-1479L unit in which the Laser PC hard drive has died. Is this somthing you can repair.Thanks Ray
➡️ Reply
#Minarik by Ian on 2011-07-22 00:00
Do you have a Minarik rg310ua available for sale or repair? Production is down and we need a replacement urgently.
➡️ Reply
#Mitsubishi by Marginean Marius on 2011-08-02 09:08
Dear Sirs, Please help us with an error code that we have on this driver MDS-B-SP-260, from a MAZAK CNC Lathe QT-200.On the display of the driver we have F6 - 36 error code, and on the machine driver malfunction.Thank you and we are waiting for your reply,Best regards,Marginean Marius
➡️ Reply
#Martonair by LEE SANG HUN on 2011-08-16 09:56
martonair M/1764A/125-220V solenoid valve is in use will want to purchase this product standards and specifications, please contact the e-mail you want to know.
➡️ Reply
#Modex Automation by JESUS GALLEGOS on 2011-08-20 03:03
Please, quote me your best price, conditions and time of delivery for:1 pce. Battery charger 12VCD 127VCA BC512127FR BC700 series constant current charger Part Number: BC700/12LA Suply Voltage: 230/110 VAC, 50/60 Hz Nominal Output: 3 A. For use with batery: 12 V lead acid. Modex Automation.Thank you...
Show More
➡️ Reply
#Mitsubishi by jay on 2011-08-30 15:28
the error you have is a F6 3b and it means that the unit has over heated, you can power down for 20 min and it may clear its self if not you may need a new drive als make sure the cooling fan on the side is running
➡️ Reply
#Mutoh by Troy Walker on 2011-09-17 01:49
need my falcon out door jr. repaired
➡️ Reply
#Martin-Decker by Ramadan Beshir on 2011-09-20 14:07
Dear Sir,I am woking with Iraq Drilling Company, I am facing problem of instrument readings as it differs between day and night also between inter and summer time as the climate here differs dramatically therefore I am looking for good type of oil that can stand this climate.Would you please advice ...
Show More
➡️ Reply
#Melco by vicki palonen on 2011-09-28 02:51
i have a emt 10t phase 2 it just died i feel it must be the power supply no lights nothing do u repair power supplys i checked with melco and they will replace it new for 1200 or rebuilt for a 1000 i would love to have other options its a great machine i bought it new in 98 i really need to get it w...
Show More
➡️ Reply
#Macro Electronics by James Rolf on 2011-10-10 21:49
Hello,I am looking for some information on replacing dimmer switches for our hotel’s ballroom chandeliers. What I was able to find on the old switch is “Noble B50Ka 0037”, “C&K USA”, and “Macro.”Please let me know if there is any additional information that I can provide for you to locate this e...
Show More
➡️ Reply
#Mitsubishi by Sunil Shivatare on 2011-11-09 14:09
Dear Sir .We have a cnc sliding head machine on which the mitsubishi - AC Servo MELSERVO-SA is fitted for turret application .Macvhine has been recently imported .While installation we r facing problem on the above drive .Intially alarm AL32 over current alarm was coming ,so we tried to check the mo...
Show More
➡️ Reply
#Martonair by adele on 2011-11-14 06:49
price & delivery on the following please:6 only mortonair solenoid valves part number um/22354b/6123/ms/13j
➡️ Reply
#Manifold Industries by Jose Corona on 2011-12-02 15:24
To be concern it:I want to get quotation of these 1 pc catalogue Sapre parts1 pc Scheme electric1 pc Scheme neumatic1 pc Scheme hidraulic1 pc Working production catalogue for machine RTU -500 size -OSC, serie V24864. Trade mark Manifold Indexing, MANIFOLD INDUSTRIES LTDI have one telephone number bu...
Show More
➡️ Reply
#Mutoh by truprint on 2011-12-17 01:20
Hello,I need some help.My valuejet 1204have this mesage and beep sound:\"E085Err Head Heat\"can not print, What I have to do?
➡️ Reply
#Miller by Andrew Clyde on 2012-01-19 03:17
I am wanting a quote to repair a 136-494 control board.
➡️ Reply
#Movomatic by Nordmann on 2012-02-22 12:56
Hello,we have a EM 261/A sensor but we have no manual of this sensor.Is it possible to send us a manual of this sensor?best regardsRene MüllerNordmann GmbH & Co.KGGermany
➡️ Reply
#Minimotor Sa by naiyi wang on 2012-02-27 23:44
minimotor SAswiss made,14/1 134:1K179981731 278and981730 278for HITACHI SEM stage drive, one of the motor mag get burnt due to lines shorting.Please send me a quote and turn around time.
➡️ Reply
#Mutoh by SIGN AMERICA on 2012-03-02 23:46
SIR\'WE HAVE PRINTING ISSUE.
➡️ Reply
#Mutoh by SIGN AMERICA on 2012-03-02 23:48
SIR\'WE HAVE PRINTING ISSUE. PHONE NUMBER;1- 773- 262- 7800
➡️ Reply
#Modex Automation by INOCENCIO RIVERA ISLAS on 2012-03-03 01:10
COTIZAR CARGADOR DE CORRIENTE CONSTANTE BC700/12LA MODEX AUTOMATION. EN MEXICO DONDE PUEDO COMPRAR ESTE EQUIPO?.SALUDOS.
➡️ Reply
#Martin-Decker by Rsfael on 2012-03-15 08:15
Saipem operates in Angola, and i work for this company.We use your products, bur we are required by law in Angola to have them in portuguese. fluids like W15.Please could you provide them?
➡️ Reply
#Mutoh by Jason Brodie on 2012-04-09 01:33
Hello,I was wondering if you have a used mother board for a Falcon Outdoor 62\"?Thanks,Jason
➡️ Reply
#Marconi by Ratchanee Poonlarp on 2012-05-22 19:58
EQUIPMENT TO REPAIR, PLEASE QUOTE US ASAP.1. Marconi 131-9835/04 CONTROLLER CARD (KX60A)Firmware Version: S38-0710/04.04.10Product Type: Marconi MD202 1, qty 2. Marconi 131-9754/02 2XSTM1 COMMON PART CARD (KX61G)Firmware Version: S38-0701/01.04.15Product Type: Marconi MD202 1, qty 3. Alcatel 3AL8660...
Show More
➡️ Reply
#Marconi by Salam on 2012-06-14 07:31
Hi,Can I get a quotation to repair/maintenance 2000 units of MAT6D ? Not all units are faulty. We just want to make sure that the thing is working.Thank you.
➡️ Reply
#Mutoh by Rich Pogue on 2012-06-20 17:17
We recently installed a new print head on our Mutoh Valujet 1304 and I think the tech shorted out the network port on the motherboard (nothing I can prove). I can get it to print test prints but it will not communicate with my computer so I can\'t send files to it to print using the original motherb...
Show More
➡️ Reply
#Martin-Decker by Edwin Lau on 2012-06-27 03:09
Hi There,Please quote us as per below- 1 COIL 3MM DIA X 380FT (7x17) LHLL GALVANIZE STEEL WIRE ROPE FOR MARTIN DECKER RG252-1Thank you.Best Regards,Edwin Lau
➡️ Reply
#Movomatic by Dev Mawee on 2012-07-05 14:40
We require a 261A sensor, could you please quote us a price & delivery. Regards, Dev Mawee
➡️ Reply
#Machinemate by Christy Rowan on 2012-08-21 18:46
I have a question on a Machinemate control that I\'m working on. We finished a retrofit on a mill about 6 years ago, and the machine has been working fine. But recently the probe function stopped working and the next day they had trouble booting up the machine. They had called a technician in, and h...
Show More
➡️ Reply
#Monsun-Tison by Francis Cammas on 2012-09-13 15:09
Our Koehring 1466 use Monsun Tison joysticks # HVP03-3220.Need to know where I may buy some of them to relpace the ones on machine.Thanks,Francis CammasEquipment yard superintendent.
➡️ Reply
#Mmats by Mortazavi on 2012-11-26 00:00
Could you please confirm if you have another Mmats we4-3 oc available for sale or repair? The unit in use has stopped working and we need to keep production running. Thank you.
➡️ Reply
#Marshall by ma on 2012-12-30 00:00
Machine Operator Report Marshall Electronics 101362 not powering on.
➡️ Reply
#Mirtone by Graficas Dimensión on 2013-02-13 00:00
Can the Mirtone 79044 board be repaired or bought? I'm trying to check this off my to-do list.
➡️ Reply
#Mirtone by Robert on 2013-06-13 18:11
No power being supplied to the door lock. Unit is clicking when door release pressed but no power being supplies to door lock. Anyone have an answer or solution for this ?
➡️ Reply
#Motion Science Inc by mohammed gomaa on 2013-07-22 04:26
I am reaching out regarding my Motion Science Inc. 1942969 unit's Auxilliary Bob Board. The unit is not functioning properly, as it does not power on and is displaying error messages on the screen. I have tried troubleshooting steps like checking the connections, but the issue persists. Based on the...
Show More
➡️ Reply
#Marconi by Harris Arbouniotis on 2013-07-22 09:32
Could you please inform me if you can repair the following unit?131-9835/04 AAA 010best regards
➡️ Reply
#Marconi by Lazaros Papazoglou on 2013-10-11 10:42
Hello I was wondering if you will be able to repair 5 of 131–9835/04 Marconi/Ericsson cards for us. Please let me know asap.Thank you
➡️ Reply
#Mutoh by Dio Geonzon on 2013-11-19 21:03
Hello,I have a VJ-1204 and will not power-up at all. Please advise.Thank You,
➡️ Reply
#Mcmartin by dave lantis on 2013-12-23 00:37
Hey, I received the martin from my son as a Christmas gift. I build tube amps, fix Mri\'s for a living. I was wondering if I can pay for a schematic of that unit. Anyway, thanksdave
➡️ Reply
#Macome Corp by Frank Keiser (Keiser Mfg. Inc.) on 2014-02-10 18:04
I am sending the FSH-1460 sensor and the FSD-1460 Amp in for repair. I believe it is the senor pickup that is bad. Unit works and occasionally the spindle will not orient.
➡️ Reply
#Milnor by Orman on 2014-05-10 22:50
I am a business customer experiencing issues with the PC board in my Milnor 08BSPE1T unit. The unit is failing to power on consistently, with intermittent glitches and errors displaying on the control panel. Despite multiple attempts to reset the system, the problem persists, affecting the overall f...
Show More
➡️ Reply
#Mitsubishi by gilliland on 2014-08-01 00:00
Hi there, I'm interested in purchasing a Mitsubishi MDS-A-BT-6 unit. I wanted to inquire about pricing and availability as I'm looking to source one quickly. Thank you!
➡️ Reply
#Magnavox by Anne Rowland on 2014-08-18 00:03
I am in need for a needle for my model 1P3700 stero.
➡️ Reply
#Mitsubishi by FAWZY on 2014-09-18 00:00
Urgent Downtime Report for Mitsubishi MDS-CH-CV-260Hi Team,I am writing to report an unexpected downtime caused by the Mitsubishi MDS-CH-CV-260 unit. Unfortunately, the specific issue is unknown at this time as we are still investigating the root cause.Downtime occurred today at , impacting our prod...
Show More
➡️ Reply
#Martonair by Shailesh Meshram on 2014-09-30 10:12
We require seal kit for SPG/93230/100/K = 25 nos.Also we are interested for dealership in india.We are Distributor for CAMOZZI PNEUMATIC AND ELESA&GANTER MACHINE ELEMENTS IN INDIA.Please confirm.regrads,Shailesh M
➡️ Reply
#Marconi by rosemary bainbridge on 2014-10-17 10:03
wish to purchase or repair 131-9835/04Can you please issue best target prices & capability
➡️ Reply
#Macro Electronics by Gene Hill on 2014-12-15 03:44
I would like to use our church Macro Electronics dimmer with LED lighting, but the LED lights come on full brightness at anything over 25% travel on the dimmer control.Can the dimmer\'s response to the control be changed to control the LED lighting over more of the control range?Thanks
➡️ Reply
#Mikasa by Rondelli on 2015-01-08 00:00
My Mikasa MVH-RT/RC is not working - no power or response. Need urgent repair service as it's used in our daily operation.
➡️ Reply
#Monsun-Tison by Thomas wood on 2015-04-20 14:15
I have a Munson tison CL 303-030A CL2 joy stick, need a tech manual for adjustment and maintance? Thomas
➡️ Reply
#Magnavox by Deloris Barnes (Major) on 2015-06-22 13:12
I like to order a part for an older model bought in (1964). Just don\'t know where a close dealer is today. Please help me on locating a replacement needle. Thank You, Deloris. phone# (615-4546850).
➡️ Reply
#Modex Automation by betty perea on 2015-10-21 19:16
Iam looking for pricing on follow:1PC BATTERY CHARGER MODEL No. BC700, 12VDC, 3A
➡️ Reply
#Monsun-Tison by Perry Merlo on 2015-12-07 15:34
Please give me an estimate to have this valve repaired. It operates the drive wheels on a Simon boom lift. It only allows the machine to move in one direction (forward). I switched the directional hoses around and can tell the problem is with this value as it will go in reverse but now not forward. ...
Show More
➡️ Reply
#Melco by JACK CROWLEY on 2016-04-27 17:22
CAN THEY BE REPAIRED OR ANY AVIALABLE. THANKS
➡️ Reply
#Macroamp by Carl Cheke on 2016-05-02 18:17
Do you repair Macroamp Model B controllers? We have one with the output controlling improperly.
➡️ Reply
#Melco by roger koren on 2016-07-06 22:11
the screen shows nothing when i start up the machine. it is blank.
➡️ Reply
#Melco by roger koren on 2016-07-06 22:14
the screen shows nothing when i start up the machine. it is blank. it is not a monitor. it the screen where you insert the 3 1/2 floppys.
➡️ Reply
#Mitsubishi by St on 2016-07-09 00:56
The Mitsubishi FR-A024-2.2KP is not functioning properly. Please have it checked by maintenance.
➡️ Reply
#Mitsubishi by Mike Stalzer on 2016-07-23 00:00
Based on my previous experience, the MITSUBISHI PD21B CNC module might be experiencing intermittent power loss resulting in frequent system freezing during operation. This could indicate a potential issue with the power supply or internal connections. Further inspection by a qualified technician is ...
Show More
➡️ Reply
#Microtouch by shashi bhusan on 2016-09-11 00:00
Urgent Repair/Replacement Info Needed for Microtouch Systems Inc 11-2301-78kHi ,I'm currently on-site at our office and our Microtouch Systems Inc 11-2301-78k has stopped working. We need assistance with either repair or replacement options as soon as possible. Could you please provide us with detai...
Show More
➡️ Reply
#MICROLAB by Wysocki on 2016-11-14 20:08
The MICROLAB MXP 1500-10 is showing error code E302 and flashing a "Overload" alarm. Power supply is at 10V, 1500A, and 15kW. Please advise on troubleshooting steps. Thank you.
➡️ Reply
#Moog by Baba on 2017-02-13 02:59
I believe the Moog T200-510 is experiencing issues that have caused it to stop working properly. I'm not exactly sure what the model does, but it seems to be a problem with the machine itself. I recommend contacting a technician for further assistance.
➡️ Reply
#Martin-Decker by leila moradi on 2017-02-27 10:25
Dear Sir,Would you please advise me me about H6D-31/H6A-31 TONG LINE PULL/ Martin decker. Hope to receive your catalog.Yours,Leila
➡️ Reply
#Mitsubishi by Lluis j Jaimes Delgado on 2017-03-27 14:00
The Mitsubishi FR-F740-S185K-CHT inverter drive just failed, need immediate attention. No operations until fixed.
➡️ Reply
#Miller by Gilberto Arbelaez on 2017-09-08 00:00
Can the Miller 212886G circuit board be repaired or bought? I'm hoping to check this off my to-do list.
➡️ Reply
#Mazak by Villajulca on 2017-09-15 00:00
We experienced unexpected downtime with the Mazak ksyz407a0 yesterday during the evening shift. The unit malfunctioned around 930 pm, causing a significant delay in production. Looking to resolve the issue
➡️ Reply
#Mitsubishi by blackjack54 on 2017-09-26 07:57
Machine displaying error code E102.
➡️ Reply
#Mitutoyo by MAX SOLOMON on 2017-10-16 00:00
Could you please confirm if the Mitutoyo KS-32 Control Unit is still supported and if replacement parts are available? Thank you.
➡️ Reply
#Microvitec by seng on 2017-11-08 00:00
Urgent Follow-Up Needed Microvitec 38-K31IMA-OP Repair StatusDear ,I am following up on the ongoing issue with the Microvitec 38-K31IMA-OP monitor. The unit is still not functioning, and I have not received any updates on the repair status.Please prioritize this matter and ensure that someone addres...
Show More
➡️ Reply
#Multivac by Dubai on 2018-02-15 00:01
The Multivac AKD-P01207-NCCC-D102 servo drive unit is exhibiting unusual behavior in the warehouse. It is not functioning normally, but the specific issue is currently unknown.
➡️ Reply
#Mitsubishi by Geraldzew on 2018-02-17 00:46
The Mitsubishi HF-KP23B drive or board has failed, needs immediate attention. Operating at less than optimal capacity, affecting production.
➡️ Reply
#Metcal, Inc by Curt on 2018-03-21 16:45
Do you have experience repairing these units? Do you have set pricing for repairs, or is it Time and Materials per job? Do you have a way to test them when completed to be sure they work?
➡️ Reply
#Mitsubishi by M.Kaviani nezhad on 2018-08-09 17:16
Hello, Can you please provide more information regarding troubleshooting and potential repair options for a Mitsubishi A1SJ71AP21 Data Link Module? Thank you.
➡️ Reply
#Meidensha Corporation by manoj badapanda on 2018-09-21 15:35
Hi team, the Meidensha Corporation VT110 H 35B, 5.5A Inverter unit is not functioning properly. Please investigate the issue further. Thank you.
➡️ Reply
#MTS by Ron Kadesch on 2018-12-30 00:00
Inquiry About Pricing and Availability of MTS V-2064-02 N/AHello ,I hope you are doing well. I am reaching out to inquire about the pricing and availability of the MTS V-2064-02 N/A model. My team has recommended this unit to me and I am looking to source one quickly. Could you please provide me wit...
Show More
➡️ Reply
#Minebea Co Ltd by Frauk Hossain on 2019-01-23 00:00
My Minebea Co Ltd 5915pc-22t-b30 unit is not powering on. Looking for a technician who can diagnose and repair the issue
➡️ Reply
#Mazak by Spakvoivili on 2019-03-23 05:50
My Mazak D65UB004850 Interface Board is malfunctioning, causing the industrial unit to be non-operational. Looking for a technician to repair it
➡️ Reply
#Mitsubishi by Ted Acker on 2019-04-21 07:03
The Mitsubishi HF-SP352 3.5kW Servo Drive experienced a malfunction, causing downtime during the last shift. It is crucial to resolve this issue
➡️ Reply
#Modex Automation by P. JAYASINGHE on 2019-06-23 17:54
Please, give me complete circuit diagram of the above charge manual.Thank ,Jaya
➡️ Reply
#Mitsubishi by SADI on 2019-06-29 04:04
Our Mitsubishi FR-E720S-11 SC-EC industrial inverter unit is showing errors and not functioning properly. We need urgent repair service to get it up and running again. Please provide availability for a technician to come to our facility. Thank you.
➡️ Reply
#Micromatik by Emily on 2019-11-11 00:00
There was a downtime caused by the Micromatik 030M1423.R02 CONTROLLER unit. The description of the issue is unknown at the moment. It happened during the last shift, and we need to address it before the next shift arrives. Please assist as soon as possible. Thank you.
➡️ Reply
#Mitsubishi by Jansen Danganan on 2020-01-01 23:22
Our Mitsubishi MDS-B-V2-1005 servo drive unit is still down. We need assistance with this matter urgently. Please respond
➡️ Reply
#Maytronics by Ravi Ranjan Kumar on 2020-02-17 00:00
Hello, I'm inquiring about part number 2410110LF for a Maytronics device. It's described as a Circuit Board. Can you provide information on repair or replacement options? Thank you.
➡️ Reply
#Meridian Instruments by Jarod Ballardo on 2020-04-06 06:21
The Meridian Instruments M.S.T. 9040 Controller Card is currently not working.
➡️ Reply
#Marquip by akbari on 2020-05-05 00:00
Marquip 6280094 PCB Issue ReportHello,I wanted to bring to your attention that we have been experiencing a recurring issue with the Marquip 6280094 PCB unit. Multiple units have been returned or reported with the same unidentified problem. Technicians have noted inconsistencies in the functionality ...
Show More
➡️ Reply
#Melco by JACK L FEAK on 2020-09-04 12:38
We have a Melco EMT 10/4T machine with a start-up boot problem. I believe there may be a electronics hardware problem (memory error?). Error is “BOOT DISK ERROR_”. After replacing the floppy disk drive and new boot floppy disk a closer examination indicates a problem in the self test routine (I thin...
Show More
➡️ Reply
#Mitsubishi by wesley eddlemo on 2020-09-15 04:06
The Mitsubishi FR-A540-22K A500 22KW Inverter is not working.
➡️ Reply
#Modicon by hills on 2020-10-26 00:00
I am reaching out on behalf of my client who is experiencing an issue with a Modicon P810. We don't have the full details at the moment, but we are looking to gather more information to assist with the repair. Could you please provide us with guidance on troubleshooting or repairing this device? Tha...
Show More
➡️ Reply
#Meta Visions Systems Ltd by Muhammad Amjad on 2020-11-09 00:00
**URGENT REPAIR NEEDED**Issue META VISIONS SYSTEMS LTD E811-01 LASER PARTICLE COUNTER malfunctioning. Unable to accurately detect particles, affecting quality control on production line. Immediate attention required to avoid production delays.
➡️ Reply
#Marel by Nols Van Niekerk on 2020-11-19 08:59
Hi,The display of the Marel XL500C just show a white screen.So we are unable to put in any parameters.Is their another way to put in the parameters or do we need the screen?How can we fix the screen.Please advise.
➡️ Reply
#Mitsubishi by BATSCH on 2020-12-03 18:34
Can the Mitsubishi MR-J2S-200B-QR141U633 Servo Drive be repaired or replaced? Trying to check this off my to-do list. Thank you.
➡️ Reply
#Moeller by Flaherty on 2021-03-08 16:05
Moeller ZB4-501-UM4 interface converter showing error code E42, not communicating with main PLC.
➡️ Reply
#Micromint by Michael Long on 2021-03-16 15:56
We have several ancient three board assemblies that are malfunctioning and are unable to test why. RTC-A012E, R1.1 RTC-BUF10, R1.0 RTCV25, R1.0Can you evaluate and/repair them?
➡️ Reply
#Matrix by LAYMAN on 2021-06-12 03:37
Do you have any Matrix MPS-3005L-3 power supplies available for sale or repair? The current unit has stopped working, and we need to keep production running.
➡️ Reply
#Mitsubishi by Mr. Surya Agussatria on 2021-07-19 03:58
Mitsubishi FR-E540-5.5K-CHT inverter displaying "Overcurrent Fault" error code.
➡️ Reply
#Motion Engineering Inc by maintenance dept. on 2021-07-25 11:51
I am a business customer reaching out regarding my Motion Engineering Inc. PC-DSP board that requires repair service. The unit is not powering on properly, failing to boot up or display any activity. After conducting some troubleshooting, I suspect there may be an issue with the power supply or pote...
Show More
➡️ Reply
#Motion Science by Danil nof on 2021-12-19 12:55
We use model msfx12004-03 both axes do not workBRDaniel
➡️ Reply
#Mitsubishi by samir patel on 2022-02-02 03:00
The Mitsubishi ACL022-S input reactor inverter for the 2.2K single-phase inverter 200V caused downtime on . Seeking clarification before the next shift.
➡️ Reply
#Markem by behza on 2022-05-29 00:00
Received alert that the MARKEM 10015190-AR ink pump is malfunctioning due to a drive or board failure. Need to investigate and make necessary repairs ASAP.
➡️ Reply
#Mitsubishi Electric Corporation by Mike m on 2022-06-16 06:23
Hello! I hope you're doing well. I'm working on getting your Mitsubishi Electric Corporation MDS-C1-V2-1010 servo drive repaired or replaced. Before proceeding, I just wanted to confirm if it can be repaired or if a new one needs to be purchased. Your
➡️ Reply
#Monarch by Ron Burnham on 2022-06-28 00:00
Experiencing power issues with my Monarch 50306 unit - not turning on at all. Need immediate service to diagnose and fix the problem. Thank you.
➡️ Reply
#Motion Control Systems by Siqueiros on 2022-08-05 19:20
I'm experiencing some issues with the Motion Control Systems MC1318. It seems like something is not working as it should, and I'm not sure what the problem might be. Any guidance or assistance would be greatly appreciated.
➡️ Reply
#Mitsubishi by eugene a riotte on 2022-09-20 00:00
Mitsubishi MC116 circuit board issue, unit not powering on. Need repair service ASAP.
➡️ Reply
#Mitsubishi by Langhirt on 2022-10-12 00:00
Could you provide further details regarding the malfunction of the Mitsubishi fr-e520-7-5k-na unit?
➡️ Reply
#Moba by majid bagheri on 2022-10-24 06:06
Hello, my client is having an issue with their Moba CSM18 control board (Part Number XXXXXX). They mentioned that there seems to be a connectivity problem. Can you provide some guidance on troubleshooting or repair options for this particular issue? Thank you.
➡️ Reply
#Mitsubishi Okk Hm-40 by Ben Cooper on 2023-05-17 00:00
The Mitsubishi Okk HM-40 is not functioning properly.
➡️ Reply
#Mitsubishi by Iwan Sutio on 2023-07-30 12:40
Hi there, I understand you're having an issue with the Mitsubishi FR-S540E-0.75K-EC unit. From what I gather, it's a 0.75kW three-phase micro inverter compatible with the FR-DU04. The problem seems to be that it's not working as expected. Let me know if you need further assistance.
➡️ Reply
#Mitutoyo by Markiewicz on 2023-08-20 00:00
The Mitutoyo GML-3705WEC counter unit is not working and needs maintenance.
➡️ Reply
#Mitsubishi by Ben Tudor on 2023-10-22 16:28
Mitsubishi Inverter IssueMessageHi there, I was informed that the Mitsubishi FR-E520S-1.5K-EC 1.5kW inverter is not working properly. Kindly assist with troubleshooting or repairs. Thank you.
➡️ Reply
#Myron by GeorgeCib on 2024-01-20 00:00
Urgent Issue - Myron L Company 512m5 Unit DownHey team,The Myron L Company 512m5 unit went down mid-shift last night. Currently, the issue is unknown. Please investigate and follow up ASAP. Let me know if you need any further details.Thanks,
➡️ Reply
#Maxtor Corp by Pier Augusto Majero on 2024-02-08 00:00
I'm having some trouble with the Maxtor Corp PWR SW, MIT40. It seems like there's an issue with the power board. Can you help me figure out what might be going wrong?
➡️ Reply
#Modicon by Souza on 2024-08-13 19:15
We have identified a failure in the Modicon AS-B846-002 16 POINT ANALOGUE INPUT MODULE - CU. This issue is affecting our production line and needs immediate attention from the repair service to minimize downtime. Please address this matter urgently to get our operations back up and running.
➡️ Reply
#Markem by Denis Beaudoin on 2024-08-23 00:00
Markem 0671767 is malfunctioning and causing a significant slowdown in the production line. Immediate repair is needed to avoid extensive downtime and delays in output. Please address this issue urgently to keep operations running smoothly.
➡️ Reply
#Mitsubishi by Pai on 2024-08-30 11:23
Do you have a Mitsubishi MDS-C1-SPH-55 in stock for sale or repair? Our production is waiting on this crucial component.
➡️ Reply
#Mitutoyo by vlasta on 2024-09-09 03:07
Odd Behavior of a Machinery Component in the WarehouseI wanted to bring to your attention an issue with a machinery component in the warehouse. The device is displaying erratic behavior, deviating from its usual operation. It seems to be struggling, making unusual noises, and showing signs of instab...
Show More
➡️ Reply
#Micro Motion by Mamo Boykie on 2025-01-03 00:00
Micro Motion 0273601 rev d showing no display when powered on, potential controller issue. Need urgent repair assistance.
➡️ Reply
#Mitsubishi by Jeff Osborn on 2025-01-20 02:44
The Mitsubishi FR-D720-2.2K inverter unit is not functioning properly. Please inspect and troubleshoot the issue at your earliest convenience.
➡️ Reply
#Metrix Pmcbeta by Vivian curtis on 2025-04-07 17:34
: I am experiencing issues with my Metrix PMC/Beta vibration monitor model GM3221-0102-278. The unit isn't detecting vibrations as it should and I need to have it repaired or replaced. Can you please provide me with an estimated cost for a replacement unit or repair of this model?:
➡️ Reply
#Manufacture2 by Abias on 2025-04-22 11:39
Hello! I am a user of your equipment, we have a problem. We have lost the documentation and instructions. Please help us, we need to configure and calibrate the equipment.
➡️ Reply

Contact Us

🚑Shop Location🛠️

Industrial Electronic Repair
145 Rockwell Place Ct
Tobaccoville, NC 27050
🚑 Rush repair shipments only — no walk-ins.

📞Phone

1-336-969-0110

📦Mailing Address🚛

Industrial Electronic Repair
931-E S. Main St #204
Kernersville, NC 27284
📦 Mailing Address (for invoices or shipped repairs)
No walk-ins accepted.