R Service & Repair Forum

If you need your unit tested or repaired then give us a call.
We offer fair estimates and offer extended warranties.

You can contact us at 1-(336)-969-0110
Shipping/Receiving
Industrial Electronic Repair
931-E S. Main St #204,
Kernersville, NC 27284
Phone: (336) 969-0110

We repair industrial electronic devices

If you have an industrial electronic device that needs repair,
Feel free to contact us!

— Posted by Sales on 2005-05-09

Reply🗨️Ask a New Question Below❓

If you need your R unit tested or repaired,
give us a call at 1-336-969-0110.
We offer fair estimates and extended warranties on the work performed.
Shipping/Receiving:
Industrial Electronic Repair
145 Rockwell Place Ct
Tobaccoville, NC 27050
Phone: 1-336-969-0110

Recent 430 Comments

#Randtronics by Jamey Kahle on 2005-10-20 19:41
Do you have or could help me find a wiring diagram for a Randtronic DC Drive Model: SB-250Thanks
➡️ Reply
#Randtronics by Geo Suchora on 2005-11-08 17:42
I also have the same model but have no wiring diagram. Could you help with this?
➡️ Reply
#Robotool by karl rezmann on 2005-11-18 02:43
faster pc based control available ?std 1.44 floppyeasy edit on std pcetc
➡️ Reply
#Rittenhouse by Tom Mitchell on 2005-11-30 17:54
I have a Rittenhouse Home Intercom, Model No. M7010 that had no audio. A technician said the amplifier was bad and he replaced several transistors in it, but the volume is very weak. He does not know exactly what transistors to use to replace the old ones, and does not have a schematic. Can you prov...
Show More
➡️ Reply
#Relcon by Shawn Gordon on 2006-01-17 22:53
We have a drive that is causing us issues and want to know if you repair boards for a 10 HP Relcon Inc Dynamatic AFR-7000 series drive. Or if you know of a company that repairs this style of boards. Model # AFR-7015, some of the part numbers for the boards are 15-565-16,15-646-106R, 15-565-9 & 1...
Show More
➡️ Reply
#Rustronic by Godfrey Saldanha on 2006-02-20 04:51
The MMI for our Ruston Gas turbine control system has failed. We are unable to obtain a new MMI from the manufacturer (NEC NL10276AC24-01). We wish to enquire if you can repair this MMI and load the software. We have the neccessary software. including the intelligent display software Rustronic MKII ...
Show More
➡️ Reply
#Rittenhouse by David Peterson on 2006-03-01 03:17
The reception is pretty poor and weak on the volume. Do your know if there is an transisterized replacement receiver that will fit into the 1970\'s model. Thanks, David......
➡️ Reply
#Rittenhouse by bill morrison on 2006-05-03 03:40
we have an old rittenhouse intercom system. the units look old but still works fairly well. need information on how to update system look without replacing entire system. we\'re remodeling in some areas and would like to check out updating units. don\'t have specs on the system. not sure of
➡️ Reply
#Rittenhouse by SUSAN R BOYD on 2006-05-16 13:16
My mom and dad has an old (approx.37yrs) rittenhouse intercom system and they need a replacement bulb for the main unit. I\'ve tried searchingonline but since mom nor dad know the exact part # i\'m having no luck.Dad said it was a low wattage pilot lamp?? GE19 or R19???? Any help you can offer would...
Show More
➡️ Reply
#Reta Electronic by Alena Sukova on 2006-05-22 14:21
We have RETA Electronic control units for DC motors type 222/22, 223/23. We are trying to find the place where somebody can adjust and repair them. Is there any place in the Czech republic or Europe you can recommend? Thank you in advance for your reply.With best regards,Alena Suková
➡️ Reply
#Rittenhouse by Dale Adams on 2006-05-28 16:30
My unit is in need of repair, can you help ?
➡️ Reply
#Rittenhouse by Barbara on 2006-08-27 17:45
This is an old system I would like to replace. Does the wire plugs have to be replaced. I would like sm=omthing that will be compatable with the wire plugs. Do you have any suggestionsThank You
➡️ Reply
#Rittenhouse by william hogan on 2006-09-05 18:05
I have a rittenhouse am radio intercome that works well. It has 7 receivers + the base unit. can it be changed to fm ? I believe it is a late 60s mdel. thanks
➡️ Reply
#Rotaprint by DRAGOS on 2006-10-16 21:28
I want to ask you if you have an electronic diagram for ROTAPRINT 37 KGM SERIE 3-64165, YEAR 1987 Thank you General ManagerDragos Acsente
➡️ Reply
#Rondo Electronics by Lufthansa Flight Training, Rudolf Strohmenger on 2006-11-06 12:36
Frankfurt, Nov. 06-2006 Dear Marty A. Lineberry,please give us the shippingdetails for our repair order. Model Number:SII1240-200 P/N:25581687. Please give information, because it is very urgent.
➡️ Reply
#Rustronic by frank krämer on 2006-11-27 13:20
Dear Sirswe are looking for a company which able to change the Rustronic PLC parameters, can you offer us your expert to come to Germany.Best regardsTUBAFrank Krämer
➡️ Reply
#Reutlinger by Mike Jones on 2007-01-30 01:23
We have a Reutlinger Compu-balance. Do you repair this equipment? Also do you know where we could get a copy of the operation manual?Best regards,Mike Jones
➡️ Reply
#Rittenhouse by paul suter on 2007-02-12 03:05
I have a old intercom in an apartment building that has door locks, buzzer, and voice. the call and voice speaker does not work. all the other apartments are working good. Is there a replacement for the apartment units. or a upgrade?
➡️ Reply
#Reta Electronic by EDGAR DIAZ SANCHEZ on 2007-02-19 15:59
WE ARE PROCABLES S.A. AN INDUSTRIAL CABLE MANUFACTURING COMPANY IN BOGOTA, COLOMBIA.WE HAVE SOME DRIVES D5200 AND WE NEED MANUALS OR PLANS FOR RETA ELECTRONIC D52 SIEGBURG BV 70/2-80-1K.Nr. 847006YUOR HELP IS TRULY APPRECIATED
➡️ Reply
#Rittenhouse by Jay Sturm on 2007-02-24 18:35
Dear Sir: I\'m looking for a electric schamitic for an Emerson Rittenhouse intercom Model rm20/rm22. Any help in this matter would be appropriated. Thank You, JAY
➡️ Reply
#Rittenhouse by Melvin Chrisman on 2007-02-24 22:05
I have a radio intercom unit that needs to be updated.
➡️ Reply
#Rittenhouse by Donna Dodson on 2007-03-02 16:22
I would like to see if I can get this to work. But I don\'t know where to start.
➡️ Reply
#Reutlinger by ERCAN ÖZERCAN on 2007-03-06 08:24
We have a Reutlinger Compu-balance.Its code is 701.00.030 and ýts probe coded with 770.00.055 is broken. can you help or repair this equipment for us? We will wait your reply. Thanks and Best regards,Ercan Özercan
➡️ Reply
#Rustronic by Do Trong Nghia on 2007-04-04 10:50
Dear Sir,We are using turbine TB5000 to drive water pump.I want to force the supply valve (SOL-11)and vent valve( SOL-12). But I can not force them by command CHG SOL11,1. When I type this command, the LED on card is on in short time. There is no signal at terminal. What Module must I choose? Why no...
Show More
➡️ Reply
#Rustronic by Do Trong Nghia on 2007-04-04 10:56
We are using turbine TB-5000. Now speed is panel control. I wish control speed by analog input. May I have the program of this method?
➡️ Reply
#Rittenhouse by Bob on 2007-04-07 23:14
We have the same system in our home. Did you find any compatible system? Did you replace your system? If so, what system did you use? Thank you. We need to replace everything except the wiring.
➡️ Reply
#Rapid Electric by Judy Jankowski on 2007-04-12 18:46
I need a new spring that holds the dryer onto the stand, actually Two springs for I have another dryer, same problem, Old dryers but still work. Speedy Dryer ser.8565 Model 100 Do you have such an Idem? Thanks Judy
➡️ Reply
#Reta Electronic by Gavin Gossayn on 2007-04-20 15:15
INSTALLATION AND WIRING DIAGRAM FOR DRIVERETA TYPE, 5200 RANGE SER NO S.1.531-12-10-2URGENTLY REQUIRED
➡️ Reply
#Reta Electronic by GAVIN GOSSAYN on 2007-04-20 15:18
Manual for 5200 range needed URGENTLY PLEASE.Serial no S.1.531-12-10-2
➡️ Reply
#Randtronics by zawahir on 2007-04-24 08:19
industrial machinery 3 phase wiring diagram
➡️ Reply
#Rittenhouse by DAVE ROSS on 2007-05-18 16:21
EVERYTHING WORKS FIND..JUST WANT TO UPDATE OLD UNIT
➡️ Reply
#Rittenhouse by Francis Roberts on 2007-05-24 22:32
Need new springs for the hammers. This is an old door bell and it has lasted about 40 years. The new ones are sick. This is the best I have heard and would like to keep it another 40 years.
➡️ Reply
#Reliance by Mayen Udoh on 2007-06-04 00:00
Hello, One of our employees has a Reliance 705330-28s that stopped working, and they need a replacement. We are looking for repair information or guidance on where to find a replacement. Is this something your shop can assist with? Thank you.
➡️ Reply
#Rittenhouse by vero cho on 2007-06-19 19:49
sheetrocking my house after it was flooded by katrina, the contractor stupidly threw away the master station to my doorbell/radio/intercom system which rendered the system inoperable. i have asked an electrician friend to look at it and he cannot find a suitable retrofit. we will have to replace the...
Show More
➡️ Reply
#Rittenhouse by v on 2007-06-19 19:52
my dilemma also. have you found a suitable replacement? thanks.
➡️ Reply
#Robotool by Charles Park on 2007-07-28 19:56
Have a problem with operating system, here is the error that I am getting when trying to boot up system.Is there any way to get a copy of the master disk?Or is this a hardware problem, like mabey the mother board is goneBad or missing \\dos\\ himem.sysError in config.sys line2Hma not available: load...
Show More
➡️ Reply
#Rapid Electric by scott taylor on 2007-07-29 15:30
looking to repair a speedy dryer volts 110,120 ac, 60 hz
➡️ Reply
#Robotool by AL on 2007-07-31 21:06
It appears that your himem.sys file is corrupted or missing.config.sys line 2 error is probably calling for this file.Open the file with notepad.exe and see. (or boot up w DOS floppy. type: Edit config.sys or open config.sys)if so, simply copying the himem.sys from your DOS disk could fix the proble...
Show More
➡️ Reply
#Robotool by tom burgmeier on 2007-08-16 15:45
I have a cvm-1 they offered a upgrade with a new pc paised system for $5,000.00 cookbook change up. Do you have such a system you offer? I didn\'t like the CPM disk drive and only 2-1/2 axis contouring.please fax,email, or calltom burgmeierlibety machine & tool7908 ontario avecicero ny 13039fax ...
Show More
➡️ Reply
#Rittenhouse by Ronda Plomteaux on 2007-08-19 15:03
I have a Rittenhouse intercom system and am unsure of the model #. It was installed in the 70\'s. I am painting my condo and would like to replace the ivory cover with a white cover. How would I go about purchasing just a cover? Thank you
➡️ Reply
#Rittenhouse by glen e peterson on 2007-08-23 19:16
I h ave a rittenhouse intercom system that does not work star system 9000 I would love to get it to work again. Can you help me with this thankyou glen
➡️ Reply
#Reliance by digicase on 2007-08-27 00:00
Hello,I'm in the purchasing department and need information on repairing a Reliance 1su21003 that has stopped working. Can you please provide details on the issue and if a replacement is available?Thank you.
➡️ Reply
#Rittenhouse by Mickey Loveria on 2007-08-30 14:53
Existing model was put in my home maybe late 60\'s, with ivory base unit and 4 ivory receivers plus brass door unit intercom. The radio reception is irregular, fades in and out and there is much static. Sometimes have to jiggle knobs on base unit to tune radio! Any suggestions on where to go for upg...
Show More
➡️ Reply
#Rittenhouse by Jim Wilson on 2007-09-11 01:47
Ihave a 20 year old rittenhouse intercon that does not and love to get it working again or replaced can you help
➡️ Reply
#Rittenhouse by Jens on 2007-09-29 19:23
Hi We stock this lamp in Sweden Price is 2 $ each + shipping (mail)JENSwww.JENSIgame.comJens@jensigame.com
➡️ Reply
#Rapid Electric by Joy Kelley on 2007-10-21 03:14
I need a switch cover and new wheels for my Speedy Dryer. Can you help?
➡️ Reply
#Rittenhouse by TR on 2007-10-27 18:13
I have a Rittenhouse intercom system that was installed in the 60\'s that worked fine until recently. Everything still works fine except the main intercom/control unit. Is there a replacement unit I can buy that I can use with all my existing speakers, etc throughout the house? Even a unit that only...
Show More
➡️ Reply
#Rittenhouse by Marie Gunderman on 2007-11-26 01:41
We purchased our present home in 1998. It was custom built in 1983 with many upgrades that were available at that time. Unfortunately since we have lived here the system does not work. The main unit is 17\' wide and 9\" tall. There are 12 units scattered throughout the house. They each measure ...
Show More
➡️ Reply
#Rittenhouse by Kathryn Fenich on 2007-12-18 20:21
Rittenhouse Solid State AM/FM radio intercom system for house and outdoors
➡️ Reply
#Rittenhouse by Eric Hoffman on 2007-12-23 04:40
I have just recently purchased a house that has a Rittenhouse Model 7300 Intercom system that does not work. I am trying to find a schematic for it. I know that it is an old system, but would like to use it to monitor my young children. Any help would be appreciated.Thank you.Eric Hoffman
➡️ Reply
#Rittenhouse by GARY KASPRZYK on 2007-12-26 16:12
I HAVE A RITTENHOUSE INTERCOM AM/FM SYSTEM , MODEL # 9042 AND I AM TRYING TO FIND OUT WHAT SIZE[POWER REQUIREMENT] TRANSFORMER [ 4 WIRE] I NEED. I DO NOT HAVE THE OLD ONE. ANY HELP WOULD BE APPRECIATED. THANKS
➡️ Reply
#Rittenhouse by Hans Otto Mertens on 2008-01-01 23:36
The main unit needs repair!H.O.Mertens
➡️ Reply
#Reta Electronic by ingolf Christiansen on 2008-01-02 09:17
Please help us if posible with a manual on Reta Electronic BW 522/06We is not certain on what the problems is.Best regardsIngolf ChristiansenFax: ++4546482868
➡️ Reply
#Roundo by eddie on 2008-01-11 15:14
i need a wiring diagram for a roundo roll model pas420
➡️ Reply
#Rapid Electric by Sandy towne GROOMINGDALES on 2008-01-23 17:31
I need the plastic attachment on the end of the blower hose for a Speedy Dryer 110 volt model 900 serial number 30449188. Can you help?
➡️ Reply
#Rittenhouse by jimmy jamison on 2008-04-08 19:34
we have modle m7035 the door bell and gate buzzer in still workes but the talk butten and volumne dose not. would like to fix or replace unitplease help thank you
➡️ Reply
#Rotaprint by Banceanu Vlad on 2008-04-24 06:16
I want to ask you if you have an electronic diagram for ROTAPRINT R36 KVThank youGeneral ManagerBanceanu Vlad
➡️ Reply
#Rustronic by Dilip Hutheram on 2008-04-29 08:24
Please find below the complete part numbers for the Rustronic vibration modules I required for the Gas Turbine. Module 4509 Part no. : 4509/20 64/07004230/20 950279/1/2 (SR6113/06) (SR6129/06) Module 4502 Part no. : 4502/30 64/07004230/30 950279/1/5 (SR6127/03) (SR6113/23) Module 4504 Part no. : 450...
Show More
➡️ Reply
#Rittenhouse by Jim Drouillard on 2008-05-16 02:50
I have the above mentioned door chime (Rittenhouse door chime model C8536) that does not work correctly. There where some broken wires from the transformer coils that I soldered back on and now it does not work correctly. Do you have a schematic for this unit?
➡️ Reply
#Rotaprint by ernest nartey on 2008-05-16 22:02
notes of how to repair all kind of t.v and vcd and dvd decks ERNEST NARTEY P.O.BOX 782 ASHAIMAN W/A GHANA 00233
➡️ Reply
#Rustronic by Ignacio Pinedo on 2008-05-18 16:14
I have an SCM card PN CT92475A/03 on a rustronic control system that is causing me trouble. The customer has a replacement card with P/N CT92475A/01 and I do not know what the differences are. Can you support?Customer is due to replace this sytem for a woodward micronet in the next four months.Regar...
Show More
➡️ Reply
#Rittenhouse by jason surrette on 2008-05-21 22:34
Don\'t know what\'s wrong with the unit. Do ya\'ll know what the input voltage is supposed to be? The back of the unit says only use a \"no. 35 transformer\".
➡️ Reply
#Rustronic by Torben Espoe on 2008-05-28 18:10
I have tried to program this pcb for my washing machine, but it keeps coming up with E90 when I turn the machine on, as if it isn\'t programmed. But when I check the program adresses, the data is correct. I have noticed that the software ver. is W2C01551, is there perhaps an other thing that I need ...
Show More
➡️ Reply
#Rittenhouse by James A. Mann on 2008-06-26 12:40
We installed our Rittenhouse intercom system in 1978 when we built our new home. The speakers look out of date and would like a better main unit. We have 4 outside units, and 7 speakers.Can we purchase new units and still use the same wiring? Would appreciate a response ASAP. Thanks Jim MannP.S. Ple...
Show More
➡️ Reply
#Rte Power/Mate by Fred Hallmark on 2008-07-03 15:44
Where can I get a service manual or schematic for this unit? Thanks for your help.
➡️ Reply
#Rittenhouse by Adrian Younger on 2008-07-08 00:43
Hello. I have an Emerson-Rittenhouse Door Chime Model RC577 and it has quit working. I was wondering if there is a replacement transmitter available for this chime. It has the motor attached to the transmitter so I don\'t htink I can get a replacement at a store. Any information you could give me wo...
Show More
➡️ Reply
#Rotaprint by Ramaswamy.S on 2008-07-10 06:31
Dear Sir,We are leading manufacturer of Printing and Allied Equipment in India with installations over 6750 in 40 countries.We manufacturer Pack to Pack 2 colour offset with fully pneumatic and servo controlled tractor feeding to enable printing any form length between 7\" to 13\" without ...
Show More
➡️ Reply
#Rittenhouse by Derek Rust on 2008-07-26 15:22
I am interested in buying your intercom, I had mine accidentally ripped out during remodelling and need a replacement , does yours work ok?Derek Rust
➡️ Reply
#Rittenhouse by Delia Castillo on 2008-07-29 03:14
we bought this house with installed system. not working. power source not found.
➡️ Reply
#Rittenhouse by lausanne walter on 2008-08-03 14:55
I have about a 1984 model, 16.5 inches by 9 inch am/fm intercom unit........unit does not work anymore. Cannot pick up radio stations by dialing the knob......do you have a replacement unit that would fit this spot? Or is it repairable?Lausanne
➡️ Reply
#Reta Electronic by enviniohody on 2008-08-18 18:36
I\'m new here, just wanted to say hello and introduce myself.
➡️ Reply
#Rittenhouse by Pamela Brawdy on 2008-08-19 20:43
My sister inlaw gave me this doorbell clock, I do not have the chimes the model number is RC6333. Can you help.
➡️ Reply
#Rustronic by souane lak on 2008-08-25 10:43
I did a loading to PPM1 slot0 and PPM1 in slot1 but the LEDs on PPM1 slot1 are still on.What\'s the problem?I did loading using VT100 terminal.
➡️ Reply
#Rittenhouse by Shigong Yang on 2008-08-27 03:12
The system is old and has not worked when I bought this house. Wish can fine some one to fixe and test it.
➡️ Reply
#Rapid Electric by GEORGE BROWN on 2008-09-09 16:33
NEED SPRING FOR CYCLONE 5000 DRYER
➡️ Reply
#Rittenhouse by Jack Mc Sweeney on 2008-09-10 22:29
This is a two unit intercom and door opener for apartments. Presently, it has current but buzzes the door open without pushing the switch, and has no voice tones.
➡️ Reply
#Rittenhouse by DeLane Smith on 2008-09-16 13:35
I need a address to send this unit to get it repaired
➡️ Reply
#Ratelco by john arnaiz on 2008-09-18 06:24
Good daY!I just want to know the specifications for the Integrated control and Alarm card, FC series for Ratelco battery charger...and if its still available in the market?.We hope you could give us a little favor regarding this request..Than you so much!...
➡️ Reply
#Ruhrgetriebe by Mike Schwartz on 2008-09-25 12:53
We have an inverter drive that has the Rhurgetriebe name on it. The model # is Rofre 89710037. The touch pad has been damaged and needs repair. Is this something you can do?Thanks for any help,Mike SchwartzPowers Inc.
➡️ Reply
#Rittenhouse by tom roegner on 2008-09-26 22:07
Eight chime unit {552} repeats sequence continually until switch is disconnected. Switch has been replaced but problem continues----any ideas and is it repairable.....
➡️ Reply
#Rittenhouse by dave walters on 2008-10-24 14:59
Just wondering i have a rittenhouse system rcm-1 and the intercom system part does not seem to be working. We can broadcast for the main unit and it is heard in the other units but when we try to broadcast from one of the other units to the main you can not hear the person ? Anysuggestions or do you...
Show More
➡️ Reply
#Rittenhouse by Larry M Biviano on 2008-11-21 02:47
have hooked up several ways appear to only chime once as if wired for back door.clock woriks fine, does ot chime on all tones
➡️ Reply
#Rittenhouse by Jeffrey on 2008-11-22 22:27
This problem may be caused by a lighted doorbell. After the bell is wrung, the light will re-illuminate. When that happens it may be drawing just enough power to make the door chimes think that the button was pressed once again. This is a repeating pattern.If a lighted door button is used, the solut...
Show More
➡️ Reply
#Rustronic by Haresh PChavda on 2008-11-23 12:59
Dear sir with referencve to our organization we have installed Rustronic MKII software RP2 for EGT turbine (European Gas Turbine ) this system generate a message around 4000 for troubleshotting so if i want to know all the message how its create through varuious types of input /output comming from f...
Show More
➡️ Reply
#Rvsi by Smith on 2008-12-15 11:01
Dear sir:Do you have repair RVSI LS-5700 inspection experience.I have one sensor head want to repairIf you can repair , please tell us. ThanksRegards,Smith
➡️ Reply
#Rittenhouse by Theresa Perkins on 2008-12-16 16:21
I would like to install my RC633 which I removed from my old house. Can you send me instructions? Thank you.
➡️ Reply
#Rittenhouse by Lori on 2008-12-29 00:49
Years ago lightening hit house the chime stoped working the unit is in the kitchen and of coarse the door bell at the front door to push with finger ..doesnt work anymore can this be fixed ??/
➡️ Reply
#Rittenhouse by Jim on 2008-12-29 15:59
Are there any Emerson Rittenhouse intercom main stations from the mid-sixties available?
➡️ Reply
#Rittenhouse by Richard Greene on 2008-12-30 17:19
I own a late 60\'s Emerson Rittenhouse Model RC633 door bell Chime.The clock works fine but the door bell doesn\'t.I believe there is a problem with the motor.Can I have this unit repaired and approximately the cost?
➡️ Reply
#Rittenhouse by Paul E. Nelson on 2009-01-19 18:06
Our house came with this intercom system. Very Old I suspect. Is there anyone who could furnish me with a copy of the ownual\'s manual-instructions? Paul
➡️ Reply
#Rauland-Borg by craig rogers on 2009-01-20 01:25
We have a raulan-borg mcc110 system at our facility and i am looking for a manual for it, with wiring schematic. Can you help?
➡️ Reply
#Rittenhouse by j and c on 2009-01-23 19:43
we have an old set of chimes which were taken from our hallway after a fire, now they require repair, model number is not visible, however, it is a four long pole, with 4 or 8 note feature.would love to repair this
➡️ Reply
#Rte Power/Mate by kimon vidalis on 2009-01-26 06:48
We need to know the price for buying a BPA-40G Power Supply and its publications.
➡️ Reply
#Rittenhouse by Martin on 2009-02-08 05:30
I have the exact same problem, but it\'s not caused by a lighted doorbell. Without the doorbell connect (and not crossing the wires) the chime mechanism keeps repeating. I\'m not sure whether it\'s because the contacts aren\'t lined up correctly or whether it\'s a wiring problem. I\'ve tinkered and ...
Show More
➡️ Reply
#Rittenhouse by matt arendt on 2009-02-08 18:51
need troubleshooting info on rittenhouse model m7900 amp ser# 3060-0074-2091. also, price and availability of parts as i am working on an intercom system in a 8 unit condo.
➡️ Reply
#Rittenhouse by DARLENE on 2009-02-09 03:51
it will not turn off a red light stays on. do i need to replace or repair it.
➡️ Reply
#Rittenhouse by Ron Abrams on 2009-02-18 02:03
I\'m working on a unit which has been in the family for years.Emerson- Rittenhouse RC 633, 16 voltOne of the solenoid/hammers don\'t work. Seems that the hammer is jammed in the tube. I\'d like to replace the solenoid. How may I order another one.Ron 305 803-5441
➡️ Reply
#Robinair by Richard Pring on 2009-02-24 04:11
I am looking for the carbon contact blocks that mount at the end of the tongs on this soldering device. Please advise the price and availabilty. Thank you. Richard
➡️ Reply
#Robinair by Richard Pring on 2009-02-25 02:14
2nd request. I am looking for the carbon contact blocks that mount at the end of the tongs on the model 14492 soldering device. Please advise the price and availabilty. Thank you. Richard
➡️ Reply
#Rittenhouse by van Aree on 2009-02-26 20:19
I am looking for a copy of Rittenhouse rm5 house intercom owner\'s manual.
➡️ Reply
#Remco by Steve Maskovich on 2009-03-08 00:00
Remco 2153 controller not responding to input commands. Need assistance with repair.
➡️ Reply
#Rittenhouse by Kathie Hiers on 2009-03-11 03:19
I bought a house built in 1950 with an old Rittenhouse door chime, Model #365. I have no idea if it can be repaired. I don\'t have the front door button. The inner workings are very dirty. Do you think it\'s worth sending to you? Thanks, Kathie
➡️ Reply
#Rittenhouse by David Smith on 2009-03-16 13:36
I need the three coils for the 526 Rittenhouse. ( a power surge burned 2 of the three).
➡️ Reply
#Rittenhouse by Barb C on 2009-03-27 12:35
Same as James Mann note - have 1970\'s Rittenhouse intercom---can we replace old system - can we purchase new units but use same wiring??
➡️ Reply
#Rotaprint by Chelmus Constantin on 2009-03-27 17:45
I\' have forwor about electronic diagram for ROTAPRINT R37 KV.
➡️ Reply
#Ratelco by Michael Beanland on 2009-04-08 17:51
I am looking to purchase or acquire an O&M manual for a Ratelco FF12012.
➡️ Reply
#Rittenhouse by arnny on 2009-04-14 22:14
I need a power suply for my Emerson-Rittenhouse model RC 633
➡️ Reply
#Rittenhouse by Dick Dingman on 2009-04-20 19:15
I purchased this residential unit in 1986. It is now giving a significant hum and does not produce all of its chimes.Does this give you a clue as to repairability?
➡️ Reply
#Rittenhouse by Jennifer Walker on 2009-04-26 01:22
I have read several threads asking about updating an old Rittenhouse system. I would like to do the same, hopefully avoiding the need to replace drywall, etc., since this system is considerably larger than the Nutone products. I couldn\'t find any responses addressing whether or not there were solut...
Show More
➡️ Reply
#Rittenhouse by Doug Wood on 2009-04-27 20:03
Buying a condo with an inoperative Rittenhouse Model 7021 intercom system. Was constructed in late 70s. Is the technology so out of date that it is not worth restoring? Should I consider restoring the unit, about how much am I looking at? Is there a dealer here in AR, or do I have to ship it to you ...
Show More
➡️ Reply
#Ratelco by bert hunter on 2009-04-29 18:11
i\'m looking for Ratelco manuals for model #102B-3608-00Atype FC48 1505Athanks for any help
➡️ Reply
#Rotaprint by Abdul Ghaffar on 2009-05-18 17:41
i want rotaprint GBM diagram.it is very complicated machine about wiring.
➡️ Reply
#Rittenhouse by Michelle NEWBY on 2009-05-20 00:04
Wee have an Emerson Rittenhouse doorbell model #RC552-1. The motor has fried itself. Can you repair? Thank you. H - (805) 685-2317
➡️ Reply
#Reseco Elettronica by Joe Steward on 2009-05-21 14:58
Could you possibly have a manual for this unit. Roseco Electronica 00A85?I am having trouble with it but can\'t varify if it is in the unit or the wiring to it. Best Regards: Joe Steward
➡️ Reply
#Rittenhouse by Scott Poulos on 2009-05-23 13:59
I am looking for a replacement unit or one that is compatable and larger to cover existing hole. please respond even if you are not interested or cant get what I need so I can try elsewere.
➡️ Reply
#Reta Electronic by Eidher on 2009-05-25 11:22
Hallo!I´m from austria and i would realy need a manual or some plans for this typ! I hope you can help me!kind regardsEidher Timotheus
➡️ Reply
#Reta Electronic by Eidher Timotheus on 2009-05-26 05:47
You could realy held me very much, if you can send me some Informationes, Manuals, Plans, ... from a RETA ELECTRONICS Converter BV 532/45-13-02.Thank youEidher
➡️ Reply
#Reta Electronic by Barry Keech on 2009-05-30 13:01
I have two 5200 BV 532/650l-22-02 DC drives. I do not have a connection diagram for them and would like to recieve a manual or a simple diagram of the connectins, I am prepared to pay for them as the drives are valuable and I cannot use them presently. regards Barry Keech
➡️ Reply
#Rittenhouse by Leslie Southern on 2009-06-05 13:08
We are looking for the Rittenhouse C8931R Wireless Chime Receiver.We are an electrical contractor and are working with a customer who loves her chime system but wants to expand it to other areas of her home.Can you point me in a direction to locate one of these?Thank you.
➡️ Reply
#Rittenhouse by k. chang on 2009-06-17 02:34
how do we get this old door chime to work again?we\'re already replacing the batteries, what else should we do?thanks
➡️ Reply
#Rittenhouse by roger crosby on 2009-06-22 18:11
I have renovated my house. I have a Model RC577 chime that is not working. I seem to have all the parts, 4 chimes, motor, etc.Please help me figure out how to repair.thank you
➡️ Reply
#Rittenhouse by Kenneth Jackson on 2009-06-25 01:00
I have had this for almost 50 years and the clock does not work, for some unknown reason, and the chimes are weak sounding and miss at times. I need help. Can this be repaired?
➡️ Reply
#Rittenhouse by neil Berman on 2009-07-08 05:25
I have a Rittenhouse Model S7806 Smoke/Fire detector system in my 3-level condo. It was there when I moved in so there is no manual for it.My problem is, after a thunder and lightening storm the other day, I came home to find all 3 units ringing. The only way I could silence them was to switch off t...
Show More
➡️ Reply
#Rittenhouse by Howard Hendricks on 2009-07-12 04:29
I have a Rittenhouse Chine door bell with four long poles. The model number is c8578-1, The unit will not work, I noticed two bad diodes, and removed them I am having problems locating the right ones. Is this something you can fix?
➡️ Reply
#Rittenhouse by peter oliver on 2009-07-16 23:50
I am looking for a remote button for this system.Would possibly trade a receiver unit as I have extra.
➡️ Reply
#Rittenhouse by Maryellen Boudria on 2009-07-19 19:15
I have a Rittenhouse chime Model #410 with it\'s companion two chime on second floor of our 1927 home. The door bell chime works however we are not getting all chimes to work. Only two tones downstairs. Can this be repaired? Please advise.Also, can you tell me how old this model of Rittenhouse is?Ma...
Show More
➡️ Reply
#Rittenhouse by scott grim on 2009-07-22 11:43
I\'ve recently come in the possesion of an emerson-rittenhouse model 633 door chime and clock. Somebody must have placed 120volts of power to the 16 volt circiut burning out all the electronics. I need all the electrical components including the hammars and motors. if anyone knows where i can get pa...
Show More
➡️ Reply
#Rittenhouse by DominicJ. Carini on 2009-07-23 03:03
I have a 30 year old rittenhouse door chime with the 4 sequential chimes, one of the plungers has gone lazy. I took the transformer out to try to clean it and lost the little spring that gives the plunger resistance . Do you have any ideas ?Or do you sell parts, perhaps a whole tansformer. I tried t...
Show More
➡️ Reply
#Rittenhouse by dominic Carini on 2009-07-28 00:55
Ihave about a 30 year old rittenhouse with 4 chimes.It seems that the solenoids that activate the strikers,are getting a little lazy.I have had one apart and try to clean it ,with not much succes,I even lost one of those tiny springs. I tried to replace it with a similar one ,but it\'s not right.Do ...
Show More
➡️ Reply
#Rittenhouse by vera price on 2009-07-29 12:53
I have a door bell Model C8229 that started to make a ringing sound. It looks as if the plates are vibrating.
➡️ Reply
#Rittenhouse by charles dellasala on 2009-08-08 20:37
7th chime does not work can plunger be lubed if so with what
➡️ Reply
#Rittenhouse by Janice Lopez on 2009-08-12 02:45
I AM LOOKING FOR A DOOR CHIME FOR MY BUSINESS THAT WHEN SOMEONE ENTERS THE FRONT DOOR THAT I WILL BE ABLE TO HEAR THE CHIME IN OTHER AREAS OF MY BUILDING AS WELL. I NEED SOMETHING THAT WILL HAVE A LOUD CHIME BECAUSE MY BUILDING HAS MACHINERY RUNNING ALL THE TIME. CAN YOU SEND ME SOME INFORMATION. TH...
Show More
➡️ Reply
#Rittenhouse by Jamie Wingler on 2009-08-30 05:41
I have an inoperative Rittenhouse Model 7021 intercom system as well. Can I fix it or do I have to buy new?
➡️ Reply
#Rytec by Don Reed Bonita Packing on 2009-09-03 18:03
I just replaced the control board on a RYTEC High Speed roll up door. Rytec doesn\'t offer a repair service for the board I removed and I\'m looking for that service.
➡️ Reply
#Rte Power/Mate by John Wilcox on 2009-09-25 01:48
Can I get a copy of the ES-24E supply schematic?
➡️ Reply
#Rotaprint by Kire on 2009-10-02 21:07
ask you I need elektronic scheme for Rotaprint R35KfastThank
➡️ Reply
#Rittenhouse by Frank Giudice on 2009-10-23 16:36
I have a clock and doorchimes door bell model RC-633.I would like to get relacement part for the door bell part the clock is still working.Can you help me
➡️ Reply
#Rowan Elettronica by RALPH PENROSE on 2009-11-03 08:54
We have two cable coiling machines with Rowan Ellronica systems and would like to obtain information on how to synchronise the linea and motor speeds.We do not have Model numbers-but can Email photos of the machines.Would you be able to assist us???regards
➡️ Reply
#Rittenhouse by Agnes R. Kellan on 2009-11-06 01:18
I have my radio-intercom since 1969--In hasn\'t worked for about three years. I have two stations.
➡️ Reply
#Rittenhouse by Richard Greene on 2009-11-07 15:09
I have a clock and doorchimes door bell model RC-633.I would like to get relacement part for the door bell part, the clock is still working.Can you help me
➡️ Reply
#Rittenhouse by Chris Pellicano on 2009-11-11 03:52
I would like to get an estimate on testing and repairing any needed parts of our antique ( assuming it is antique,) doorbell. I love the way it sounds, from manually striking the chimes, but doesn\'t seem to work...
➡️ Reply
#Rittenhouse by rosemary ortiz on 2009-11-11 22:30
we can not get it to chime in sequence. if doorbell is pressed it chimes once (#4).
➡️ Reply
#Rittenhouse by Alex Gracia on 2009-11-13 05:30
I\'M A ROOFING CONTRACTOR IN HOUSTON. WHILE WORKING ON A PROJECT WE BROKE SOME INTERCOM SPEAKER BOXES AND I RPLACE THEM. I WOULD LIKE TO IF SELL THESE INTERCOM SPEAKERS.
➡️ Reply
#Rittenhouse by Karen Noll on 2009-11-16 14:27
I am looking for a cover to Rittenhouse, model 912 (possibly 812, numbers are difficult to read). Can you help?
➡️ Reply
#Rytec by Rick Martin on 2009-11-18 07:51
I have a TCP-101 Rytec roll-up door control unit that has a shorted power input. Can you give a ball-park estimate for repair? No rush, I have a spare. Sorry, but due to spammers my email is generic until I decide to work with you.
➡️ Reply
#Robinair by Lou Pennacchia on 2009-11-30 22:45
Hello, I recently purchased a Robinair Lectra-Torch, Model No. 14492, in what appears to be un-used condition. I have not tried to power it up yet. Would you be able to spare the time to let me know if this has any value? I will most likely list the item on ebay. Respectfully, Lou
➡️ Reply
#Rittenhouse by Jeff Swiger on 2009-12-09 21:38
I would like to replace my working existing RMC-4 rittenhouse intercom with a compatible unit. While using the existing wires? Suggestions _ and would you be interested in the old unit and speakers - 8 + 1 doorThanks,
➡️ Reply
#Rittenhouse by Deborah Braid on 2009-12-14 16:48
I have an old rittenhouse 7021 (I think) it is from 1978. It needs a new from cover and the dial to change the stations doesn\'t work. Otherwise it works. Can it be fixed and about how much?
➡️ Reply
#Rittenhouse by Charles Rose on 2009-12-22 23:34
Need base station repaired. Would purchase old
➡️ Reply
#Rittenhouse by Mary Anne Fuscaldo on 2009-12-25 23:04
I moved this door chime/clock when it was working from one home to another. The electrician that hooked it up did not do it correctly and I have no schematic for how it should be wired. I know it needs three wires but not sure on which of the 7 screws they get wired to. They do not indicate Com or T...
Show More
➡️ Reply
#Rittenhouse by Brandon on 2010-01-02 05:17
Please contact me about the cover of the door chime Model c8204.We lost it during repainting the wall when we moved in 2 years ago.ThanksBrandon
➡️ Reply
#Rittenhouse by Wendy Morris on 2010-01-15 06:14
Our current cover is kind of an almond color. After remodeling our living room, all of the vents, outlets, etc. have been done in white. Would it be possible to purchase a white cover to replace the almond one for our door chime? What would the cost be?Please respond even if not available before I r...
Show More
➡️ Reply
#Rittenhouse by FLORENCE LUM on 2010-01-22 03:42
Is there someone in Honolulu, HI whom I can contact to test and repair my intercom, and replace my ON/Off switch @ the MASTER SPEAKER?We have enjoyed our unit for many years, since 1968.
➡️ Reply
#Rittenhouse by O. H. Towers on 2010-01-25 16:00
We are also electrical contractor company(Towers Electrical Serv. Inc)We are looking for a model C8931 R Chimer Receiver also a sender unit if possible.We cannot find any info on this item it was made ty Rittenhouse Fayettevilole, nc. 28302
➡️ Reply
#Rittenhouse by sue wardy on 2010-02-22 15:07
static, fade in and out radio. intercom doesn\'t work but don\'t care about that just want the fm on radio to work more consistently
➡️ Reply
#Rustronic by simon Jackson on 2010-02-22 16:47
Hi Please could you quote me price and delivery on a Rustronic 4509 vibration card.Kind rgeardsSimon Jackson
➡️ Reply
#Rittenhouse by ann chamberlin on 2010-03-07 15:43
Jennifer Walker:Did you ever figure out what to do about replacing your Rittenhouse unit? I\'m in the same boat!Any ideas or products you have come across on your own would be appreciated
➡️ Reply
#Rittenhouse by colleen on 2010-03-10 04:32
i have a model 7035 that was removed from the wall to repair the wall. Now I need to reconnect - but don\'t know how the wires go together. Are there any instructions available?
➡️ Reply
#Rittenhouse by william junker on 2010-03-20 16:08
I need a replacement part for this devise.
➡️ Reply
#Rittenhouse by Bob Hilsher on 2010-03-27 16:29
Unit stopped working. Have 16+ volts coming to it but no sound. Assume the syncronous motor is out... Telechron model M3151, Type H18, 3.6 rpm, 60 cy, 16 v. Is the replacement motor available? Price?Could it be anything else? All wiring is in tact on board.Thanks, Bob
➡️ Reply
#Reta Electronic by Floyd Smith on 2010-03-28 12:39
Model 5200 DC Drive we need a user manual
➡️ Reply
#Rittenhouse by randy connelly on 2010-04-12 00:59
I need a Rittenhouse door bell botton part number C8000. Is this womethign you may have?
➡️ Reply
#Rittenhouse by Diane Reichard on 2010-04-14 13:54
Hello! Do you have any parts for Rittenhouse (Emerson) All Transistor Radio-Intercom System, Model RM-1 (AM radio) or RM-2 (AM/FM radio)? Our system dates from the 1960\'s--still going strong. But I need knobs and especially the instruction manual because I don\'t know how to answer and use the exte...
Show More
➡️ Reply
#Rittenhouse by Jim on 2010-05-01 22:41
I have the above model doorbell and really like the sound vs. the new \"electronic sound\" doorbells. Problem is the mechanism inside the doorbell (the part with the two knockers that the wires attach that hit the bells to make the sound) no longer works. Can I still get this part replaced...
Show More
➡️ Reply
#Rittenhouse by DANNY on 2010-05-06 16:48
I AM A ELECTRICAL CONTRACTOR AND HAVE BEEN TOLD THAT NUTONE WILL WORK USING EXISTING WIRING THE PROBLEM IS NUTONE WILL NOT WARRANTY IF YOU DO NOT USE NUTONE WIRE, BUT THEY DO HAVE A 30 DAY RETURN POLICY TRY THE SYSTEM IF IT DOES NOT WORK TAKE IT BACK ASAP
➡️ Reply
#Rittenhouse by Jessica Rasmussen on 2010-07-17 03:18
I get typically one of three chimes to sound when the doorbell is rung, occassionally 2 followed by a buzzing sound. Some of the wires were loose and I tightened them, but still don\'t get all the tones. Any ideas on what to do to get all three chimes to ring?
➡️ Reply
#Rittenhouse by Jessica Memmott on 2010-07-22 18:45
My model 552 is not working. Licensed Electrician checked it out and it need replacement parts. I want to keep actual doorbell, because of sentimental reasons.
➡️ Reply
#Rittenhouse by Robert King on 2010-08-02 01:52
I know this chime assembly is very old but is there a replacement kit for the hammers. they are sticking and perhaps the springs are just too soft. I\'d appreciate any help you can give me.
➡️ Reply
#Reta Electronic by Ahmet Ýsmail Soylu on 2010-08-04 15:28
Hello, My company is BAYCAN Chewing Gum and Food Ind. and we are a member of Turkey\'s one of the biggest group ULKER. In our chewing gum wrapping machines ( Rose Theegarten ) your inverter D 52 is used and I need it\'s user manual to see the functions of the adjustment screws. so could you send me ...
Show More
➡️ Reply
#Rittenhouse by A.L. Richard on 2010-08-09 13:32
My home was built in 1965 with the same Rittenhouse intercom/radio system that doesn\'t work anymore. I would like to upggrade with intercom/radio/ satellite radio system can you do the work? What would be the estimated cost?
➡️ Reply
#Rittenhouse by R.Sarin on 2010-08-11 23:11
Hi I need a cover for the rittenhouse door chime model 380 can u pls get back to me thank you
➡️ Reply
#Ratelco by KEN REDEKER on 2010-08-17 20:40
Advise P&D to repair Ratelco Model# 102B03504-00 battery charger
➡️ Reply
#Reta Electronic by Jayantha Kumar TP.No: +94-718799943 on 2010-08-26 08:44
Dear SirWe are request for Reta Electronic drive Type 531-20Pls send me a questions.Thank YouJayantha KumaraElectrical EngineerCentral Industries PLCNo:312, Nawala Road RajagiriyaSri Lanka Phone:+94-718799943
➡️ Reply
#Rustronic by Mellah on 2010-09-11 15:56
Bonjour, Monsieur;Afin de me permettre de lire les modules du software, et de bien comprendre le fonctionnement des turbines installées à notre site Sonatrach, j\'ai besoin de m\'envoyer un document qui explique les instructions utilisées dans des modules par exemple ( /*DEF: MODULE:TURBINE_GAS_FUEL...
Show More
➡️ Reply
#Rittenhouse by Bill Chellberg on 2010-09-18 22:20
What transformer do I need for this?Thanks
➡️ Reply
#Rittenhouse by J. G. Colbert on 2010-09-28 22:30
The rheostat is broken on this unit otherwise the unit is as melodious as it was 40 years ago.The numbers on the rheostat are 1406417 and 135-51 The motor is a Telechron synchronous motor. 118V--16 Model 3151 RPM 3. W. 4.CantI purchase the replacement rheostat and have it shipped to PMB 399 at the a...
Show More
➡️ Reply
#Reta Electronic by MOHAMMAD MEHDI ALLAHYARI on 2010-10-07 06:07
we need catalogue and drawing about dancer cotrol type:reta electronic 5200 sigburg bv 70/5-39tank you for help us.
➡️ Reply
#Rittenhouse by paul caley on 2010-10-09 16:33
plungers have stopped (tried lube) is model w clock can they be replaced by myself or must this be done by a pro or can the entire panel be more easily replaced thank you
➡️ Reply
#Robinair by Gaston Soliz on 2010-10-11 21:53
I require the carbon contact blocks that mounts on the soldering tongs of this soldering device. Please indicate how can I proceed to obtain at least three sets of each , your price, possible delivery date and form of payment.
➡️ Reply
#Robinair by Gaston Soliz on 2010-10-11 23:08
Please quote two pairs, each, of Electra-Torch carbon tips ,Part No 14492-50. Please indicate were you will deliver, posible delivery date, and form of payment.Please answer ASAP. Thanks G.Soliz
➡️ Reply
#Rittenhouse by Diane McCracken on 2010-10-26 15:22
Do you sell parts? I am looking for a replacement potentiometer for an Emerson-Rittenhouse RC 633. It is labeled Clarostat 140-6747/ 135-51.
➡️ Reply
#Rittenhouse by Cyndi Taylor Krier on 2010-11-17 22:19
Can I order a replacement transformer for this doorbell from you?
➡️ Reply
#Rittenhouse by Norm Negus on 2010-12-02 00:14
Hello I have a Artolier Lighting and Sound Emerson Electric Co. Model C8535 the springs need replacing can you please Help thanks Norm
➡️ Reply
#Rittenhouse by David Strodel on 2010-12-05 00:34
Hi, I have a Rittenhouse 330 Chime that is not working. Is there a way to get a rough estimate of cost? It may be the transformer or the hammers as they are sticky.David
➡️ Reply
#Ratelco by thom fischer on 2010-12-10 03:13
120vdc to 120vac 60hz 1.0kVAour bard is fried, need new one asap360-739-9777thom
➡️ Reply
#Rittenhouse by Larry Graham on 2011-01-02 02:03
I am looking for a wiring diagram for a Rittenhouse, Spartan Electric, Fayettevile NC C8845 unit which is 30 to 35 years old. It seems to be either able to use two D cells or 16V transformer but I am got sure how to wire it up. Any ideas? Thanks.
➡️ Reply
#Rittenhouse by Billy Hubbard on 2011-01-02 16:44
The Rittenhouse door intercom answering system system was installed in 1978. It is not functioning well. Do you have a newer replacement for it that would still have the doorbell and intercom system? Does a new unit come with the exterior speaker?
➡️ Reply
#Rittenhouse by MARK WILSON on 2011-01-12 14:35
This is a Mechanical doorbell with Electronic Control Board. I need Someone to give me an estimate for repair or tell me where I can get parts for this device. Thanks, Mark Wilson
➡️ Reply
#Rustronic by wahalim on 2011-01-13 05:12
We have few unit cards CT91002/2 need to repair.Pls estimed cost repair and delivery.Few CT91002 components burnt
➡️ Reply
#Rittenhouse by Art on 2011-02-07 18:45
My dad just passed away and I\'m moving his Rittenhouse Westminster clock/chime from his place to mine before selling the house. I believe it is a model 631 or 632 but I\'m not sure - WHERE CAN I FIND THE MODEL NUMBER? (I\'ve seen pics of what appear to be identical units labeled 631/632).I\'ve got ...
Show More
➡️ Reply
#Rittenhouse by Eric Zetterberg on 2011-02-11 19:49
I have three doorbells connrcted to chimes but only one works, any suggestions?
➡️ Reply
#Rittenhouse by Roy Snelgrove on 2011-02-24 02:47
The door chime is not working properly in that some of the hammers are not striking properly. sometimes they reach the tubes and sometimes not. They are all active but not as strong as they should be .I have turned down the adjuster and none strike and when turned up, it is as I have described . The...
Show More
➡️ Reply
#Rittenhouse by Marcy Berry on 2011-03-03 21:25
I am a property manager who manages a townhome with a broken Rittenhouse intercome system. The speakers on the exterior are installed in the brick so to remove them is a huge project. The main console in the kitchen is what I am looking to repair or replace. The model number is: (looks like) M7034. ...
Show More
➡️ Reply
#Rittenhouse by john rohter on 2011-03-03 21:43
Looking for instruction for the door chime opporation.
➡️ Reply
#Rittenhouse by Christopher Cruz on 2011-03-09 13:15
Hellohave a 520 Beverly and it is working but I took it apart and found the rubber grommets and the felt strike pads are bad i am looking for replacements.ThanksChris
➡️ Reply
#Reta Electronic by Barry Keech on 2011-03-10 07:24
I too am looking for a manual to connect and set a D5200 DC drive that I have just recieved in equipment that I must recommission.Did you recieve any information that could help me to connect and operate the drive? I would appreciate a copy if you have a connection manual.
➡️ Reply
#Rauland-Borg by Roger Hightower on 2011-03-10 19:16
Can you repair station cards from Rauland intercomsystems? Part #TC2113??RH
➡️ Reply
#Rittenhouse by Yale Wolff on 2011-03-15 15:01
Have a Rittenhouse intercom system installed in 1956. There appears to be a dead short in the Master.Is there a NuTone Master AM/FM which will work with the satellite room units?
➡️ Reply
#Rittenhouse by Tom Gleason on 2011-03-31 01:27
Looking for a sequencer box for a model 552 doorbell chime. I know they are rare. Does somebody make a retro fit or do you have a good used one. If none of the above then how about schemetics and I will get one made. Thanks-Tom
➡️ Reply
#Rytec by Ghislain Dufour on 2011-03-31 11:44
we have here a rytec control board and search for somewhere to have it fixedthanks for the support.
➡️ Reply
#Rittenhouse by Roshan on 2011-04-18 18:17
I have an old Rittenhouse intercome unit, since I don\'t use it that much, I would like to replace the face of it with something newer, don\'t know if it;s possiable? please let me know how i can do this.
➡️ Reply
#Ratelco by Tony Pyle on 2011-04-18 19:11
Have two chargers type FC24754 Model 102B-3602-03 Ser# 8741252My Batt Charger # 1 has been charging a lead acid bank for the past 4 years. AMG 8A8DLTP 245amphr (12vdc x 4 battery) and the AC fail light has been on as I am told for years. Batterys have gone bad and going to replace them. Question at ...
Show More
➡️ Reply
#Rittenhouse by Colleen Wilkowski on 2011-04-28 15:24
I am searching for a User Manual for the Rittenhouse M9041 AM/FM Radio-Intercom system. The unit is original to the house built in 1982. I have found a tech manual with schematics but now need to locate a User Manual. Any suggestions would be appreciated. Thanks.
➡️ Reply
#Rittenhouse by Steve on 2011-05-01 18:27
need diagram for wiring of C8203. Only two reds, 2 whites, where would transformer lead be?
➡️ Reply
#Reliance by Ivan Molina on 2011-05-02 00:00
Reliance 120245 not powering on, no display or response. Need immediate repair service, please contact ASAP.
➡️ Reply
#Rittenhouse by Lynn Villano on 2011-05-06 13:29
but want door bell to continue working. Can we get wiring schematics?
➡️ Reply
#Reta Electronic by muhammad shafaat on 2011-05-11 09:37
Dear Sir,Please qoute for the following item Electronic PCB of DC Motor Drive.TYPE: 531-21CARD: BV 7072-86QTY: 02At yr earliest.Best Regards,(ENGR: MUHAMMMAD SHAFAAT)DY. GENERAL MANAGER (WEM)PAKISTAN INTERNATIONAL AIRLINESKARACHI PAKISTANTEL: 92-21-99045159
➡️ Reply
#Rittenhouse by miriam spear on 2011-05-16 14:13
Only one of four chimes works, although we detect a faint electronic buzzing, in sequence, of the other three. For example, we hear Chime A, buzz, buzz, pause, buzz, buzz, Chime A. As cover has been lost, we suspect dust and grime is keeping the other hammers from working.Can the unit be cleaned and...
Show More
➡️ Reply
#Reo Elektronik by Neil Macalister on 2011-05-18 05:32
Do you have a service breakdown drawing for the SOR6 control box also the P/N and P&A for the supply boardRegardsNeil
➡️ Reply
#Rittenhouse by Fred on 2011-05-25 04:18
Art - did you get a reply in answer to your post?I am about to restore the same door chime, you may have info that can help.ThanksFred...
➡️ Reply
#Rittenhouse by Virginia Melchi on 2011-05-25 22:34
Purchased a use Rittenhous Westminster door chime / clock; Tetechron Motored, model #8633. I need a wiring diagram for this unit.Thank you,Virginia Melchi
➡️ Reply
#Rustronic by Magnus on 2011-05-29 19:57
Hello! I\'ve got problem with my washing mashine. That\'s alert E90 about 15 seconds after I pushed the start button och nothing else is happend. DATA:Precond elettronica type 451516811Type E.Z Assembly: 132191552Type E.Z Board:124307062SW Ver.:UDA30202T70 WK:52/05 Op:4410
➡️ Reply
#Rytec by Wayne Medeiros on 2011-06-03 23:40
We just installed 3 Rytec Predadors with the Feig Encoders , 1 Door worked fine 2 do not have communications with the controler. Rytec support claims the wire is bad , we replaced the wire but left it at full lenght with no change , the door that works has the full lenght of cable thus making me bel...
Show More
➡️ Reply
#Rittenhouse by Don Pieschel on 2011-06-25 22:05
I have a RM-2 or a M9401 rittnhouse intercom I need a manual or schematic.any ideas where to locate.Don
➡️ Reply
#Reta Electronic by Adritec SA on 2011-07-08 09:15
We need a manual for setup and fault related drawings on this drive
➡️ Reply
#Rittenhouse by Candy Cicoria on 2011-07-14 01:45
I recently moved into a house that has the Rittenhouse All Transistor RCM-1 system in every room. It\'s obvious this system has not worked in a few years, but I want to repair it and keep it with the time of the home. A newer system would take away from it\'s appeal. Is there anyone in the Tulsa, OK...
Show More
➡️ Reply
#Rittenhouse by Mark Ivess on 2011-08-01 00:00
Hey there, I've been tasked with looking into an issue with a Rittenhouse C8578-1 135-7351-01 door chime. I don't usually work on hardware like this, so I could really use some guidance on how to fix or replace it. Any help or advice you can provide would be greatly appreciated. Thanks in advance!
➡️ Reply
#Robotool by Bob Challes on 2011-08-04 00:51
Cannot Autohome X Axis switch is open
➡️ Reply
#Rittenhouse by carolyn berkey on 2011-08-04 23:15
our unit has power and the light comes on but nothing works. The electrician says it is not the transformer.
➡️ Reply
#Rittenhouse by TONY HOVANEC on 2011-08-09 16:09
HAD LIGHTNING STRIKE AND WOULD LIKE TO REPLACE IF YOU HAVE A RETRO UNIT TO REPLACE IT THANK YOU
➡️ Reply
#Rittenhouse by paul najarian on 2011-08-11 21:58
We\'ve got an old aprox. 30years old unit. signal fades in and out. Best to try and repair or do you sell new/updated maybe with cd or mp3 imputs? Also need a external outdoor speaker/intercom box. Has the 5 plug cupling. thanks,Paul
➡️ Reply
#Rittenhouse by tony on 2011-08-16 17:00
where can i find rittenhouse intercom/radio part??
➡️ Reply
#Rowan Elettronica by Jim OBrien on 2011-08-18 00:00
Rowan Elettronica 280/93 3-phase drive not responding to input commands. Need immediate repair assistance to get production back on track.
➡️ Reply
#Rittenhouse by Jim Romeiser on 2011-08-18 07:20
My Rittenhouse door chime\'s top plunger does not work, the previous homeowner said when he was hooking it up, by accident the top soleniod was getting power all the time and over heated and it has not worked right since... can this be fixed ????
➡️ Reply
#Rittenhouse by Franklin D Bamsey on 2011-08-22 12:52
Push the outside button and the bell does not work. It has been in the house since it was build in 1988. Any suggestions?
➡️ Reply
#Rvsi by Alex Loo on 2011-08-23 09:06
Dear Smith, We can do 1 - 1 exchange your old defective unit with a refurbished unit.Let us know.Thank youAlex LooGlobal Semicon Technology Pte LtdEmail : alexglobal@singnet.com.sgEmail : alexglobal63@yahoo.com.sgMobile : +65-9002-7838Tel/Fax : +65-6476-3568Skype: alex.loo63
➡️ Reply
#Rittenhouse by Franklin D Bamsey on 2011-08-30 18:30
I have an Emerson Door Bell C 8204 and it is not working. Need a response to this E- mail please.
➡️ Reply
#Rittenhouse by sheila on 2011-09-05 18:24
Would you know where i can find a C8931R?
➡️ Reply
#Rittenhouse by karen varel on 2011-09-07 00:53
Do you sell parts for rittenhouse dooor chimes specifically Model #C8550 or do you know where I can get them?
➡️ Reply
#Rittenhouse by Michael Senay on 2011-09-08 17:07
My rittenhouse chime is about 15 years old and I would like to get it repair. I would like to know who can repairs it.
➡️ Reply
#Rittenhouse by charles thomas on 2011-09-14 17:53
I need to purchase a new door bell system comparable with the existing system. I have a one unit on the main level and the other in the basement. The Model number of the existing system is C8203 16 volts AC. I need both units to include outside switch. Also where are the transformers located for thi...
Show More
➡️ Reply
#Rittenhouse by JENNIFER SMITH on 2011-09-21 15:16
I have a Ritten House Model 620R that needs to be repaired. The chimes are off of it and I have the motor ?? and clock box just needs to be put back together. I would love to have this repaired for my husband. We came across this clock out of a rental house we own and very sadley our renters damaged...
Show More
➡️ Reply
#Reta Electronic by LABAERE PASCAL on 2011-09-23 13:55
HELLO I HAVE A DRIVE D52 SIEBURG BV532/25-13.2BUT I NEED INFORMATION ABOUT MOUNTING AND PROGRAMMATIONCOULD YOU PLEASE TRANFERT THE MANUAL OF MOUNTING AND PROGRAMMATIONTHANK YOU FOR YOU HELP
➡️ Reply
#Rotaprint by faiyaz husain on 2011-09-25 05:25
please send me complete wiring diagram / wiring scheme of Rotaprint ttr2 printing machine by email.thank you!
➡️ Reply
#Rittenhouse by Doug on 2011-10-01 20:21
I currently have this unit for sale on ebay. the wiring is simply two wires from the 16v transformer to the appropriate screw terminals on the printed circuit board and then the \"switch leg\" from each door bell button at the doors you are using attached to the corresponding terminal scre...
Show More
➡️ Reply
#Rittenhouse by Anthony Butts on 2011-10-02 19:14
The unit works, but possibly in need of some service. The AM radio works , but no FM. There is a bit of background noise in the system.
➡️ Reply
#Rittenhouse by Anthony Butts on 2011-10-03 12:46
The unit works, but possibly in need of some service. The AM radio works , but no FM. There is a bit of background noise in the system.
➡️ Reply
#Rittenhouse by stan j korzinski on 2011-10-14 21:39
model c8550 8 note melody needs motor
➡️ Reply
#Rittenhouse by Linda La Bruna on 2011-10-16 18:45
I have a Ritten House RM-2 Radio Intercom in original box with original instruction booklet AND an OR-11 Outdoor Remote Station I am looking to sell.If you or someone you know would be interested, please contact me.
➡️ Reply
#Rittenhouse by Jo Ann Redmond on 2011-10-18 23:20
Good Evening,We have a Rittenhouse Intercom System (solid state Am/FM Radio Intercome) it has got to be at least 30 years old. We are looking to replace the outside speaker box (Nu-tone). Please let us know if this item is still available. We would give you more info on the system, but cannot find s...
Show More
➡️ Reply
#Rittenhouse by craig cipriani on 2011-11-03 15:22
I hav a door chime and clock rittenhouse model 631 and 632 i need a wiring diagram for. any help i can get is appriciated thank you
➡️ Reply
#Rotaprint by darko luksic on 2011-11-11 09:46
Please send me complete diagram and scheme elektrical of rotaprint 35 ofset machine by mail.thank you
➡️ Reply
#Rittenhouse by sonny sadler on 2011-11-21 16:12
i would like to have an updated model the one i have was installed in 1977 it makes noise, drifts off stations all controls are noisey and sound is garbled. can you tell me where to get help.
➡️ Reply
#Rittenhouse by Gord on 2011-11-24 21:00
Jessica:I have the same model door chime, with the same problem. How did u make out with yours? Do you know any of the history of this chime. From what I can surmise, it was produced after WW2 and that would fit as it was in my parents house when i was born in 1954. I have a friend that is an electr...
Show More
➡️ Reply
#Rittenhouse by Ray Smith on 2011-11-29 00:44
very low sound no door chime
➡️ Reply
#Rittenhouse by John Erlinger on 2011-12-01 21:30
It appears the hammers are sticking or a spring has broken. There are three. Can i get replacement solenoids/hammers, or an estimate to repair the whole Chime unit. Also if you think it would be best to buy new.Thank you.,John
➡️ Reply
#Rittenhouse by Jeff Picha on 2011-12-05 14:24
Hello, I have a customer that brought in a door bell unit, the one of theplungers is bent inside. I do not know alot about these things, we work on electric motors. He want to know if he can still get parts for these unit.The model # is c8231. Please inform, I may just send him your way. Thanks for ...
Show More
➡️ Reply
#Rittenhouse by David Hocevar on 2011-12-05 17:56
I have a ritenhouse emerson door chime unit. It just started chimeing for no reason I had to disconnect it to silence it. Now when I hooked it back up nothing happens. Clock doesn\'t work, chimes don\'t work.Model 086331 4 tubed chime It also has a teledcrome syncronis motor. Any hope for it.Thank Y...
Show More
➡️ Reply
#Rittenhouse by joe Delle Dinne on 2011-12-20 00:25
I would like to know if spare components are still available? eg transistors and LM283T 5 pin audio amp or regulator? Or is there a replacement UNIT and what is the cost for a compatible unit.
➡️ Reply
#Rittenhouse by Ellen on 2011-12-23 17:22
The installation manual has been misplaced and I am not sure which wires go to which connection. There is a red wire, a black wire, and a yellow with a green wire. The places to connect are for the front, rear, and transformer. Please advise. Also, there is a possibility that the transformer doesn\'...
Show More
➡️ Reply
#Rittenhouse by jim Snyder on 2012-01-12 05:28
A friend of mine has a doorbell that i am hoping to repair and would like to find the wiring diagram for it if possible. The only tag I can find on it saysArtolier Lighting & Sound Div. Emerson Electric Co. Rittenhouse Operations Honeoye Falls NY 14472 Model RC203 or RC208 Volt 10 There are thre...
Show More
➡️ Reply
#Reta Electronic by Luyanda Sidumba on 2012-01-13 06:08
I have a reta laboo TSR 4Q85 drive, I would like to know if you can give me a qoutation on the new Dc drive of the same kind.
➡️ Reply
#Rittenhouse by Eric Schneider on 2012-02-04 21:58
Do you know where I can find the outdoor part you push to ring for this Emerson Model C8203? Thanks for your time.Eric Schneider
➡️ Reply
#Reta Electronic by chiranjib bera on 2012-02-13 23:47
sir,i have so many reta electronic drive different type. i need manual of drive type 531-22. of reta electronic. you are requested to send the manual in pdf or word format of my email.regards,chiranjib beraasst managerphoenix coveyor belts india lts
➡️ Reply
#Reta Electronic by dave francis on 2012-02-14 15:46
please send me a manual please.
➡️ Reply
#Robinair by ALAN W. PILGRIM on 2012-02-26 20:17
I HAVE AN OLD LWCTRA TORCH THAT HAS DONE A LOT OF WORK, BUT NOW THE TONGS HAVE COMPLETELY WORN OUT AND NEED TO BE REPLACED COMPLETE WITH CABLES. CAN YOU ADVICE ME ON HOW i CAN OBTAIN THE ITEM AND THE COST.THANK YOU.ALAN PILGRIM.
➡️ Reply
#Rittenhouse by Corinne Censulla on 2012-02-29 17:56
I have a very old doorbell/ clock combination. The Model # is 450. The chimes work but not the clock. Since it is installed into the wall is there one the will replace using the same insert?
➡️ Reply
#Robinair by ALAN W PILGRIM on 2012-03-06 11:53
I NEED A COMPLETE TONG, CABLE AND CARBIN SET TO REPLACE MY OLD WORN OUT TONG SET. PLEASE CAN ANYBODY HELP ME?
➡️ Reply
#Robinair by ALAN W PILGRIM on 2012-03-06 11:55
I NEED A COMPLETE TONG, CABLE AND CARBIN SET TO REPLACE MY OLD WORN OUT TONG SET. PLEASE CAN ANYBODY HELP ME? MANY THANKS,ALAN.
➡️ Reply
#Rittenhouse by Richard Baer on 2012-03-06 23:58
This unit puts out a chirping sound (Similar to sound of a smoke alarm) on a continuous basis, one chirp about every 30 seconds. Please advise what I should do, short of disconnecting the unit, to stop this annoying sound.Thank you,Richard Baer
➡️ Reply
#Rittenhouse by Eddie Ellis, Jr. on 2012-04-02 22:38
I have a Rittenhouse / Emerson intercom system with individual stations for each room. Two of the intercom speakers nolonger work. When I opened them they have one red, one yellow and one black wire leading from the unit. Is it possible to get them worked on or replaced. They measure 8 3/4\" lo...
Show More
➡️ Reply
#Rittenhouse by Terri McDougall on 2012-04-06 14:55
Our house was built in 1978 and we purchased it in 1997. It had the Rittenhouse monitor system in place with the main unit in the kitchen and smaller units scattered thought the house and in an attached apartment. The unit has never worked since we have been here and I was wondering if it is repaira...
Show More
➡️ Reply
#Rittenhouse by Edith Whitaker on 2012-04-10 15:32
some unit owners intercom is not working, needs repair. Who can we call on this?
➡️ Reply
#Rittenhouse by Withgott on 2012-04-13 00:00
Having issues with my Rittenhouse RCM-4 intercom with radio - the radio feature is not working. Need repair assistance
➡️ Reply
#Rittenhouse by Tony Falco on 2012-04-17 19:38
Do you have available a manuel for the emerson ritterhouse RCM-4 intercom. I have to re- install mine
➡️ Reply
#Rittenhouse by Joe on 2012-04-18 13:36
Could you please direct me as to where I may be able to obtain a circuit diagram for a rittenhouse installed in the 1980?Many thanksJoe
➡️ Reply
#Rittenhouse by Tedd Boomershine on 2012-04-22 21:49
The clock works fine. Three of the door chimes work, but the fourth and fifth strikers do not work. Do you repair and or have parts to recondition? Thanks, Tedd
➡️ Reply
#Rustronic by Muhammad on 2012-05-09 15:45
Need Control Logic (Digital and Analog) of Rustronic MKII
➡️ Reply
#Rittenhouse by Mark Hefner on 2012-05-18 01:33
I have a emerson rittenhouse rcm 4 main unit with IR6 speakers throughout a house i purchased and am interested in upgrading the entire system. Is there a replacement system where it can be changed out?It will be a few months before I am ready to do it, but am trying to look at options and replaceme...
Show More
➡️ Reply
#Reo Elektronik by James Dantonio on 2012-06-01 18:47
Hello I\'m a mechanic for Watson Pharaceuticals in Copiague long Island. I have 2 -REOVIB MFS268 Frequency Controllers that are in need of repair. I was wondering if its possible for you to email me a quote on refurbishing these units!! Thank You!! Jimmy.PS Do you take credit cardseither ways no pro...
Show More
➡️ Reply
#Rittenhouse by Michael Donnelly on 2012-06-05 13:26
HiI have the above chime box and wish to re assemble it. I took it down for decorating purposes.There is a black/dark blue wire, a yellow wire and a red wire. There is trans, front and rear. My question is what wire goes with what?Many thanks Michael Donnelly
➡️ Reply
#Rittenhouse by Ken Selinger on 2012-06-06 02:03
We have an older intercom system M9325 stations, M9318, and M9322. We are wondering if there is anything we can do to reduce the standing hum.Thanks
➡️ Reply
#Rittenhouse by Joseph LaBarbera on 2012-06-11 14:33
Would like to know if there is a replacement for this unit or where I can find a replacement knob for the Talk Listen stalk.
➡️ Reply
#Reo Elektronik by Lee Benson on 2012-06-27 13:55
Dear Sir,We do have one REO thyristor controller needs to repair.Can we first send you the damaged photo for the reference?Please kind to provide the e-mail address.Thanks.BR,Benson
➡️ Reply
#Rittenhouse by Qaiser Baig on 2012-07-01 04:25
Hi,Some one open the wires of my door bell Model C8550 (in the bell). Would you please give the wiring/connection diagram for this door bell so that I can re-connect the wire to operate my door bell.You co-operation & early response will be highly appreciated.Regards,Qaiser Baig
➡️ Reply
#Rittenhouse by Gary Bowles on 2012-07-17 00:01
Need a wiring diagram to an intercom with a doorbell.Artolier Lighting & Sound Div.Rittenhouse OperationsHonoye, NYmodel: M7034serial: (stamped) 202 (hand written) 0 2234-1748The intercom is powered by a 16 volt transformer on a closet wall. The standard 2-tone doorbell is in the hall. The base ...
Show More
➡️ Reply
#Rittenhouse by Albert M. Brien on 2012-07-29 04:52
I have an older system, it was still working but when a water pipe broke behind my kitchen wall, it soaked the unit and ruined it. I want to know how much it would cost to have it replaced so I can get back the intercom and music function. Thank youAlbert Brien
➡️ Reply
#Reta Electronic by Miler Bela on 2012-08-01 14:55
Hello,I have a thyristor drive BV 522/10 but dont have manualls so dont no whatpotmeter can conectid and the power of taho.If you can help me send e-mail.Thanks and best regards Bela
➡️ Reply
#Rittenhouse by Glenn Loiselle on 2012-08-09 11:51
I have a circa 1977 Artolier Lighting and Sound door Chimes / door bell / wall clock that HUMMS all the time. MODEL # C8633Can it be repaired?
➡️ Reply
#Rittenhouse by Glenn Loiselle on 2012-08-09 11:58
I have a circa 1977 Artolier Lighting and Sound door Chimes / door bell / wall clock that HUMMS all the time. MODEL # C8633Can it be repaired?
➡️ Reply
#Rittenhouse by edward havertong on 2012-08-11 17:33
I TOOK THE CLOCK TO A ANTIQUE DEALER HE TOOK THE MOTOR OUT AND REPLACED IT WITH A BATTERY UNIT. I AM LOOKING TO REPLACE IT BACK WITH THE ORIGINAL MOTOR.
➡️ Reply
#Reta Electronic by kamran on 2012-08-22 06:07
i need user manual
➡️ Reply
#Reta Electronic by kamran on 2012-08-22 08:13
i need dc drive manual
➡️ Reply
#Reta Electronic by kamran on 2012-08-23 07:55
please send to me BV 531/200L-21-02
➡️ Reply
#Reta Electronic by KEITH DICKINSON on 2012-08-30 07:22
WE HAVE A RETA BV 524/28-15-2 DC DRIVE WITH OPTIONAL PRESET SPEED INTEGRATOR. WE NEED TO MAKE SOME ADJUSTMENTS TO THE DRIVE BUT DO NOT HAVE A USERS MANUAL, SO DO NOT KNOW WHAT POTS TO ADJUST. ALL DRIVE PCB MARKINGS ARE IN GERMAN.CAN ANYONE HELP?ANY ASSISTANCE WILL BE GREATLY APPRECIATED.REGARDSKEITH...
Show More
➡️ Reply
#Rittenhouse by Mark Palmer on 2012-09-06 21:18
I have 2 Rittenhouse intercom speakers that need to be replaced. They both measure 9 1/4\" long. 6 1/4\" wide and 3 1/2\". Do yo have suitable replacements? If so, how much are they? Price of each unit, tax if aplicable and shipping charges for a total net price.Thanks in advance for ...
Show More
➡️ Reply
#Reta Electronic by maxim on 2012-09-10 13:28
i need manual of drive type 531-22. of reta electronic. you are requested to send the manual in pdf or word format of my email.regards,maxim from tmax electronic engineering ltd
➡️ Reply
#Rustronic by reza ramezani on 2012-09-26 14:15
Dear Sirwe need a copy of PLC and monitoring program for SGT-100-2s (Typhoon) MK II ; star fuel valve. we will be highly appriciate if you quote us the above software.best regards
➡️ Reply
#Rittenhouse by Earl Miller on 2012-10-11 01:03
Can I use the existing wiring and recessed wall areas of the old system listed above with a new replacement system. If so, what new updated system will work? Thanks
➡️ Reply
#Rittenhouse by Earl Miller on 2012-10-11 01:23
Is there a new updated unit (with new bells & whistles) that can use the existing wiring and wall recesses of the old units. If so, where can I get them and what would be a ballpark pricing? Thanks
➡️ Reply
#Rittenhouse by Howard Robertson on 2012-11-19 01:59
intercom system does not work.would like to have it repaired.
➡️ Reply
#Rittenhouse by Jim Fields on 2012-11-19 16:03
I have a schematic for Models M7010, M7011, M7012, M7020. The document also has AM Alignment, FM Alignment, Troubleshooting chart, and list of replacement parts for printed circuit board.
➡️ Reply
#Rittenhouse by John Zeitler on 2012-12-05 22:32
I am looking for the cover that is a black plastic 8 3/8\" wide, 5 1/2\" high, and 2 1/8\" deep. Any idea where I can find a suitable replacement? Thanks.
➡️ Reply
#Reliance by Donald Brown on 2012-12-09 00:00
Machine not powering on. Power light indicator is not lit.
➡️ Reply
#Rittenhouse by Don Meierhoff on 2013-01-01 10:50
Need a schematic for the Emerson-Rittenhouse Model rm20/rm22. Need to know transistor replacement numbers for the front end tuner.Thanks,Don
➡️ Reply
#Rexroth Hydraulics by Ian on 2013-01-15 00:00
The Rexroth Hydraulics MDC1-16 controller is displaying error code 3E-05 and is not responding to input commands. Urgently looking for a technician with expertise in troubleshooting and repairing industrial control units.
➡️ Reply
#Rotaprint by george tulea on 2013-01-19 18:03
please send me complete wiring diagram / wiring scheme of Rotaprint Rotogatte 24 printing machine by email.thank you!
➡️ Reply
#Rittenhouse by GUY DALFINO on 2013-01-24 17:30
I THINK I NEED A TRANSFORMER CLOCK WLL NOT RUN TX IN ADVANCE gUY
➡️ Reply
#Rittenhouse by Peter Taylor on 2013-02-15 23:47
I have a Ritten House Master Model 631 & 632 in my shop for repair. I would like to obtain a service manual for this item. Please advise if this is available. The clock is in bad shape as it fell of a wall and is in many pieces. Some of which I shall need to purchase.Please advise Peter TaylorTa...
Show More
➡️ Reply
#Rittenhouse by John Medina on 2013-02-22 19:58
Ubit was working fine, decided to hook up old style HI-FI unit per instructions and started blowing fuses. Looks like I created a short! Can you give me an idea of cost to repair and shipping charges? Thanks, John Medina
➡️ Reply
#Rittenhouse by James Short on 2013-02-24 20:40
A plunger on my 50 year old door chime is not returning to the rest position when the door chime is not activated. The consequence is a continuous buzz and erratic operation when the button is pressed.Have I provided sufficient information to diagnose the ease of repair?Thank you.Jim
➡️ Reply
#Rittenhouse by Mark Hefner on 2013-03-03 02:30
i am looking to replace my intercom system and looking for a new system to replace it with.
➡️ Reply
#Rittenhouse by Chuck Duncan on 2013-03-20 00:33
Was working well until I sanded and painted the kitchen. I took the chimes down to paint, put them back and nothing works. I get voltage coming in but it doesn\'t move anything.
➡️ Reply
#Rittenhouse by Chuck Duncan on 2013-03-20 00:35
Was working well until I sanded and painted the kitchen. I took the chimes down to paint, put them back and nothing works. I get voltage coming in but it doesn\'t move anything.
➡️ Reply
#Robopac by IN SIG JANG on 2013-03-21 02:42
Dear Sir,Our company location is South of Korea.We wish to buy Robopac\'s wrapping machine spare part from your company if possible. Would you please quote us for followings spare partsvery quickly.Wrapping machine spare partsModel: Helix HS30Serial NO:4111060194Slow roller \"PGS\" (code:5...
Show More
➡️ Reply
#Rittenhouse by Vev lee on 2013-05-19 16:43
I need the wiring digram for model number c8535
➡️ Reply
#Rittenhouse by Walter Powell on 2013-06-15 18:30
Front door button will only ring one time. Side door button will only ring one time. Want front door to ring two times (ding-dong). Don\'t see how to wire it right.
➡️ Reply
#Robinair by John Lemberg on 2013-06-25 07:13
I\'m looking for a price quote for a new power switch for the lectra-torch 14492
➡️ Reply
#Reta Electronic by K.D.C.L.Ekanayaka Ekanayaka on 2013-07-01 03:47
Dear Sir,I am looking for connection diagram or details of,RETA BV 70/2 - 84 DC DRIVECan you help me in this regard?Bst RgdsEkanayaka
➡️ Reply
#Robopac by john on 2013-10-11 06:02
hI, I\'m John Yang. I currentlty work for Meyer corp and we have 5 of your robopac 2002 model. We need a parts list or a diagram drawing so we can order some repaur parts. At this time we need to replace several front proxi switches, the one that detects the corners. Thank you please email me on how...
Show More
➡️ Reply
#Rittenhouse by STEVE on 2013-10-30 16:58
where can i find a schematic for a rittenhouse rm-20/22 intercom am fm radio
➡️ Reply
#Rittenhouse by bill whitacre on 2013-11-16 18:30
need to reconnect wires to front, rear & trans positions.
➡️ Reply
#Rittenhouse by patrick stark on 2013-12-05 15:48
need wiring, replacement parts and pic of the model noted above. front door pushbutton lights, but no response from chime unit. the backdoor is working normal one chime. What may be wrong? the unit has a selector switch to scroll thru various chimes.
➡️ Reply
#Rittenhouse by Morris Hoagland on 2014-01-05 03:53
My Rittenhouse Master unit has failed. Is there a replacement unit I can purchase?
➡️ Reply
#Rittenhouse by Brent Stoll on 2014-01-07 03:22
Label states Emerson Model S7671Rittenhouse DivisionArtolier lighting & soundEmerson Electric CoHoneoye Falls, New York 14472Second Label statesFire Alarm DeviceSingle and/or Multiple stationHome built in early 70\'s and have not found any information per this model and/ or type of device. If yo...
Show More
➡️ Reply
#Rittenhouse by P. Markworth on 2014-01-17 18:45
Do you know of anyone in Central or East Central Ohio who can repair a Rittenhouse electric door chime? It has four, short brass tubes and chimes like The Westminister chimes. Thank you.
➡️ Reply
#Rittenhouse by Bernard Zeifang on 2014-02-18 15:19
Please provide information needed to ship my unit to you for repair estimateand possible repair.I am assuming you need only the radio(master unit).Thank you!
➡️ Reply
#Rittenhouse by stan Mc Neely on 2014-02-21 17:39
some ONE TOOK MY 577 Apart, I need a picture of how the Chimes goback on the unitTHANKS
➡️ Reply
#Reta Electronic by atul on 2014-03-12 12:34
dear sir,please send me the dc drive manual for the type-531-22. we are based at south africa johannesburg.we are very big in recycling
➡️ Reply
#Rittenhouse by Richard Gilbert on 2014-03-13 02:02
Looking to replace the outside door bell speaker Mod. No.M9305
➡️ Reply
#Robertshaw by jason ritchie on 2014-04-08 00:00
Robertshaw 100-275-08A oven digital display not powering on or displaying any information. Need immediate repair assistance.
➡️ Reply
#Rittenhouse by Cathy Kirkwood on 2014-08-21 21:30
I purchased a home in Honeoye Falls, NY. It has an RCM 3 intercom that works and I would like to get a manual for it. Is it possible to get instructions for it?
➡️ Reply
#Rittenhouse by Patsy Goodwyn on 2014-09-27 23:39
We need to replace the long tubes on these chimes. They are look bad and we have lost one of them. Do you have the 4 tubes to replace the old ones with? If so, how much are they? Patsy
➡️ Reply
#Remco by Bobby Dillard on 2014-10-21 00:00
Remco 025-009460-00b 1804 01 circuit board not responding/powering up when connected to industrial unit. Need repair service ASAP.
➡️ Reply
#Rittenhouse by Dorothy \"Ann\" Imhoff on 2014-10-23 22:17
A Rittenhouse model 312 came with my home. It works but the chimes are not loud enough to heard unless you are in the room where the doorbell is mounted.I would hate to replace it because other than this it is very workable.
➡️ Reply
#Rittenhouse by Debbie Solovey on 2014-10-25 01:56
Hello, I am living in the house I grew up in and all of a sudden I noticed thatthe front doorbell was not working. The side doorbell hasn\'t worked for a long time. I have done some research so I will give you the information I have.Nutone Chime Signal, made in USA 1952, Model K 26 902 or 002It is a...
Show More
➡️ Reply
#Rittenhouse by Bob Murley on 2014-10-31 04:57
Is the volume of the chime adjustable?
➡️ Reply
#Rittenhouse by Krzysztof Charzynski on 2014-11-26 05:14
rittenhouse model 410 not working need repair
➡️ Reply
#Rittenhouse by Kirk Niatsikas on 2014-12-11 19:16
Do you have a rittenhouse rm5 manual?
➡️ Reply
#Rittenhouse by Frank Spramelli on 2015-02-10 19:04
needs repaired tuning dial is broken.
➡️ Reply
#Rittenhouse by Sandra on 2015-02-13 19:13
Our old doorbell cover on our doors is broken, how and where can we find new or different( maybe clear plastic cover) for the doorbell Thank you
➡️ Reply
#Rittenhouse by isagani l. cua on 2015-03-13 18:40
Sir: Please help me diagnose the problem of my C8204 door chime, andthis morning I heard a noisy sound from the unit. And please give menearest service center here in Chino hills, CalifornialThanks
➡️ Reply
#Rittenhouse by curtis gast on 2015-03-16 02:25
new home to me. system not working. any help would be great. thanks
➡️ Reply
#Rittenhouse by Ejschreier@hotmail.com on 2015-03-25 11:15
Lost during remodeling.
➡️ Reply
#Robotool by Carl Angell on 2015-04-14 18:18
Hi,We have a Robotool CVM1 that we are in the process of retrofitting. Could you give me the info on the following plug connections: J43, J518,J515 J52. We are converting to PC4CNC. The machine was working when we pulled the boards so if there is anyone in the market for them let me know. Any help i...
Show More
➡️ Reply
#Rittenhouse by Jorge Crespo on 2015-05-11 04:05
Riitenhouse chime model C8538R to connect into the AC adapter 16 volt .
➡️ Reply
#Rittenhouse by joe matthews on 2015-05-13 16:20
Unit was installed late 1960\'s. Need speakers, knobs and covers to upgrade system.
➡️ Reply
#Reta Electronic by Benny Asif on 2015-08-16 13:33
Dear Sirs,Please be informed that we are in need of data sheet for THYRISTOR-STROMRCHTER made by Reta Electronic. The type number is 531. Drive model is D5200 Siegburg.Would you let us have data sheet for the same in English, please?Thank you and best regardsBenny
➡️ Reply
#Rittenhouse by Jolene Gross on 2015-08-16 14:22
I have a Rittenhouse model c8229 door bell in my home that is not working. I would like to have it repaired.Thank you,Jolene Gross717-781-3692
➡️ Reply
#Rittenhouse by chris on 2015-08-27 21:30
I have gone through the trouble shooting I have 16 volts to the main unit just nothing coming out of main unit. like its acting as if there is no voltage. will not power up, no intercom, no radio is it replacement time or can this be repaired relatively cheap?
➡️ Reply
#Rittenhouse by mike boccio on 2015-08-28 16:39
hi I have a m7034 intercome system.The out door speak into box was flooded by our sandy storm.Needs to be replaced.The wiring is good and it would be easy to replace if I had original replacement kit. thank you mike
➡️ Reply
#Rittenhouse by Mark Danko on 2015-09-10 19:17
Hi, need repair to this unit, sound cuts in and out when volume control knob is turned/wiggled. Moving molex 5 pin connector on circuit board also causes power to cut in and out. Mode delector knob has become stiff to operate. Please send estimate if repair is possible, thanks
➡️ Reply
#Rittenhouse by Scott Steffens on 2015-09-15 22:03
I have a Artolier Lighting & Sound Div - Emerson Electric Co / Rittenhouse Operations Honeoye Falls, NY 14473 Model C8577 - 16 Volts. Do not know how to wire. It was working when it was taken from another home.This home is set up with one front door bell - ding dong doorbell on 1st floor and the...
Show More
➡️ Reply
#Rittenhouse by Lynn Young on 2015-09-20 19:01
Did you locate the 3 coils you were looking for ? I also need one
➡️ Reply
#Rytec by David Salata on 2015-09-22 20:41
Model DG1200 Rytec Do you work on these?Can you estimate cost and turn around time?Thanks. You worked on an Atlas Copco controller ....still works !!
➡️ Reply
#Robotool by Klaus on 2015-10-07 20:33
Looking looking for someone that can troubleshoot the control box for the Roto tool we can send PCBoards to them to do bug in the main control since we have no idea what\'s wrong with it it drilled so many holes and goes to one hole again and stops the whole that is already drilled.Are you capable o...
Show More
➡️ Reply
#Rittenhouse by Bil Hoag on 2015-11-11 17:58
Installed in 1987 when we built the house. Has begun sporadic multiple, single dings, all hours, day and night. I have replaced, back up battery and fuse in motor. Now makes a fairly loud buzzing sound also. Thoughts?
➡️ Reply
#Rittenhouse by Angela on 2015-11-22 00:03
i am looking for the cover of the door chime for the above model that needs replacing.
➡️ Reply
#Rittenhouse by martin stacy on 2015-11-30 23:17
Hi, I just moved into house with Artolier Musician M7011 by Rittenhouse which doesn\'t work. I know you don\'t know why it doesn\'t work but any ballpark guesses at repair cost if I ship it to you? My zip is 516539 thx
➡️ Reply
#Rittenhouse by Bradley Lowe on 2015-12-05 21:41
HelloIt came with the house had a ele.and he had no luck with repair
➡️ Reply
#Reta Electronic by Egon Rodrigues on 2016-01-03 19:24
Hello i need the Manual of reta electronic d52 siegburg
➡️ Reply
#Reta Electronic by Egon Rodrigues on 2016-01-03 19:24
Hello i need the Manual of reta electronic d52 siegburg
➡️ Reply
#Rittenhouse by Sylvia on 2016-02-03 03:15
4 out of 10 times whenever I press the button it works.How do I know if the transformer that needs replacement or if the wiring itself that went wrong? I have replaced the button and it should not be the problem itself.How much would it cost if you send someone to fix it?Thanks.
➡️ Reply
#Rittenhouse by mccammond99@att.net on 2016-03-19 17:03
is there anyway i could get another one of these door bells?
➡️ Reply
#Rittenhouse by Paul Gilbert on 2016-06-07 01:02
Need to replace existing bell system with new Paul gilbert
➡️ Reply
#Reta Electronic by Mr ROHAUT on 2016-06-22 06:39
HelloWe need please manual for RETA 531 - 23 in French or English thanks for helpBest regards
➡️ Reply
#Rittenhouse by Hal Hester on 2016-07-09 23:01
Similiar issue, my doorbell kept sticking. So I replaced the sticky button but now my springs inside the bell housing seem to be sprung and unable to move the plunger the full range to ring or retract.
➡️ Reply
#Rittenhouse by Hal Hester on 2016-07-09 23:01
Similiar issue, my doorbell kept sticking. So I replaced the sticky button but now my springs inside the bell housing seem to be sprung and unable to move the plunger the full range to ring or retract.
➡️ Reply
#Rittenhouse by GENE LAYNE on 2016-07-28 12:11
Can you advise if a Emerson Rittenhouse RC 577 Doorbell mechanical chime will work with a 24V Transformer?I have a 16V and wanted to add a camera to this?ThanksGene 732-754-1205I cannot locate a manual im guessing this was made in the 70\'s
➡️ Reply
#Rittenhouse by Kathy on 2016-08-16 17:08
can i have this unit repaired and what do i need to do.
➡️ Reply
#Reliance by kokyaw on 2016-08-28 00:00
Reliance 2gu21007 not powering on, no response to controls. Need immediate assistance. Thank you.
➡️ Reply
#Reta Electronic by hamid reza on 2016-08-31 11:15
hi. i need datasheets or manuale or wiring for reta electronics drive type BV532/45-13-02
➡️ Reply
#Rittenhouse by Paul on 2016-09-11 18:49
Are you able to repair it?
➡️ Reply
#Rittenhouse by Emily Gladden on 2016-10-16 21:20
When you press our door bell button a chime is not coming out of the box in the outlet.
➡️ Reply
#Rittenhouse by Sharon on 2016-11-27 00:16
we have an old rittenhouse intercom system. the units look old but still works fairly well. need information on how to update system. we're remodeling in some areas and would like to check out updating units. don't have specs on the system. not sure of specs but Name on the system ...
Show More
➡️ Reply
#Rittenhouse by phil hartshorn on 2017-01-10 16:24
need wiring diagram for c8538r door chime
➡️ Reply
#Rittenhouse by Tracy BROWNING on 2017-01-13 09:02
I have an old Rittenhouse door chime that is missing it's tubular bells. Home built in 1932. Chime cover has two decorative brass musical notes and a few horizontal brass what look like pinstripes. After researching, I believe it's 30's vintage and original to the home. I ...
Show More
➡️ Reply
#Rittenhouse by Andrew Lazazzera on 2017-01-16 17:16
HAVE --MODEL DS-2 DOOR SENTRY SAYS 'NOT TO CONNECT TO POWER SOURCE OTHER THAN STANDARD 16 VOLT CHIME TRANSFORMER'NEED TESTING OF ITS TRANSFORMER.I THINK ITS THE TRANSFORMER!WHAT IS PROCESS TO FOLLOW FOR THIS?ANDREW h=773-589-0150 c=773-899-0423
➡️ Reply
#Rittenhouse by Don Heeter on 2017-01-17 21:38
Dear Sirs, I have a Model RM-2.It was put in when the house was built in 1966.It does not work.Thank you for your help.
➡️ Reply
#Rittenhouse by ElectraChime on 2017-01-22 03:43
I can make new bells for this chime. See my sites: doorbellmuseum.org and electrachime.comBestRobert
➡️ Reply
#Rittenhouse by John Reaney on 2017-02-11 01:00
Hello, I have a rittenhouse door sentry. #M9035 w/ a M 9305 door station. The indoor station seems to work, it unlocks the door when the button is pushed. The M9305 out side station is my problem, the speaker is fried and the button is missing. Would you have these items? or where I might find them.
➡️ Reply
#Rittenhouse by dan mazzola on 2017-02-17 16:32
need a sequence timer for a emerson rittenhouse model # 632 631
➡️ Reply
#Reta Electronic by Ricardo Vega on 2017-03-22 13:43
Dear sirsWe have need very urgently de electrical diagram of card ,reta-electronic5200 sierburgzbest regardsRicardo
➡️ Reply
#Reta Electronic by Ricardo Vega on 2017-03-22 18:12
Dear SirsWe have a problem whit one old machine.The reta-electronic 5200 siegbur are dammaged.Can you send electronics wiring for emergencia repair.We are very appreciate you help.Best regardsRicardo VegaBuenos AiresArgentina
➡️ Reply
#Rittenhouse by Gregory Luchey on 2017-03-26 21:44
Door Bell repair motor needed
➡️ Reply
#Rittenhouse by LINDA BURGESS on 2017-03-30 17:16
Have model C 8203, 10 volt door bell. Am missing the push button remote that fastens to wall outside the front door. Any suggestions?
➡️ Reply
#Rittenhouse by macgretz on 2017-04-19 20:58
I have a Rittenhouse Emerson Elec Model C8326 (perhaps 1960's) that has stopped working today. The chimes and housing seem okay, but the mechanism and bell button are old and worn out. Do you have replacement parts - and at what cost?
➡️ Reply
#Rittenhouse by Ken Bentham on 2017-04-25 21:05
Bell is connected to two doors. The front door works fine. The rear door won't ring at all. Can't tell what might be disconnected. Any ideas would be a big help. Thanks.Ken Bentham
➡️ Reply
#Rittenhouse by Harry Yagi on 2017-05-11 12:40
Due to the worn-weakened spring on the hitting bar which do not pop out from the solenoid hole. Do you sell the spring or the entire solenoid with the hitting bar?
➡️ Reply
#Rittenhouse by Mark Malan on 2017-05-17 14:32
My manual says 4-8 Note Chime Models (534, 535, 552, 577, 618, 633). I don't know which one I have. It has long chime tubes and a clock on top. The door bell works great, but the clock doesn't.
➡️ Reply
#Reta Electronic by kursat on 2017-06-13 08:36
reta electronic 5200 siegburg manual pdf
➡️ Reply
#Rittenhouse by Maria on 2017-06-19 14:33
I need wiring schematic for Emerson door chime model C8578-1
➡️ Reply
#Rittenhouse by Donald Brown on 2017-07-07 23:15
I need to have a bulb replacement performed on a 1980ties vintage bronze doorbell. The spring works fine but light nolonger stays on.Regards, Don
➡️ Reply
#Ratelco by joe coito on 2017-08-18 18:20
thank you I have a ratelco rectifier battiery charger I have no model number nothing I'm looking for a shop manual owners manual what ever is there a way mabe I could send you some pics of this and mabe you can help me out thank you
➡️ Reply
#Rittenhouse by Gord Sweatman on 2017-09-01 21:46
Removed outer casing - now doorbell doesn't work - noticed loose redwire - where do I attach?
➡️ Reply
#Rittenhouse by Mark on 2017-09-04 20:48
I'm looking for a replacement circuit board for a Rittenhouse model C8538. Please let me know where I can purchase one.
➡️ Reply
#Reta Electronic by ION on 2017-09-05 05:04
manual for reta electronic 5200 conection electrical
➡️ Reply
#Rittenhouse by Robin Campbell on 2017-09-10 05:21
I have a Rittenhouse master model 550 and 551 doorbell to be tested and repair if needed.
➡️ Reply
#Rittenhouse by Ray G. Brubaker on 2017-09-11 14:32
I have a model Rittenhouse # E780DC door bell push button. The center plastic button is broken. I need a replacement . I can use the whole assemblyPlease email me as to where I can buy it. Thank you.
➡️ Reply
#Remco by JOHN CALLAHAN on 2017-09-13 00:00
Looking for a technician who can repair a Remco COD.5147 Washer & Dryer Control Board. The unit is unresponsive despite being powered on. Thank you.
➡️ Reply
#Rittenhouse by David Bergeron on 2017-10-23 07:12
wonder if I can acquire 1of the 3 boxes that throws the donger to. ring the far right chime of 3
➡️ Reply
#Rittenhouse by Dave Spieker on 2017-11-06 22:05
I am looking for a Rittenhouse Chime Receiver Model C8931R. Would you have one available for purchase or can you direct me to a person or another company that may have one available. Thank you!
➡️ Reply
#Rittenhouse by sal on 2018-01-16 16:43
Trying to obtain new springs and strikers/drivers
➡️ Reply
#Rittenhouse by Andrew Lazazzera on 2018-02-05 18:04
Have Model DS-2 Door Sentry w/ 16v. chime transformer -Rittenhouse #30 or = need local chicagoland technician to trouble-shoot the control box w/ its transformer.-believe transformer is problem.
➡️ Reply
#Rittenhouse by David on 2018-03-04 18:16
Have you ever heard of a response on the Rittenhouse 631/632. I too am refurbishing one and need to know the correct tranformer voltage needed and a wiring diagram surely would help. Any insight?
➡️ Reply
#Rittenhouse by william j paveletz on 2018-03-09 19:10
i need a part model c8633 volts 16 need the main eletric gear
➡️ Reply
#Rittenhouse by Tobie Ross on 2018-04-13 02:54
I have a Sears Solid State Am-FM Master Station Radio/Intercom Model 113.35150 built by Emerson Electric. Can you repair this station. Please advise/
➡️ Reply
#Rittenhouse by Irene Shefts on 2018-04-25 21:04
Model# S7808. The detector has been making loud clicks, usually two at a time. What does this mean? Replace it or cleaning. Please help very annoying.
➡️ Reply
#Rittenhouse by Dale Adams on 2018-05-15 14:40
I need my rcm 4 repaired or replaced
➡️ Reply
#Rittenhouse by Charles Sumrell on 2018-06-16 18:05
Tag on door chime unit says:Model 8846RVolt 16Rittenhouse Division Spartan ElectricFayetteville NC 28386The unit has four tubes, it has a circuit board with integrated circuits. The transformer is putting out 18.5 volts, although the unit says 16 volts on transformer and circuit board. I assume the ...
Show More
➡️ Reply
#Rittenhouse by Charles Cheshire on 2018-07-13 22:04
Cannot reset time seems stripped.Only two of the chimes work.Where are you physically located.ROUGH repair cost.
➡️ Reply
#Rittenhouse by Kathy Grant on 2018-09-24 16:43
I recently purchased an older home that has a Model # RC-475 - 16 volt door chime that works fine, but lacks the cover. Is it possible to purchase just a cover from you or is something like this no longer available. Amazon has one but the mfg. dimensions wouldn't fit. As close as I can meas...
Show More
➡️ Reply
#Rittenhouse by Paul Winchock on 2018-10-15 21:41
I have a Rittenhouse 550, 551 doorbell chime.The unit itself works fine. What I am missing (which someone was supposed to nor trash) is the transformer that sequences the chimes. Do you have a transformer for this that will work? And if so, obviously, what would one cost?Thank you for taking the tim...
Show More
➡️ Reply
#Rittenhouse by Bob Przybylski on 2018-11-28 01:06
I have a Rittenhouse door bell model c8355 and the transformer (that is what I think it is) has failed & does nothing but hum. Can I get a new transformer? or can I buy a replacement at the local home depot or Lowes?
➡️ Reply
#Rittenhouse by Raymond V Normand on 2018-11-29 17:19
Can you sell me Grommets for my Ritten house Model 236 soundbars?
➡️ Reply
#Rittenhouse by Dick on 2018-12-06 23:40
Part #C80Q0 door bell switch.Can I order a replacement ?
➡️ Reply
#Rittenhouse by Craig on 2018-12-27 00:39
I have a 620R, but your post was a long time ago. Did you get an answer?
➡️ Reply
#Rittenhouse by ellen wright on 2019-03-18 14:12
who repairs or work on the old Rittenhouse intercom systems.I would like to do an upgrade. Since I already have holes in the wall from the old Rittenhouse. I would like to upgrade to something along this same size.
➡️ Reply
#Rittenhouse by Tom Bell on 2019-04-10 01:02
I have a Rittenhouse 631/632 doorbell that works ok but the clock motor is noisy. Can I buy a replacement motor for it?
➡️ Reply
#Rittenhouse by Diane P on 2019-05-22 14:20
I have a rittenhouse westminister door chime master model 631 and 632 that I removed from my family home when it was being sold. I have everything except the Rittenhouse no. 42 transformer, which is need before the electrician can install it in my home. Do you have this transformer or know where I c...
Show More
➡️ Reply
#Rittenhouse by Galen Beaupre on 2019-06-10 14:27
I have a Rittenhouse Model 526.What would cost to test it?
➡️ Reply
#Rittenhouse by George Pond on 2019-07-27 20:32
Can you repair the solo kids on this 1950s era doorbell?It’s generally ok except that some of the parts that slide in the tubes to ring the chimes are lost. I could send it in or you could sell me the parts to fix it myself. Thanks,George Pond
➡️ Reply
#Rittenhouse by Eddie Rodriguez on 2019-10-13 21:47
I have a Master Model 631 & 632, The clock stop working. its showing the red dot on the face of the clock that indicates power failure. The chimes still work fine with no issue. Can you provide instruction on how to test and/or repair. Thank youEddie
➡️ Reply
#Recognition Systems Inc by Kulpa on 2019-10-22 00:00
Seeking repair for a Recognition Systems Inc. HK-CR hand scanner unit not powering on. Urgently need assistance with diagnosis and repair. Thank you.
➡️ Reply
#Rittenhouse by Warren Williams on 2020-04-18 04:45
4 Chime Doorbell With Clock .I Need Instriution Manual and wiring DiagramArtolier Lighting & Sound Div. Emerson Electric Co. Rittenhouse Operations Honeoye Falls NY 14472 Model C8633
➡️ Reply
#Rittenhouse by Larry Yudkowitz on 2020-05-13 00:16
I have Model 380 16V. I had connected it ot a Ring Video 2 Doorbell and it worked fine for several months. Now there is a loud humm coming from the chime. I think the Ring ihas a problem. Ring says the chime may not be compatible. Ring says the model 382 is compatible. Whould you know the difference...
Show More
➡️ Reply
#Rittenhouse by Dan Mazzola Sr on 2020-05-31 15:36
I’m in need of a sequence timer for the above mentioned Emerson Rittenhouse clock/chimePlease advise on getting 1 of them by email or by calling me at 617/590-3509New or reconditioned
➡️ Reply
#Rittenhouse by Richard Burnham on 2021-03-28 21:10
Front and back door bells. I need a diagram showing how to connect the wires from the doorbells. Front works with one wire from Front doorbell going to Terminal B and the other going to Front in the 16 VAC group. I assumed one wire would go from Back doorbell to Terminal A and the other to Back in t...
Show More
➡️ Reply
#Ram Electronics by Felix Dannhauer on 2021-04-26 00:00
The control module in my Ram Electronics RAM-1MC1-06 is not responding to any input commands. Looking for repair services to diagnose and fix the issue
➡️ Reply
#Rittenhouse by James L Rockney on 2021-10-04 16:06
The small piston that strikes the chime does not return back to the original position. There is a spring on the piston. It seems like the piston should have a retainer of some sort on the end to hold the spring in place. Is there supposed to be a retainer on the end of the piston to keep the spring ...
Show More
➡️ Reply
#Rittenhouse by Jason on 2021-11-27 23:30
I believe it was 16v AC current . not DC at least thats how mine is.
➡️ Reply
#Reliance by Peter Buchanan on 2021-12-15 00:00
Reliance 802261-88r not powering on or responding to commands. Urgently seeking repair service.
➡️ Reply
#Rittenhouse by Bill Corbett on 2022-02-07 13:47
Emerson c8203 replacement transformer?Any help would be appreciated.Thanks, Bill
➡️ Reply
#Rittenhouse by Starla Irvin on 2022-03-20 00:17
Moved in 3 years ago the AM/FM worked but nothing else. Wondering if I could get an estimate
➡️ Reply
#Rittenhouse by radu munteanu on 2022-04-20 17:35
Good day, I would need the wiring diagram for a Rittenhouse Clock Model 631/632. Just saved the clock from our old house before remodel and we want to install it back with a running clock and the chime.Thank youRadu 650-450-4806
➡️ Reply
#Rockwell Automation by GLORIA MBA on 2023-11-20 00:00
Hey there, I've been asked to look into an issue with a Rockwell Automation 6189-1CPU366 14020-050 CPU card, but I'm not very familiar with hardware repair. I was told the unit needs to be fixed or replaced. Can you provide guidance on how to proceed with this? Any help would be greatly appreciated....
Show More
➡️ Reply
#Reliance by Stephanie Toniolli on 2023-12-17 00:00
Having issues with a Reliance 2GU21002 unit - no power or functions working currently. Need assistance ASAP.
➡️ Reply
#Rittenhouse by Marlene Ilijanich on 2024-06-26 02:50
Hello, I purchased my 4 note-8 note melody door chime in 1995. It has been set up on a battery operation operation
➡️ Reply
#Ru Electronics by wayne martin on 2024-08-22 00:00
The RU Electronics PWB-0636-03 power supply board in our industrial unit is not providing any power output. Looking for a repair service to fix the issue
➡️ Reply
#Reta Electronic by Paulo Cyrus G. Abaring on 2025-02-01 10:37
Dear Sir, I need your enormous help my employer acquired a milling machine and using reta BV 522/28-17-2b converter and we dont have a diagram for plan S.1.522-17-1
➡️ Reply

Contact Us

🚑Shop Location🛠️

Industrial Electronic Repair
145 Rockwell Place Ct
Tobaccoville, NC 27050
🚑 Rush repair shipments only — no walk-ins.

📞Phone

1-336-969-0110

📦Mailing Address🚛

Industrial Electronic Repair
931-E S. Main St #204
Kernersville, NC 27284
📦 Mailing Address (for invoices or shipped repairs)
No walk-ins accepted.