Welcome to AGI

We repair a wide range of AGI Equipment.

Ask questions, or 1-336-969-0110 for faster service.

Use the search bar above to find specific manufacturers.

• 40+ years of experience repairing Industrial & Commercial units
• Certified Senior Industrial Electronics Technician
• Ability to do Reverse Engineering
• No job to big or small
• Fast turn around time on most units
• Quality of work comes before profit!
• Old Fashion Customer Service is always the right policy
• Extended warranty
• Free Estimates
• Low Prices

No repair summaries available yet for this manufacturer.

Comments for AGI

📝 Rafael Angel said:

AGIE Mondo Start 20 CNC EDM with control AGIE FUTURA V EC4 Power Supply and control.Machine and control abandoned in an hazard enviroment for almost 3 years— Purchase or Repair:

➡️ Reply Agie

📝 Eric Szewc said:

Im trying to hunt down schematics for this control so I can diagnose the problem. Do you have any expierience with these controls? I seem to have a power issue. I just picked the machine up, wired it in and when I powered it up the capacitor/resistor filter on a contactor smoked. I removed them from the circuit and the machine powered up and everything was operational except machining voltage. after a few days of tracing the circuitry a resistor fried on the power distribution card. I have no books for this so Im just flying blind.Eric— Purchase or Repair:

➡️ Reply Agie

📝 Jimmy Gray said:

LOOKING FOR SOFTWARECOPY OF HARD DRIVE FOR MONDO 20 AND MONDO STAR 50CAN ANYONE HELP?— Purchase or Repair:

➡️ Reply Agie

📝 Dave Archer said:

We have a Pendant control that need repaied for our Agie-Elox Mondo 2. Can you help?— Purchase or Repair:

➡️ Reply Agie

📝 sergio guerrero said:

I would like to request a quote for the following repair services if available:Agilent Infiniium 54820A Defect: CH 2 will not change resolution from 200mV to 250mV signal still small and readings are not accurateT-BERD 211 Defect: no communicacion RS232 with PC— Purchase or Repair:

➡️ Reply Agilent

📝 Thanh Nguyen said:

I need to repair an Agie hand box. Please contact me as above info.Best regards,— Purchase or Repair:

➡️ Reply Agie

📝 Thanh Nguyen said:

I need to repair an Agie hand box. Please contact me as above info.Best regards,— Purchase or Repair:

➡️ Reply Agie

📝 Huan Le said:

Agie Sprint wire EDM wen t down, alarm #739 Generator is defective. Can you help ?— Purchase or Repair:

➡️ Reply Agie

📝 Brian Connor said:

Do you trouble shoot and repair older Agie machines ie AC50?— Purchase or Repair:

➡️ Reply Agie

📝 MALCOLM MACDOUGALL said:

our keyboard fell apart when it was removed for servicing our Agie Sprint. Apparently the glue that was holding the membrane to the board dried out due to the age of the machine and now it will not make contact with the keys. Since the machine is no longer supported by GF Agie I need to find either a replacement or someone like your company that can repair this keyboard. please contact me at my email address if you can do this, I would be willing to send this for an estimate. i can also provide pictures of the keyboard if that would help. Please let me know if you can repair this keyboard. Thank You, Malcolm MacDougall.— Purchase or Repair:

➡️ Reply Agie

📝 Ron McCracken said:

I am looking for wiring diagram for an Agie Spirnt 20. Is this something you can help me with?Thanks Ron— Purchase or Repair:

➡️ Reply Agie

📝 ibrahim Mohammed Faraj said:

quick update about the Agie 638.864.9 unit - the HPS-03 High Power Supply Board malfunctioned during the night shift. Needs attention ASAP in the morning. Thank you!— Purchase or Repair:

➡️ Reply Agie

📝 Allan Littman said:

The Agie 613.960.4 PMO-05 Power Board unit is exhibiting erratic behavior in the warehouse.— Purchase or Repair:

➡️ Reply Agie

📝 David Woods said:

Hello We have a Agie sinker that has beenj acting up for awhile and here recently we are not able to use the machine. We have had problems with referencing the machine where the y axis goes the the zero then starts to go in the wrong direction to reference. Now it will go down to burn and will stop then drop down a couple 100 thousands of an inch after shutting off. I also am having problems with fine detail on an electrode eroding detail off the part. Do you do service on the field and what would be the cost to look at the machine and give an estimate at repair cost. Thank You David— Purchase or Repair:

➡️ Reply Agie

📝 Christopher Clifton said:

Hello my name is Shayne Clifton. We have an older Agie Mondo 50. For some reason after it starts sometimes it will just freeze. Its happening very frequently. I cant move the machine or anything. I need a tech out this way and didnt know if you service our area and could give us a quote. Regards.Shayne C.— Purchase or Repair:

➡️ Reply Agie