Welcome to CAL

We repair a wide range of CAL Equipment.

Ask questions, or 1-336-969-0110 for faster service.

Use the search bar above to find specific manufacturers.

• 40+ years of experience repairing Industrial & Commercial units
• Certified Senior Industrial Electronics Technician
• Ability to do Reverse Engineering
• No job to big or small
• Fast turn around time on most units
• Quality of work comes before profit!
• Old Fashion Customer Service is always the right policy
• Extended warranty
• Fair Estimates
• Low Prices

🛠️ Common AI Repair Summaries 🏭

Comments for CAL

📝 Peter E. Marcus said:

I would like to have some information on how to use the unit I have. It has the following number on the front just underneath the logo Calterm electronics...66430

➡️ Reply Calterm Electronics

📝 Peter E. Marcus said:

Do you folks have a manual for the use of your ohm meter? If so I would like to obtain one. Thank you

➡️ Reply Calterm Electronics

📝 Cathe Lewis said:

Hello, my boyfriend has this unit and needs to get hold of some kind of owners manual. Can you help??????

➡️ Reply Calterm Electronics

📝 Floyd said:

HAVE LOST THE SCREW THAT HOLDS THE BACK OF THE METER ON BUT CANT FIND THE RIGHT THREAD SIZE. WHAT IS THIS THREAD SIZE?

➡️ Reply Calterm Electronics

📝 scott stephenson said:

could you send me a manual for this OHM Meter, Please, Thank You, Scott

➡️ Reply Calterm Electronics

📝 ric houle said:

Hello, iown this unit and need to get hold of some kind of owners manual. Can you help??????

➡️ Reply Calterm Electronics

📝 william Denson said:

I need the operators manual for the 66420 Caltrem meter. I would appreciate being able to download the manual. I am not able to download from fixya

➡️ Reply Calterm Electronics

📝 ben guttridge said:

used this to turn on/off fog lights. lights turn on/off but the switch does not illuminate. tried three different switches. what am i doing wrong?wired both light together-grounded to fender and ran hot to accessary center post on switch. ran wire from top post to battery and ran ground wire from bottom post to under dash

➡️ Reply Calterm Electronics

📝 Doug Womack said:

I expieienced the same thing on the switch I just bought except the lighted switch came on and no lights. Then I rewired it with a jumper between the ACC & Power terminals and got Lights when the switch was on and lighted switch when the switch was off. I think the switch is defective but Im no expert. What did you come up with for a fix on yours?

➡️ Reply Calterm Electronics

📝 Albert F Borgman C\'78 said:

1987 Oldsmobile Cutlass Supreme Broughham A picture or sketch of how to install the in dash igniion wiring. How do I get to the wiring?

➡️ Reply Calterm Electronics

📝 Charles Braine said:

HelloI am wondering if you have or know where I can find an owners manual for this meter.Thanks Charles Braine

➡️ Reply Calterm Electronics

📝 Carlos Zaldivar said:

I have a manual for my Calterm Electronics Calterm 66474 Digital Engine Analyzer that I could copy and mail to you. Sorry, I need to keep the original.

➡️ Reply Calterm Electronics

📝 Chris Mandich said:

I have just purchased a 66430 Multimeter and the common lead wire came out of the probe.It appears the solder was not done correctly.Is therre a way to get a replacement lead from the manufacturer?

➡️ Reply Calterm Electronics

📝 Fumeffeme said:

Where to Find toshiba satellite a75-s226 and reviews inspiron 13?

➡️ Reply Calterm Electronics

📝 Utertysidssic said:

It is remarkable, rather valuable answer

➡️ Reply Calterm Electronics

📝 Mosesyassulse said:

Im delighted to claim the fact that Im the newest participant right here and as i i am looking forward to chatting together with every body throughout here soon.

➡️ Reply Calterm Electronics

📝 May said:

Hello!I am with a distributor and my customer is looking for the specs/datasheet for Calterm Electronics 41800.Please email information to mprado@newark.comThank you!MayNewark element14

➡️ Reply Calterm Electronics

📝 christopher said:

Hello,I recently changed the battery in my multimeter (66430), and when I turn the dial to 20V DC to measure a battery, I get a -1 display. This display comes up as I turn the dial and before I have plugged in the tester terminals.Please help,Chris

➡️ Reply Calterm Electronics

📝 Paul Miller said:

I want to purchase various sizes and Quantities of Calterm Polyolefin Shrink Tubing. Please direct me to the proper venue. This stuff is the BEST!Thank You so much..........Paul

➡️ Reply Calterm Electronics

📝 rick cooley said:

I BROKE THE LCD SCREEN ON MYANALYZER AND WAS WONDERING IF YOU WOULD HAVE A REPLACEMENT FOR IT I TOOK IT APART AND AND IT LOOKS LIKE ONLY 4 SCREWS HOLD IT . SO I WAS WONDERING IF YOU SOLD THIS PART AND IF I COULD PUT IT IN MY SELF OR IS IT SOMETHING THAT NEEDS TO BE DONE AT A SHOP ? IVE HAD IT A LONG TIME AND DIDNT WANT TO SPEND A LOT ON IT . IT JUST HAS LOTS OF CENTAMENTAL VALUE TO ME . I WOULD BE GRATFULL FOR ANY HELP YOU COULD GIVE ME ON PRICE OF PART OR HOW I NEED TO GO ABOUT FIXING IT THANK YOU

➡️ Reply Calterm Electronics

📝 Linda Blackmon said:

Hey team, the Calco 8411 controller went down mid-shift. Need someone to check it out ASAP in the morning. Thanks!

➡️ Reply Calco

📝 chris hendricks said:

: Our companys copier has been experiencing consistent issues since late last month. Its failing to scan documents and prints them at half the quality of our previous model. We also have concerns about paper jams which are occurring more frequently, potentially causing delays in our workflow. This machine is no longer meeting our productivity needs and is costing us valuable time. Based on my understanding, a replacement could cost around as we need to ensure functionality before the next quarters deadline.:

➡️ Reply Calco