Welcome to CI

We repair a wide range of CI Equipment.

Ask questions, or 1-336-969-0110 for faster service.

Use the search bar above to find specific manufacturers.

• 40+ years of experience repairing Industrial & Commercial units
• Certified Senior Industrial Electronics Technician
• Ability to do Reverse Engineering
• No job to big or small
• Fast turn around time on most units
• Quality of work comes before profit!
• Old Fashion Customer Service is always the right policy
• Extended warranty
• Fair Estimates
• Low Prices

🛠️ Common AI Repair Summaries 🏭

Comments for CI

📝 gasefela ngakaemang said:

Subject Repair Issue Report - Cincinnati Milacron milc-3-424-1953aDear ,I am the inventory manager at , and I have noticed that the Cincinnati Milacron milc-3-424-1953a unit has been repeatedly returned or reported for repair. The reasons provided on paper or by our technicians are currently unknown to me. Could you please investigate further and provide a detailed assessment of the recurring issue?Thank you for your attention to this matter.Sincerely,Inventory Manager,

➡️ Reply Cincinnati

📝 Jin-Soo, Lee said:

We use Touch view graphic flat panel of Cincinnati dynacomp. Inc.(Item #1007410107 Rev.C, Model # 7000-ST-E256, Lot #40524180, Serial #6508610021)We want to buy new graphic flat panel set.Would you like to send me the contact point of yours or cincinnati dynacomps. (E-mail or Fax. No. - I want to contact through e-mail only)

➡️ Reply Cincinnati Dynacomp

📝 HALCOM INT. said:

HELO,WE HAVE A CNC CINCINATI MILACRON MAXIM 500 MACHINE WITH ACROMATIC 950 CONTROLWE ARE LOCKING FOR CPU 3-533-0346G USED,AND OUR QUESTION IS IF WE CAN FIND IT IS POSIBLE CHANGE THE CPU FOR 3-424-2026ATHANKSHalcom International

➡️ Reply Cincinnati Milacron

📝 cindy dase said:

machine is arrow 1000. starts up until and says keypad touch screen missing. any suggestions?

➡️ Reply Cincinnati Milacron

📝 Ed said:

Cindy Dase wrote machine is arrow 1000. starts up until and says keypad touch screen missing. any suggestions?Cindy,Have you been able to locate the problemEd

➡️ Reply Cincinnati Milacron

📝 suyatno said:

Problem or Bad IO CHMD + CMHD AND AXISSERVO DV5

➡️ Reply Cincinnati Milacron

📝 douglas yeh said:

Dear Sir5:We have a Cincinati CNC machine using Acromatic 2100 control system.The machine has started to boot under DOS, then Windows NT4.0 has been loaded. It then load Vicker software and the monitor color changed to pink stripe. We can see nothing but the pink striped monitor thereafter. I am not sure this is touch screen monitor problem or video card problem. Could you please let me know your opinion and thought. Thanks!Douglasdyeh@pantronix.com

➡️ Reply Cincinnati Milacron

📝 Venugopal Miskin said:

Dear Sir,We have cincinatti milacron cnc turning centre on our machine monitor is indicating that X axis HDRW Diagnotics fail Alert code is 00453. Pls send our reply for the sameRegards,Ind-Tech Engineering,Ph 001-0836-4265858, 019880261326HUBLI-580 030 (Karnataka State) INDIA

➡️ Reply Cincinnati Milacron

📝 Tom Fellberg said:

Hello;We have a number of Cincinnati Milacron Camac lcd screens that are in need of repair.These screens are on injection molding machines of late 80s vintage. The Camac was the latest control at the time. The screens are yellow lettering on a black backround. Currently we are able to read only parts of the text. We have had no luck through CM and have had little success with local repairs.Can you help us?Tom FellbergMaintenance ManagerCommercial Plastics Co.Mundelein IL.847-566-1700 EX 234tomf@ecommercialplastics.com

➡️ Reply Cincinnati Milacron

📝 Chinthaka Balasuriya said:

We are the largest tyre and rim manufacture and exporter in sri Lanka. We use many machines in our production line.We have CINCINNATI MILACRON – SABER 500 CNC vertical machining centre. But unfortunately it have a problem.Z Axis moving Down During Power cut upto 5mm. Z Axis have the Break Motor & No counter Balance. We changed the New Break also. Problem not solved.The Drive is CINCINNATI MILACRON BDS4.Please help me for solve this problem.I have sent here with the all data of the motor. Please check the details of motor . Goldline brushless P.M ServomotorModel 1-604-0222Serial No 96E 414W-564Can I change the X axis servo drive and Z axis Drive for check the drive?. If possible what are the settings of drives.

➡️ Reply Cincinnati Milacron

📝 shane brumbaugh said:

I am trying to find the operators and set-up manual for a vickers bds4210-23414w32. any help would be great.Thanks

➡️ Reply Cincinnati Milacron

📝 Terry L. Crow said:

We have a bunch of Cincinnati Milacron electronics we striped out of a Sabre, 2100, 750 and an arrow 500 VMCsLet me know and Ill send you pictures

➡️ Reply Cincinnati Milacron

📝 HEDI said:

Machine is displaying error code 35313564a, causing production downtime.

➡️ Reply Cincinnati

📝 Brian Petit said:

Im presently looking for a wiring diagram for a Cincinnati milacron milling machine. MODEL#-LL, Procuct#-315-16 plain dial type, Serial#-3104PT8-0015, ACVOLT-460, PH-3, HZ-60, Control diagrams-F-314290. Any information you can provide would be greatly appreciated.Thanks,Brian Petit

➡️ Reply Cincinnati Milacron

📝 Miroslav Petkov said:

Im looking for a electrical diagram for a Cincinnati Milacron machine.Best regards,Miroslav Petkov

➡️ Reply Cincinnati Milacron

📝 LUIS SANCHEZ said:

HI!Im looking for a quote on repair of a power supply unitfor a CINCINNATI MILACRON ARROW750If there is something you can help me Illapreciatethanksluis

➡️ Reply Cincinnati Milacron

📝 Indika Uduwila said:

Dear Sir,IN our cnc machine we use cincinnati milacron bds4 drives.But in sudden power cut Z Axis drop few mm down without any alarm. could you please tell us whether this is a fault of axis drve or can we adjust any nob (balance , stability or current limit) to overcome this problem

➡️ Reply Cincinnati

📝 bipin said:

Sir, We bought a used Cincinnati Arrow 2000 machine with TNC 426 Control. We want to start the machine . As we do not have any Electrical manuals and Drive manuals we are stuck at some errors . We need drive BDS4 service manual and Electrical manusl to resolve our problems . pl. help to start our machine . At immediate help pl. let us know What would be the problem as drive shows error of Under Voltage . Please suggest some remedies.Thanks & regards ,Bipin

➡️ Reply Cincinnati

📝 Mark said:

Hello, I have a cincinnati milacron Lathe with a VFS5 275/2604A-10 Spindle drive, do you repair these drives? what would the average cost be to do so. Thanks YouMark

➡️ Reply Cincinnati Milacron

📝 ALEJANDRO said:

HIWe have a VFS5-275-00-2604A VICKERS DRIVER.with the MOTION LINK PLUS SOFTWARE appears a error No 18 BAD TL. but the boars are the same that we used before.We need the password to unblocked the software to reinstall the TL file, that we have. The TL file that we have is VFS5 v 1.03cC with a compensation Board 275/2604a-010.The encrypted key number for the LOCK SMITH COMMAND is 1991923109

➡️ Reply Cincinnati Milacron

📝 Ralph Remington said:

The part number is 840777/I and could you provide a price estimate.

➡️ Reply Cincinnati Milacron

📝 rejil said:

Cincinnati Milacron 3 531 2204a unit not powering on. Need immediate repair assistance.

➡️ Reply Cincinnati Milacron

📝 Jim McNamara said:

Cincinatti-Milacron 35421142A circuit board is not powering on despite usual startup procedures. Need immediate repair assistance to minimize production downtime.

➡️ Reply Cincinattimilacron

📝 schuessler said:

Based on my experience, Ive seen similar issues with the CINCINNATI MILACRON 3-533-0780G GCPU. The common symptoms typically involve erratic system behavior, frequent error messages, and potential communication failures. These could indicate a variety of potential issues, including software glitches, hardware malfunctions, or power supply problems. I recommend further inspection by a qualified technician to pinpoint the exact cause of the problem.

➡️ Reply Cincinnati Milacron