Welcome to Calterm Electronics

unofficial service & repair forum

We repair a wide range of Calterm Electronics Equipment.

Ask questions, or call 1-336-969-0110 for faster service.

Use the search bar above to find specific manufacturers.

• 40+ years of experience repairing Industrial & Commercial units
• Certified Senior Industrial Electronics Technician
• Ability to do Reverse Engineering
• No job to big or small
• Fast turn around time on most units
• Quality of work comes before profit!
• Old Fashion Customer Service is always the right policy
• Extended warranty
• Fair Estimates
• Low Prices

No repair summaries available yet for this manufacturer.

Comments for Calterm Electronics

📝 Peter E. Marcus said:

I would like to have some information on how to use the unit I have. It has the following number on the front just underneath the logo Calterm electronics...66430

➡️ Reply Calterm Electronics

📝 Peter E. Marcus said:

Do you folks have a manual for the use of your ohm meter? If so I would like to obtain one. Thank you

➡️ Reply Calterm Electronics

📝 Cathe Lewis said:

Hello, my boyfriend has this unit and needs to get hold of some kind of owners manual. Can you help??????

➡️ Reply Calterm Electronics

📝 Floyd said:

HAVE LOST THE SCREW THAT HOLDS THE BACK OF THE METER ON BUT CANT FIND THE RIGHT THREAD SIZE. WHAT IS THIS THREAD SIZE?

➡️ Reply Calterm Electronics

📝 scott stephenson said:

could you send me a manual for this OHM Meter, Please, Thank You, Scott

➡️ Reply Calterm Electronics

📝 ric houle said:

Hello, iown this unit and need to get hold of some kind of owners manual. Can you help??????

➡️ Reply Calterm Electronics

📝 william Denson said:

I need the operators manual for the 66420 Caltrem meter. I would appreciate being able to download the manual. I am not able to download from fixya

➡️ Reply Calterm Electronics

📝 ben guttridge said:

used this to turn on/off fog lights. lights turn on/off but the switch does not illuminate. tried three different switches. what am i doing wrong?wired both light together-grounded to fender and ran hot to accessary center post on switch. ran wire from top post to battery and ran ground wire from bottom post to under dash

➡️ Reply Calterm Electronics

📝 Doug Womack said:

I expieienced the same thing on the switch I just bought except the lighted switch came on and no lights. Then I rewired it with a jumper between the ACC & Power terminals and got Lights when the switch was on and lighted switch when the switch was off. I think the switch is defective but Im no expert. What did you come up with for a fix on yours?

➡️ Reply Calterm Electronics

📝 Albert F Borgman C\'78 said:

1987 Oldsmobile Cutlass Supreme Broughham A picture or sketch of how to install the in dash igniion wiring. How do I get to the wiring?

➡️ Reply Calterm Electronics

📝 Charles Braine said:

HelloI am wondering if you have or know where I can find an owners manual for this meter.Thanks Charles Braine

➡️ Reply Calterm Electronics

📝 Carlos Zaldivar said:

I have a manual for my Calterm Electronics Calterm 66474 Digital Engine Analyzer that I could copy and mail to you. Sorry, I need to keep the original.

➡️ Reply Calterm Electronics

📝 Chris Mandich said:

I have just purchased a 66430 Multimeter and the common lead wire came out of the probe.It appears the solder was not done correctly.Is therre a way to get a replacement lead from the manufacturer?

➡️ Reply Calterm Electronics

📝 Fumeffeme said:

Where to Find toshiba satellite a75-s226 and reviews inspiron 13?

➡️ Reply Calterm Electronics

📝 Utertysidssic said:

It is remarkable, rather valuable answer

➡️ Reply Calterm Electronics

📝 Mosesyassulse said:

Im delighted to claim the fact that Im the newest participant right here and as i i am looking forward to chatting together with every body throughout here soon.

➡️ Reply Calterm Electronics

📝 May said:

Hello!I am with a distributor and my customer is looking for the specs/datasheet for Calterm Electronics 41800.Please email information to mprado@newark.comThank you!MayNewark element14

➡️ Reply Calterm Electronics

📝 christopher said:

Hello,I recently changed the battery in my multimeter (66430), and when I turn the dial to 20V DC to measure a battery, I get a -1 display. This display comes up as I turn the dial and before I have plugged in the tester terminals.Please help,Chris

➡️ Reply Calterm Electronics

📝 Paul Miller said:

I want to purchase various sizes and Quantities of Calterm Polyolefin Shrink Tubing. Please direct me to the proper venue. This stuff is the BEST!Thank You so much..........Paul

➡️ Reply Calterm Electronics

📝 rick cooley said:

I BROKE THE LCD SCREEN ON MYANALYZER AND WAS WONDERING IF YOU WOULD HAVE A REPLACEMENT FOR IT I TOOK IT APART AND AND IT LOOKS LIKE ONLY 4 SCREWS HOLD IT . SO I WAS WONDERING IF YOU SOLD THIS PART AND IF I COULD PUT IT IN MY SELF OR IS IT SOMETHING THAT NEEDS TO BE DONE AT A SHOP ? IVE HAD IT A LONG TIME AND DIDNT WANT TO SPEND A LOT ON IT . IT JUST HAS LOTS OF CENTAMENTAL VALUE TO ME . I WOULD BE GRATFULL FOR ANY HELP YOU COULD GIVE ME ON PRICE OF PART OR HOW I NEED TO GO ABOUT FIXING IT THANK YOU

➡️ Reply Calterm Electronics