Welcome to DI

We repair a wide range of DI Equipment.

Ask questions, or 1-336-969-0110 for faster service.

Use the search bar above to find specific manufacturers.

• 40+ years of experience repairing Industrial & Commercial units
• Certified Senior Industrial Electronics Technician
• Ability to do Reverse Engineering
• No job to big or small
• Fast turn around time on most units
• Quality of work comes before profit!
• Old Fashion Customer Service is always the right policy
• Extended warranty
• Fair Estimates
• Low Prices

🛠️ Common AI Repair Summaries 🏭

Comments for DI

📝 John Langhirt said:

WE are in need of the 2 fiber gears that are driven by 2 right /left film spindle motors. these gears have approxmaetly 90 teeth 3dia & 3/16 thick. gears are interchangeable

➡️ Reply Dietzgen

📝 Brian Taylor said:

The drive gears on both spindals are dry rotted and falling apart. We have some very old weather data that we need to retrieve from microfiche and need to repair the viewer. Where can I get the parts?

➡️ Reply Dietzgen

📝 Bob Day said:

Dear Sir,We have acquired a 1989 McNeil Akron Rotocast machine with a Texas Instruments computer using an 8 Displaytek monitor (Model # 2003 399 Serial # 90583383 & Toshiba tube E2728B31)Power supply unit appears OK but monitor does not work.Is it possible to replace this unit? If so at what cost. Alternatively is the a circuit drawing available?ThanksBob Day

➡️ Reply Displaytek

📝 luis redman said:

Hey there! Based on my past experience, the symptoms described for the Ditech dt-0t88-554 could indicate a possible malfunction in the power supply or the main board. I would recommend checking for any unusual sounds, flashing lights, or a complete lack of responsiveness from the unit. Feel free to reach out if you need further assistance!

➡️ Reply Ditech

📝 Carol Lervig said:

Looking for Displaytek Corp in Carrollton, Texas. Do they still have an office here? If so, how do I contact them?

➡️ Reply Displaytek

📝 Nicholas M. Trikouros said:

The Calterm Electronics multi meter Model #66464 (Serial#66464 50691294074895) was made by Digital Instruments. I need to obtain a manual for this unit and any help you can give me in obtaining one will be greatly appreciated.RegardsNicholas Trikouros

➡️ Reply Digital Instruments

📝 trevor said:

i got the metr case and manual.... i could make a copy of the maunual if u need it .. relpy back thanks

➡️ Reply Digital Instruments

📝 Jack said:

Especially if its for or near the 66420 model.Thanks in advance, you can email PDFS or Jpegs to rmp2011 AT me DOT com.

➡️ Reply Digital Instruments

📝 chris singer said:

I need to get a manual for this multimeter 66464

➡️ Reply Digital Instruments

📝 pasha said:

Machine Issue Digiplan pk130m is not powering on despite multiple attempts.

➡️ Reply Digiplan

📝 Asif said:

: We are experiencing issues with our manufacture part description units. The units are typically used for , however, . Weve noticed that and it is causing significant downtime. It appears that the has failed, preventing the unit from functioning properly. We estimate that replacing this part would cost around $. Please advise on whether you offer repair services for these units. If so, what are your turnaround times and estimated service fees? Wed appreciate it if we could schedule a consultation to discuss this further and learn about the best course of action.:

➡️ Reply Dip Inc

📝 vikas said:

sir i have req of nsk drive esa-y2020tf1-11 please give me new drive qutation and conation digaram

➡️ Reply Dixson Inc

📝 Derek Mallon said:

Can we run two tachometers of the one signal from the magnetic pickup. I was thinking if we ran the pickup single in a series loop between the two tachometers it may work.Your thoughts please.Kind regardsDerek MallonElectricianOcean AmericaDiamond Offshore Drilling Inc

➡️ Reply Dixson Inc

📝 mitch said:

It seems that your Dinex T2-DIO-888-K7 controller is experiencing issues. Please provide more detailed information on what specific functionalities are not working properly. For instance, does the unit fail to power on, display error messages, or operate erratically? Additionally, if you have tested the controller with different power sources or connections and the issue persists, it may indicate a internal component failure. Based on similar repair cases for Dinex controllers, the estimated replacement cost can range from $100 to $300, depending on the severity of the issue and required repairs. To assess the exact repair cost and turnaround time, I recommend reaching out to Dinex customer support or an authorized service center for a thorough evaluation of your unit.

➡️ Reply Dinex

📝 krishan saini said:

Hello, Ive been informed that the Disa 2040c-1932 unit is currently not functioning. Please check and diagnose the issue accordingly. Thank you.

➡️ Reply Disa

📝 HO-WOONG LEE said:

Hello, I am reaching out regarding a DIECK ELEKTRONIK QPS20-72 VENDING MACH CARD READER CONT MOD that has stopped functioning. We need repair information or a replacement part urgently. Can you please provide guidance on troubleshooting or sourcing a replacement part? Thank you.

➡️ Reply Dieck Elektronik