Welcome to Dyna

We repair a wide range of Dyna Equipment.

Ask questions, or 1-336-969-0110 for faster service.

Use the search bar above to find specific manufacturers.

• 40+ years of experience repairing Industrial & Commercial units
• Certified Senior Industrial Electronics Technician
• Ability to do Reverse Engineering
• No job to big or small
• Fast turn around time on most units
• Quality of work comes before profit!
• Old Fashion Customer Service is always the right policy
• Extended warranty
• Fair Estimates
• Low Prices

No repair summaries available yet for this manufacturer.

Comments for Dyna

📝 Dwayne Lange - Sunspot Solar said:

I am a solar power supplier / installer located in Adelaide, Australia.I have had a client bring in a Bravo QBC 1012 inverter / charger manufactured by Dynamote Corporation.My local inverter repairer is unable to find any specs on these products, but has been able to confirm that the Mosfets are o.k and the fault is in the micro control board.Are you able to provide some product info and / or parts and / or product repair.

➡️ Reply Dynamote

📝 Bill said:

can you tell me the correct fuses for my power invertermodel# A20-50D

➡️ Reply Dynamote

📝 Lloyd Morris said:

A customer brought me a Dynamote President B10-KKK Inverter It trips the reset as soon as you connect 12 volt power to it . I suspect the diodes are fried but have no schematic or anything to help. can you be of assistance?

➡️ Reply Dynamote

📝 DENNIS BERNARD said:

i have a dynomote m a60-120 sn-810189 12 dc system i need to know how to wire my delco remy alternator into it.the alternator model is 111740 s/n 801122 type 150 amps 145.please help. this is for a fire truck and is out of service.thanx

➡️ Reply Dynamote

📝 James Beaman said:

Any and info including schematics if that is possible. We would like to use in the field. Thanks, James

➡️ Reply Dynamote

📝 David Wardle said:

Do you service Dynamote Static Inverters or possibly have a schematic for this unit: Dynamote Brutus TB32-24. Described as : 3200 watt, 24 volt battery powered inverter, hybird hi-low frequency.......high frequency H bridge feeding 60 Hz. transformerThanks, David

➡️ Reply Dynamote

📝 Tina Gilbert said:

Wiring instructions needed for remote. Can you assist me?

➡️ Reply Dynamote

📝 AHMED said:

the wiring diagram and asking about the out put Ac 220 sine wave and asking of the sine wave does it was pure sine wave or not ?

➡️ Reply Dynamote

📝 James Wooldridge said:

Trying to wire the remote switch inverters not working without it

➡️ Reply Dynamote

📝 Barry Coker said:

I am looking for a diagram to hook up a Dynamote Model#A40-120Serl.#811734. This unit is on a 1981 Mack fire truck The trucks eng.was just rebuilt and the inverter didnot work when the truck was picked up. I have no diagrams to Know if I have power at all points needed onthe D C side. Your help would be greatley apreciated Yours Truly.

➡️ Reply Dynamote

📝 James R Pacenti said:

The electrical system was modified by dynamote, sticker said to contact dynamote before makeing any repairs. need to know where the voltage regulator has been located. the vehicle is a 1989 bucket truck.

➡️ Reply Dynamote

📝 richard said:

A friend of mine aquired an inverter that can be installed to a vehicle. when it was found in a box in an old barn,the box and the instructions inside, have deteriorated. Is there anyway to find the manuel.

➡️ Reply Dynamote

📝 Ajendra Prasad said:

Hi , I have a Dynamote power inverto model # B10KKK-TINPUT 14.2 VDCOUTPUT 120VAC10AMPS 60HZMy invertor doesnt come on at all, I have done some test on power supply from battery to circuit breaker and have got 14v there but after the tranformer there is no out put , this unit has a remote connection and do I have to have the remote ? I bought this unit in a auction and has no remote.Is there any possiblty to get a spec or circuit daigram for thsi unit ?thank you very much for your timeAJ

➡️ Reply Dynamote

📝 RYAN WILSON said:

HAVING A PROBLEM WITH POWER GOING IN, BUT NO POWER COMING OUT. POSSIBLY SOLENOID? MODEL # A40-120A/150

➡️ Reply Dynamote

📝 Ty Cummins said:

need to see if you would have a wiring diagram for installation for a dynamote inverter model number a30 70b any help would be great. thanks for your time. Ty

➡️ Reply Dynamote

📝 eric said:

I bought it used ,it works but I would like to know what output wattage it has.I tried to run 2 - 500 watt lights and it would not do it,then I ran a 75 watt bulb on a full charged 1000amp batt.,It ran 37min then tripped low voltage.I recharged the battery, hooked it it to an APC battery backup (1000) amp battery,not stock battery,and it is only raited at 350 amp,it has ben running for 2.5 hour.Why does yours use so much power?

➡️ Reply Dynamote

📝 Julia Lunstra said:

My husband recently passed away and while cleaning the garage I came across this item. It is a Dynamote B20-12 with CD, LVCO. What is it? What is it good for? How much is it worth for me to sell?Any help that you could provide would be extremely appreciated.julia

➡️ Reply Dynamote

📝 Ed Cook said:

I purchase a 1980 Amblance E-350 Ford It has a Power Gaurd Mod. G-B10-10 Ser# 79213 it is on top of Dynamote 1.0 KVAMod. # B10-KKK Ser.# 800226 It is not connected any more to the truck can you send my the instruction manual of it use and connection instruction. If you can help me I baught it for my plumbing Co. Thank you Edward L. Cook

➡️ Reply Dynamote

📝 Mike M said:

Are you familiar with the 15volt biased power supply on the servo side going bad on a Dynapath10? I have been told this is the problem with my mill. The 15volt biased power supply was replaced with a used one that burned up soon after the mill was in operation. Do you have any clue why this would happen? Were wondering if anyone has experienced this before?

➡️ Reply Dynapath

📝 Bill Bailey said:

We are using about 18 of the Dynapro 1031 touch screen moniters in our plant. Wanted to find out if you have the ability to repair these?

➡️ Reply Dynapro

📝 James Smith said:

Monitor boots up to home screen, however home screen has missing buttons on touchscreen and two white square flashing. Monitor locks up!Seems like EEPRom problem?

➡️ Reply Dynapro

📝 Ajendra Prasad said:

Hi , I have a Dynamote power inverto model # B10KKK-TINPUT 14.2 VDCOUTPUT 120VAC10AMPS 60HZMy invertor doesnt come on at all, I have done some test on power supply from battery to circuit breaker and have got 14v there but after the tranformer there is no out put , this unit has a remote connection and do I have to have the remote ? I bought this unit in a auction and has no remote.Is there any possiblty to get a spec or circuit daigram for thsi unit ?thank you very much for your timeAJ

➡️ Reply Dynamote

📝 Ray Mills said:

Hi AJ: There is a female 6 connector plug You need to momentery short out two of the wires. If you want to give me a call I will give you more information. 904-733-9242 or email me.

➡️ Reply Dynamote

📝 Joel Moorman - Moorman Electric said:

Is it possible to obtain a service manual for a Dynamote A30-70D option LD/GF120? Only 40V output and stop button does not shut unit off. Also need a green connector sleeve. If you could help us out, it would be greatly appreciated. Looking forward to hearing from you. Thank You, Joel Moorman Moorman Electric

➡️ Reply Dynamote

📝 Harry Trottier said:

Is it possible to get a manual for a Dynamote A/L25-120 Inverter?

➡️ Reply Dynamote

📝 Mitchell Vavra said:

I bought a used Derrick Digger body, and it has a A60-120D with options/LD/GFI120. The wires were cut off the old chassis and I am currious on how to correctly connect them to my Chassis. Any help would be appriciated.Thanks,Mitch Vavra

➡️ Reply Dynamote

📝 carl shalley said:

my dyna 44 m after initializing sporadically refuses to move in any axis sometimes it will move limit to limit in one axis and then not go in any axis would it be possible to get a little tech advice and if not able to solve problem over phone or by e-mail research cost for field repair???

➡️ Reply Dyna Mechtronics

📝 steve bosco said:

I have this inverter but no manual to install it. can you help me find the paperwork to properly connect this unit? the wires are cut but I have know idea how to connect it to my vehicle.

➡️ Reply Dynamote

📝 MackMillions said:

Urgent Request for Repair/Replacement Info for Dynapro Technologies Inc 1021 Screen MonitorHi , Our Dynapro Technologies Inc 1021 Screen Monitor has malfunctioned. We need repair or replacement information urgently. Could you assist us with this issue ASAP? Thank you,

➡️ Reply Dynapro Technologies Inc

📝 RUSSELL LEYRA said:

GOOD MORNING, I AM LOOKING FOR SOME PRICING ON A REPAIR OR REPLACEMENT FOR A CUSTOMERS DYNAMOTE A40-120D/240.I AM NOT SURE WHAT IS WRONG WITH THE UNIT OTHER THAN IT DOES NOT WORK. THANK-YOU FOR YOUR TIME RUSS

➡️ Reply Dynamote

📝 Dan Harding said:

Can I get a manual and wiring diagram for this unit? Our fire dept. just bought a used rescue truck with a unit on it.

➡️ Reply Dynamote

📝 Jimmie Morgan said:

In a fire truck we bought Puts out about 40 volt Ac Mfg 1995 Want to know if fixable. Thanks Jim Goodman Area Fire Protection District

➡️ Reply Dynamote

📝 Akbar Sabaghi said:

Hello my dear we have an electronic board of a sewing machine show eror 103 then our technecina couldnt solve this eror we need to know which parts on the board is damage as in the machine catalog info is not enoughBest regards!Akbar Sabaghi

➡️ Reply Dynapar Encoder

📝 leon ferrell said:

encdoer plug wiring fan out for plug or manual

➡️ Reply Dynasonics Inc