Welcome to EL

We repair a wide range of EL Equipment.

Ask questions, or 1-336-969-0110 for faster service.

Use the search bar above to find specific manufacturers.

• 40+ years of experience repairing Industrial & Commercial units
• Certified Senior Industrial Electronics Technician
• Ability to do Reverse Engineering
• No job to big or small
• Fast turn around time on most units
• Quality of work comes before profit!
• Old Fashion Customer Service is always the right policy
• Extended warranty
• Fair Estimates
• Low Prices

🛠️ Common AI Repair Summaries 🏭

Comments for EL

📝 Michael Hendrick said:

Hell I was left a EDN ELOX HRP 64 and I would like to get some info on this machine. I dont even know if it works. If there is somewhere I could uptain or even better down load a manual I would be so much in your dept. Thanks Michael Hendrick

➡️ Reply Elox Corporation

📝 Don K said:

We also own a Elox HRP-64 machine. We also are missing the manual and would like to know it you found one and would like to sell us a copy or tell us where you got it so maybe we could also purchase one.Thanks Don Ketz

➡️ Reply Elox Corporation

📝 Rodrigo Avendaño said:

My friend , I could not write before, so that they robbed my to me notebock and it did not find your e mail I feel it. I have been needing to know how you can help me for many months that I cannot make take my machine, here in Chile are technicians no to be able to repair to my machine ELOX heritage fanuc 11. in the monotor the following thing is written: SV013 X IMPROPER V_READY OFF SV013 Y IMPROPER V_READY OFF SV013 Z IMPROPER V_READY OFF EX 002 SERVO MOTOR OVERTEMP BREAKE ENGAGED I believe that your you are the suitable person to solve my problem, do you need antecedents .help my plese. thank you Rodrigo Avendano CONCEPCION CHILE South America prau@prau.cl , is a great surprise your answer I am in favor glad of this, please ayudame with this maquina, the characteristics of the maquina are the following ones: ELOX Heritage 12-3816 004891 CNC # 004891 Processor: 11 FANUC Error Lock: WRITE LOCK TM 020 Z-AXIZ BRAKE ENGAGED X EXCESS DRIFT COMPENSATION And HND STOPLSK Friend to send some picture with the errors. Thank you very much by your aid. Your friend of Chile. Rodrigo Avendano PRAU e.i.r.l. Concepcion CHILE

➡️ Reply Elox Corporation

📝 jayesh vasani said:

We have purchased second hand makino hmc - GE FANUC 15M CONTROLduring starting we found - SV013 Y IMPROPER V_READY OFFSV013 Z IMPROPER V_READY OFFSV013 B IMPROPER V_READY OFFFOR X AXIS THERE IS NO MESSAGEWhat can be the problem ?Pleasge guide usRegards,JayeshIndia

➡️ Reply Elox Corporation

📝 P.M.C.J.Peters said:

To the manual: is it related to the machine?What is de problem that you have?

➡️ Reply Elox Corporation

📝 edwin dulce aguilar said:

quiero el esquema electrico de este modelo

➡️ Reply Elox Corporation

📝 SERGIO AYLLON TREJO said:

disculpen pero no ablo ingles solo spanol me urge el diagrama de una erocionadora elox t50s urge

➡️ Reply Elox Corporation

📝 angel laclaustra said:

HelloI have a 1990 edm fantastic elox cnc with a Fanuc contoller. Eloxtype 3-2012 cncSeerial: 004300ControlType: sys 11 cef 100serial: 89-1573Im having the following erros:EX002 Servo motor over TempOT008 z - over travel (hard)Also i have a cable disconected that i dont know where goes. The cable number is MC-3. Please if can help me i will appreciate. Thanks

➡️ Reply Elox Corporation

📝 Rodrigo Avendano said:

Dear friend. I need aid to ignite 12 EDM ELOX HERITAGE FANUC 11This blocked and I cannot operate it single the board and screen. it throws the following errors to me: TM 020 Z-AXIZ BRAKE ENGAGED X EXCESS DRIFT COMPENSATION And HND STOPLSK EXCESS DRIFT COMPENSATION to know since I make to solve the problem step by step. I am of Chile america South and is very difficult to obtain a solution. or indiquenme algun Web site to solve error. I can send pictures of the screen dame and mail for send Help my please Thanks you Rodrigo Avendano UriaCHILESouth America56-41-282364 prau@tie.cl prau@prau.cl

➡️ Reply Elox Corporation

📝 michael spacco said:

ram will not go up switches work. we had to move it and since then the ram dropped and will not go up. Is it the hydrolics and how do i bleed the air out.

➡️ Reply Elox Corporation

📝 Tim Higgins said:

having trouble with my edm. message ps servo control communication failure is up and wont reset. how can i correct this?machine is 8-2012 cnc sn. 004712 with controll svs11cef58 sn. ps1372 could this be a loose cable/connection, or something more serious.

➡️ Reply Elox Corporation

📝 LEN JOHNSON said:

RAM CYCLIER CANCELS BURN WHEN STARTED. REPLACED PUSH BUTTON BUT IT DOES STILL CANCELS BURN.

➡️ Reply Elox Corporation

📝 Adang Rosadi said:

We have a trouble with our Elox Mondo star 50 EDM machine. Error ocur during axis movement, (E48) A short circuit was detected while jogging or positioning. Would you like to advise us to slove the problem ?Thanks and best regards,Adang

➡️ Reply Elox Corporation

📝 DAVE PURDY said:

HELLO,DO YOU OFFER PARTS FOR ELM SYSTEMS DIGITAL READOUT MODEL ACRA 10.THANK YOU

➡️ Reply Elm Systems

📝 Weir Minerals said:

The x and head axis are giving false measurements,have unit unplugged.Quote to repair unit or a manual on .

➡️ Reply Elm Systems

📝 Andrew Etchells said:

I am trying to obtain some infomation on the electrical connections of a ELDUTRONIC U EMOTRON B V U4T-55/440-M/EMC would appreciate any help.

➡️ Reply Eldutronik

📝 Alfredo Preciado said:

Hi Sir,We have a die cut press with an Elemac motor Type 90S B5, 1.5HP, 1700rpm, 8A. It has a circuit board Elemac 030162 with 14 connections. We urgently need one of this boards. Do you have it???Please repply as soon as posible.ThanksAlfredo PreciadoT-Shirts Interamerica, S. A.

➡️ Reply Elemac

📝 SHEILA MADDOX said:

Do you have a flat rate repair 1 pc 300MTH Elemac light curtaincost of new, deliveryOr please issue RA to send in for repair/evaluation.thanks

➡️ Reply Elemac

📝 Martin Lim said:

Elliptical EP-42 issue Control panel malfunctioning, buttons unresponsive. Need technician ASAP.

➡️ Reply Elliptical

📝 Dale Deremer said:

Hello, I have an old ELVO 1200 cutter. Do you repair these?Thanks,Dale Deremer

➡️ Reply Elvo

📝 Ujuan said:

Our Refinery in Dumai (Indonesia) have Elremco D 78 Type GL 89 Out put per rev 10 min 85 psi to control Air Dryer sistem. Untill now has broken. So we want to replace it.But we have problem to contact your agent in Indonesia. Would you to inform us about this and if the sistem obselete could you suggest the subtitute the sistem.Thanks for your cooperation.Ujuan M

➡️ Reply Elremco

📝 AHMED HASSAN said:

I WANT SPARE PART CAM SPEED TYPED63/4 FOR MOTOR CONTROL

➡️ Reply Elremco

📝 MR VINCENT CHUNG said:

DEAR SIR, PLEASE QUOTE THE FOLLOWING ITEM WITH YOUR BEST PRICE AND DELIVERY PERIOD :-ELREMCO (SMALL MOTOR)TYPE D78RPM 375 240V 50HZQTY : 1 UNITFROMMR VINCENT CHUNGBAE INDUSTRIAL ENGINEERING SDN BHD16-6, PERSIARAN KLEDANG TIMUR 19,BANDAR BARU MENGLEMBU,31450 MENGLEMBU,IPOH, PERAK, MALAYSIA.TEL : 605-2828003FAX : 605-2828005E-MAIL : info@bae.com.my

➡️ Reply Elremco

📝 Rita McCrory said:

Where is South Africa can I get an Elremco Marlow air motor part number 10555623. I am in Gauteng Province / Johannesburg

➡️ Reply Elremco

📝 JOSE MARTINEZ said:

QUIERO REPARAR MI MOTOR NEUMATICO ELREMCO MARLOW PAT. 1055623 VIVO EN MEXICO. GRACIAS

➡️ Reply Elremco

📝 Gary Ittner Industrial Roller Co. said:

I would like to get info, and prices we want to buy one also time table for delivery

➡️ Reply Eltex

📝 Sean Moffatt said:

I have one of these units in a servo roll feed that drives the brushed DC servo motor just fine. The problem is that it does not respond to the +/- 10V control signal. It runs at 100% randomly in fwd or rev when a start signal is applied. The cnc controller was made in the 80s It is no longwer supported (software or electronically), and is basically junk and is going to be replaced with something that is current. I need a estimate for testing and or repairs if possible. Model: AZE-CC4QTipo:AZE LV15/AO-P-110/8,5/24No. Matr.EC 22230Codice:42/88ThanksSean MoffattOperations managerHoffman Mint

➡️ Reply El.Ge

📝 MARKO said:

I NEED COMPLET DC SERVODRIVE EL.GE AZE-CC4Q.PLEASE SEND ME OFFER.

➡️ Reply El.Ge

📝 Ing. Jose Calos Pinto said:

Estimados, tengo que reparar una maquna giben con un controlador AZE-CC4Q, esto es en bolivia, pero no hay informaion aerca de la plaza y su funcionamiento para la secuencia de trabajo, favor ayudarme con este dilema

➡️ Reply El.Ge

📝 Sven Rookie said:

Iv a question regarding the controller:Are there any spare parts for those drives, is there any technical support existing or is there any identical drive which can be used?As USA is quite far away - do you know a technical support in europa?Many thanks for your answer!Kind regardsSven

➡️ Reply El.Ge

📝 mick Sharman said:

There are no spares anywhere. The Poletti & Osta brand is the same, just badged and coloured differently. They are the same as El.ge. identical.You can exchange any higher current rating (average and Peak) as long as it is higher rated, but same Voltage. I could not find any of these, but there was a supplier in UK who had one, but I think it has gone.

➡️ Reply El.Ge

📝 Vlade Vujovic said:

Molim Vas za pomoc,imam cnc morbideli u 15 i ne radi mi DC servodrive Y osa,type AZE-cc4q el.ge,Milano.tipo AZE HV 12/AO-R-200/6,5/18NMATR EC 19613 CODICE 16/88Interesuje me da li imate i kolika je cena?pozdrav i hvala,Vlade

➡️ Reply El.Ge

📝 Ana Gomes said:

Good afternoon,Can you please send me price and availability of part AZE-CC4Q please?Thank you very much for your time.

➡️ Reply El.Ge

📝 Will LaRue said:

Our Elektronikon Atlas Copco 1900 0700 04 controller is displaying error code 1234 and not responding to commands. Need repair ASAP.

➡️ Reply Elektronikon

📝 Leonard Van den Berg said:

Dear Sir,Ive bought 3 second hand servo drives, EL.GE AZE-CC4Q Tipo AZE LV15/AO-PI am looking for a few weeks for a diagram to connect these, but cant find anything. As well i like to know what is the input voltage.Kind regards,Leonard van den Berg

➡️ Reply El.Ge

📝 Greg Appleby said:

Any results on your search?I have a lot of documentation but it is in French + some in Italian).I bought a second hand drice ex France.are your units branded LV15 or perhaps LV12??pls email me .. we may be of help to each other.Greg Appleby

➡️ Reply El.Ge

📝 DANIEL ZIJLMANS said:

Dear Greg Appleby,I undeerstood you might have documentation of EL.GE drives. I need a electrical diagram for the connection of the following type:EL.GE SD CC 200/49/120Its a DC driveBest regards,Daniel Zijlmans

➡️ Reply El.Ge

📝 Alberto Tavares said:

nesecito por favor del manual de lo variador SD/CC 4º S

➡️ Reply El.Ge

📝 josep said:

Hi.I bought a old cnc mill whit this driver but one is dead.I need the schematics for repair,mny tks, Josep

➡️ Reply El.Ge

📝 Miki gasic said:

i have a damaged servo drive and i need to get it repaired

➡️ Reply El.Ge

📝 Dag A said:

Is there anybody who has a user manual or electric wiring diagram or some information at all on this servodrive ?All help will be very much appreciated ....Best regards Dag ANorway

➡️ Reply El.Ge

📝 Greg Appleby said:

I posted back in 2007. I now have some docmentation includingelectrical diagrams.I can be contacted bee@bee.com.au

➡️ Reply El.Ge

📝 jeff wu said:

Holle !MY DC SERVODRIVE IS NOT GOOD.SO MY MACHINE NOT WORKPARTS : DC SERVODRIVETYPE : AZE-CC4Q1.HOW MONERY ,NEW PARTSTHANKS ! JEFF . 2008.11.07

➡️ Reply El.Ge

📝 pouyan said:

dear siri need the aze-cc4q catalog for LED description and pinoutbest regardspouyan

➡️ Reply El.Ge

📝 AmalleyGekmab said:

When i utilized to obtain high on life but lately Ive accumulated a amount of resistance.

➡️ Reply El.Ge

📝 vernon mudgett said:

on our Stahle air texurizing machine we have a elrest computer . the screen keeps going out on it ,and half to keep reboot the computer to get it to work , we tryed another moniter but it didnt work .the computer is 1994 year.

➡️ Reply Elrest

📝 Andrea said:

We have a old machine with this type of electrical device ,but at the moment it s stopped because i have some wrong signal coming (i think)from servo motor D.C AZE LV15 .when the speed enable signal its sended to AZE device it rest only for a few second and then fall down, this happen when i have more then one device connected and able. If i move the motor in manual everythink ok .I tryed to force the enable signal to all the AZE device but they become crazy ...For this i need ,the electrical drawings of El.ge AZE CC4Q type AZE LV15,the wire connection and in case to know if you can sale me one new device after know the price.

➡️ Reply El.Ge

📝 Fabiola Alvarez said:

We own a Elox HRP-64 machine and we are missing the manual and would like to know it you found one and would like to sell us a copy or tell us where you got it so maybe we could also purchase one.

➡️ Reply Elox Corporation

📝 Jim McNamara said:

You can obtain copies of most Elox manuals by contacting:EDM Zap Part, Inc.1108 Front StreetLisle, IL 60532 USAphone: 630-852-1699fax: 630-852-3678www.edmzap.com

➡️ Reply Elox Corporation

📝 michael lewis said:

We have an Elox edm hrp 64 and i am looking for a manual, filters and DTE 25 oil for it. Any help would be greatly appriciated.Thank youMike

➡️ Reply Elox Corporation

📝 bakr said:

we wont the (bogen-offsetmaschine Elektronische Kontrolleinrichtung, Reflexlichtschranke Ref 102)

➡️ Reply Electron-Machine

📝 carlos orru said:

Dear Srs : recently I purchasse And Elox EDM WIRE MACHINE FROM USA ( Mc Kean Machinery) :and the machine arrived with some electronic problem .the machine is ; Nª serie 718 521 type A O 4b O 219-B211year 1986 -08S/N C -6V0091We do need the ladern diagram ,and also lets me know if you are in condition to supply spares for this macine .rgds carlos

➡️ Reply Elox Corporation

📝 Caleb Walker said:

Hello,We had a bit of a meltdown which damaged the Elox Workmaster 45 jog switch panel. The switches & wires are so fried they are almost un-traceable. Anyway I though you may be able to point me in the direction of a jog switch panel pinout diagram?Best regards,Caleb Walker

➡️ Reply Elox Corporation

📝 RLH said:

We have an ELOX J series wire edm that we need to set the parameters for wire tension and flush control.We had to replace a circuit board and tried to reload the parameters via tape too floppy but with no sucess.Is there a way to load these manually?

➡️ Reply Elox Corporation

📝 ESTUARDO JUAREZ QUIROZ said:

THE SYSTEM OPERATION ERROR.MESSAGE:INSERT DISKET A:PLEASE SEND INFORMATION.BEST REGARDSTHAN YOU.

➡️ Reply Elox Corporation

📝 Jose Aubeyzon said:

We bought an EDM ELOX-AMERITRON here in PERU and planned to start working with it, but at the moment we pressed ON to start it, the sceen shows insert disk and doesn´t work.We would appreciate if you could advice us on how to fix this problem, if need, we would be willing to buy the programming disk required for this machine.Machine ELOX-AMERITRON Cabinet Futura II 50 A N° Serial= F II 50 A- 001025 B.M. N° . VOL 392.6 As this is an urgent matter ,we hope to hear from you as soon as possible,sincerely,Jose Aubeyzon/MODEPSA

➡️ Reply Elox Corporation

📝 Jose Aubeyzon said:

We bought an EDM ELOX-AMERITRON here in PERU and planned to start working with it, but at the moment we pressed ON to start it, the sceen shows insert disk and doesn´t work.We would appreciate if you could advice us on how to fix this problem, if need, we would be willing to buy the programming disk required for this machine.Machine ELOX-AMERITRON Cabinet Futura II 50 A N° Serial= F II 50 A- 001025 B.M. N° . VOL 392.6 As this is an urgent matter ,we hope to hear from you as soon as possible,sincerely,Jose Aubeyzon/MODEPSA

➡️ Reply Elox Corporation

📝 James Dow said:

Jose,it appears that the battery on the motherboard has gone bad. This meansthat the CMOS has to be reprogrammed so that there is no floppy driveand not to seek floppy drive at startup. Also there are other things thatneed change in the CMOS.

➡️ Reply Elox Corporation

📝 KELVIN said:

ELREST solid state relay model: KRD-40/TR-1200B/DS.

➡️ Reply Elrest

📝 MS.KH.CHAN said:

Dear sir,Please quote your best price for new unit KRD-40/TR-1200B/DS or repair ssr PRICE.TQBEST REGARDS,MS.KH.CHAN

➡️ Reply Elrest

📝 Andrew Morandi said:

Dear Sir,Good morning. I had to repair an Elind 6TD20 power supply, but I need characteristics about power transfromer. Could you help me?? Where I can found service manual??Thanks a lot, best regards,Andrew Morandi

➡️ Reply Elind

📝 John Aland said:

Hi, I have a customer with several of these drive units not working.Would it be possible to get these units repaired, at what cost per unit, freight to Australia and turn arround time.Kindest Regards,John.

➡️ Reply El.Ge

📝 Ing. Jose carlos Pinto Aranibar said:

Estimados senores, estamos reparando una seccionadora de madera de giben, cuenta con una placa AZE CC4Q, no sabemos si esta esta bien o mal, les rogaria puedan facilitarnos los pasos a seguir o la secuencia de las entradas o si tubieran un data sheet de esta tarjeta, para ver si podemos hacerla funcionar manualmente, y asi poder revisar el programa en el PLC,a la espera de sus comentarios:

➡️ Reply El.Ge

📝 Henry Guillemin said:

Can you please supply a quote to repair this drive for us. Do you have any repair agents in Auckland NZBest regardsHenry

➡️ Reply El.Ge

📝 GUFFROY said:

I search information on the component LR171E // ELREMCO.Additionnal information DIP14Please send me a email : databook, price, quantity, MOQ, ...

➡️ Reply Elremco

📝 scott smith said:

In cut mode the ram comes down too fast and doesnt pulse. It crashes it the work piece. I adjusted the drift ,didnt help. I tried jumpping the micrometer wires . I sent in the board behined the control modual ( where the fan is ) , it needed some repair but didnt help. I sent the control modual in to have in checked, they said it was good. Checked ohms at the servo, thats o.k. I sent the servo in and they said it had contamination in it. They repaired it but it didnt help. Checked the hydraulic pressure its about 2oo psi. need help thanks, scott

➡️ Reply Eltee Pulsitron

📝 JESUS VAZQUEZ said:

PLEASE CONFIRM IF YOU HAVE RECEIVED THIS EMAILWE NEED IN PARTICULAR THE SERVOVALVE.THANK YOU VERY MUCH.

➡️ Reply Eltee Pulsitron

📝 Leonard Hunter said:

I have ELTEE servovalves in stock. It is generally cheaper to repair your valve. ELTEE used several different valves in the EP30/50 machines. I would need more information about your machine to help you further. L. Hunter

➡️ Reply Eltee Pulsitron

📝 Alex G. said:

Hi,Im looking for the oil pump on a eltee TR20 EP EDM, can you help me with it? or can you point me in the rigth direction?Best RegardsAlex G.

➡️ Reply Eltee Pulsitron

📝 Jonathan said:

I have an Eltee Pulsitron (EP300CP) with a vectoring head. The VMC is displaying that the head should be moving, but the head does not move. Also, the Futaba digital read out for the machine is so worn out that the symbols on the buttons have fallen off. Can you help?

➡️ Reply Eltee Pulsitron

📝 GLENN REVEL said:

I NEED TO ORDER THE SEALS FOR THE RAM ON A ELTEE PULSITRON TR-20. THE NUMBERS/INFORMATION ON THE SEAL: H2 HALLITE #8836210

➡️ Reply Eltee Pulsitron

📝 Howard Hall said:

Are these available for purchase? When changing filters, this gasket tears on occasion

➡️ Reply Eltee Pulsitron

📝 DAVE LIPNICKAS said:

SENDING INFO

➡️ Reply Eltee Pulsitron

📝 william clark said:

We are looking for a new hose for the fluid return. The 3 in. hose from the work area to the fluid holding tank.

➡️ Reply Eltee Pulsitron

📝 terrance shermnan said:

My machine is showing a lot of carbon fragments when running and the result is DC arcs I was told that that weak capasiters csause this problem.

➡️ Reply Eltee Pulsitron

📝 Gary Chance DBA ( POLAR SCALE CO ) said:

Am looking for tech manual for above mentioned instruments . Hard to find as they are very old ... Need to know switch settings to enable print on demand ... Can you help ?

➡️ Reply Electroscale

📝 Steve said:

We are in need of a 1420-ws (or ns) 50 lb load cell for the 30X30 Electroscale base. Please let us know if there are any avenues to explore.Thank you in advance, Steve

➡️ Reply Electroscale

📝 Ramon Martinez Gutierrez said:

tienen refacciones para una erocionadora eltee pulsitron modelo EPR30/RD requiero el cervo motor 4 tarjetas y los planos de la maquina me pueden cotizar la maquina tien aproximadamente 30 anossaludos

➡️ Reply Eltee Pulsitron

📝 CPC ORALU said:

merci de me faire parvenir la documentation dun regulareur de marque ELREST TYPE MPC-01/PT3/KALLF/V2.0/RA/24VDCcordialemenent. deni schmitt

➡️ Reply Elrest

📝 wage karsana said:

PLEASE TELL ME HOW TO GET MANUAL INSTRUCTION OF CAN/LI... 16 KANAL UNIVERSALREGREL ( ELREST)TANKS

➡️ Reply Elrest

📝 Steve said:

We have an Eltee Pulistron EP30/RDP we are looking for filters and manuals for. The power pack serial number is 1292 and the machine serial number is 380. The filters (2) are 6 X 18 with a 2-5/8 hole and a 4-12 fiber gasket top & bottom. They are steel on the outside. Do you carry filters and / or parts and manuals? Would you quote them please, if so.

➡️ Reply Eltee Pulsitron

📝 Joseph said:

I have had this Eltee for maybe 20 yrs.It has been a great machine. Every now and then I get this problem with the ram not coming down to cut,Sometimes just clicking the pulse,or vibration button clears it up.Iyt also seem like it happens more after the machine has been sitting,which is the case now.Can anyone help? The machine is a 1986 ep 30/rdpJoe

➡️ Reply Eltee Pulsitron

📝 Tomas Morita said:

May we get from you the user manual and electrical schematic for the Eltee Pulsitron Model TR-20 (EP-30/RD Control)?Tomas Morita

➡️ Reply Eltee Pulsitron

📝 Scott Wanstrath said:

I am also looking for the user manual and wiring schematic for a Eltee Pulsitron ep30. Please let me know if you found anything, it would be of great help.Scott Wanstrath

➡️ Reply Eltee Pulsitron

📝 Derek Walker said:

I am Looking for Service Manuals & Schematics for Eltee Pulsitron TRM-41 & CNC-30. Looking for information on how the floats are suppose to function when filling the tank and draining the tank.Thank you very much,Derek Walker

➡️ Reply Eltee Pulsitron

📝 robert mcilwain said:

we have a eltee and i need a manual for operation and also machine diagrams

➡️ Reply Eltee Pulsitron

📝 Daniel Espinosa said:

We have a EDM Elox 400 D that when it is pressed the start button the electrodes comeback to home position. Our maintenance crew tried to fix up without success. I wonder if you have a service Engineer that could help us to fix it up.Best Regards(Turbotec is located just 20 minutes from San Diego California.)

➡️ Reply Elox Corporation

📝 Salim Miro said:

I am negotiating to purchase one of your Series O Wire cut EDM machine. I will be shipping it Manila Philippines. Do you have a repair facility in Philippines? If so pleas send the information so we may contact them. Thank you,

➡️ Reply Elox Corporation

📝 Brad Bagwell said:

hello,we have an Eltee Pulsitron EP30/RD and were needing a maintenace and operations manual,do have these and if not do you know where we could get them? thank you.

➡️ Reply Eltee Pulsitron

📝 NILEAYSH GHODAKE said:

I have an issue with my Electronic Systems Of Wi 35-1050-0 where its not powering on at all. Looking for a repair technician who can diagnose and fix the problem

➡️ Reply Electronic Systems Of Wi

📝 sam holcomb said:

The Z axis stoped working.Any ideas to what caused this or how to fix it?

➡️ Reply Eltee Pulsitron

📝 Omar said:

Hi.Im looking for some wiring diagrams for Eltee Pulsitrons EP30/RD controller. Any help or insight you can provide would be greatly appreciated.Best regards,Omar

➡️ Reply Eltee Pulsitron

📝 Omar said:

Hi.Im looking for some wiring diagrams for Eltee Pulsitrons EP30/RD controller. Any help or insight you can provide would be greatly appreciated.Best regards,Omar

➡️ Reply Eltee Pulsitron

📝 Sergio González said:

need manuals de machine Edm eltee pulsatrion Ep 300 Cotitation pleas all the manuals operativos and electrical

➡️ Reply Eltee Pulsitron

📝 Ernesto Rangel said:

I need help with a machine model Serial M-3 W/DA-000024 BMNO V05.256.9 and required support, are you have contact in Mexico an dis possible send me phone Thanks

➡️ Reply Elox Corporation

📝 Kyle Herd said:

I have a DT-260 unit with intermittent power issues. It will power on and shut off at will before the normal time out and has an opinion of its own when it would like to turn on in general.I have a small amount of spare parts from an older unit, but I am unable to determine the root cause of the power problem.I was wondering if this is a routine issue and if so/not what an estimeted repair cost would be.

➡️ Reply Electro-Nite

📝 Becky said:

Im trying to find a manual for an Agie Futura II Mondo I.

➡️ Reply Elox Corporation

📝 manseur said:

Bonjour,Je cherche des schemas electroniques pour les variateurs ETAZIRT(sangiacomo fantazia)

➡️ Reply Elec Eltek

📝 manseur said:

bonjours,Je suis a la recherche des schemas electroniques DINEMA1- ECODD 15 (PCB3832C)2- PCB 20073- PCB 2008

➡️ Reply Elec Corp Of America

📝 Ron Clausen said:

we have a Mondo Start 50, ser # M50 STAR-002181, another is U06.690.8 would like to know how many gals of fluid does it take and /or a downloadable manual.Thanks

➡️ Reply Elox Corporation

📝 SHERRI BROOKS said:

I HAVE A CUSTOMER WHO HAS REQUESTED REPAIR OF ELPAC M/N 1588 INPUT 105-125/210-250, OUTPUT 12 VDC,5VDC,&18VDC. IT HAS A MANUFACTURES DATE OF 02-23-79 ON THE UNIT. ALSO ON THE UNIT IS THE NAME CINCINNATI MILACRON S/N 51-CENT15F-0047. ANY ADVISE OR HELP WITH THIS WOULD BE GREATLY APPRECIATED.SHERRI BROOKSELECTRICAL AUTOMATION SALES & SERVICE224 STATE ST.JACKSON, TN. 38301PH# 731-410-8141FAX# 731-554-2581

➡️ Reply Elpac

📝 sergio garcia said:

I have a edm elox workmaster 45 whit futura 50 control,but when I buy the machine it came whit some disconnected wires inside the controls and I have not any kind of electrical wiring diagram or any manual for this machine,I wold like to get that manual books, please send me quotation for all manual books,operation,maintenance,wiring diagrams,mechanical,etc.Please help me.Macine information:ELOX WORKMASTER 45TYPE:FUTURA 50SERIAL:PS-1426BMN°:18310-14

➡️ Reply Elox Corporation

📝 Ruben Balucas said:

Sir, Please send me a copy of the operation manual of the mentioned TOYO DENKI INVERTER. ( VF61V-2222-W1 )As of now I am experiencing an error which I dont know what was it because i dont have any manual for the unit.Thank youRuben

➡️ Reply Elektro Mechanik Elektron Bremen

📝 dave brancato said:

would you be interested in repairing 3 lutron dimmer cards?

➡️ Reply Elo Touchsystems Inc

📝 John said:

Hello, my name is John with Machinery Support in Cincinnati, Ohio. Im in need of a repair/parts manual for the TR20 model Eltee Pulsitron EDM. If you can quote me your price on this machine manual as soon as you have the time Id appreciate it greatly. Thank you for your time and consideration, have a good day.

➡️ Reply Eltee Pulsitron

📝 JamesNok said:

Subject Urgent Request for Repair Info for Electro Craft 9101-1132Hi there,Our Electro Craft 9101-1132 has stopped working and we urgently need repair information to get it back up and running. We are unable to find a replacement and need guidance on fixing the issue. Any assistance would be greatly appreciated.Thank you.

➡️ Reply Electro

📝 terrance sherman said:

What type and weight of hydraulic oil to use in the hydraulic sending unit located beneith the base cabnett in the bottom of the machine. The oil was red in color? Please help us and do you have o-rings seals for the head of machine and also a bellows cover to seal head ? upper and lower?

➡️ Reply Eltee Pulsitron

📝 Claude Auman French said:

The ELCOM EASYFD600R32 SERVO DRIVE at the warehouse is exhibiting unusual behavior - it is acting erratically and not functioning as it normally does. The unit seems to be malfunctioning, but further details regarding the specific issues experienced would be helpful in diagnosing and resolving the problem efficiently.

➡️ Reply Elcom

📝 Wayne Lacouture said:

I am looking for a electrical diagram for my ELOX machine it is a SYS-11 CEF50 I am mainly concerned about the power cables to the cutting head the complete power circuit.Thank you,Wayne LaCouture

➡️ Reply Elox Corporation

📝 Craig Nelson said:

The Eldetco Inc 2100B E50200 feed controller is not responding to input commands. Need assistance to diagnose and repair urgently.

➡️ Reply Eldetco Inc

📝 Ariel Rodriguez Reyes said:

Hello:I have a machine:ELTEE PULSITRON ep300cpMOD. TR21 i need operationg manual, and diagrams and instruction manual.Can you help me with this???

➡️ Reply Eltee Pulsitron

📝 daz said:

Subject Persistent Issue with Eldetco Inc. E50200 Drive UnitDear Repair Shop,As the Inventory Manager for our organization, I want to bring to your attention a recurring problem with the Eldetco Inc. E50200 drive unit. I have noticed that this particular unit has been consistently returned or reported by our customers.Based on the records, and as communicated by our technicians, it appears that there might be a systemic issue with this specific model. We would appreciate it if you could thoroughly assess and address this issue to prevent any further inconvenience to our customers.Thank you for your attention to this matter.Best regards,Inventory ManagerEldetco Inc.

➡️ Reply Eldetco Inc

📝 Cheap_Insurance said:

Elrest 85049165 unit not powering on when activated. Need assistance with troubleshooting and repair. Please respond

➡️ Reply Elrest

📝 Huan Le said:

I am experiencing a problem with my Elcom A80ER-HE Card Reader/Writer. The unit is not reading any cards and fails to write to them as well. Whenever I try to use the device, nothing happens, and it seems unresponsive. I have tried using different cards, but the issue persists. Based on the troubleshooting Ive done, it appears that there is a hardware malfunction that is preventing the unit from functioning properly. In terms of estimated replacement cost, I am unsure, but I am hoping to get a quote for repair services to determine the most cost-effective solution to restore the functionality of my Elcom A80ER-HE Card Reader/Writer.

➡️ Reply Elcom

📝 Knud Oellgaard said:

The Elektronikon Atlas Copco 1900 0700 03 digital readout is failing to display any information despite power being supplied. Urgently seeking repair service for immediate assistance.

➡️ Reply Elektronikon

📝 Eric Liseno said:

We are having an issue with our Eltee EP30/RD EDM. Serial Number 1268. The operator called me out saying the machine was arcing. When I got out there, the part they are burning is contained in a fixture, and the whole top of the fixture starts glowing red immediately when the electrode touches the part and smoke comes rolling out of it. They even tried shutting off all the amp switches on the front panel and it still did the same thing. I pulled all the boards to inspect and clean. I also checked all the fuses and no luck. It seems like something is shorted or there is a bad board. Could you please send me an email with what else I could check or if you need any more info?

➡️ Reply Eltee Pulsitron

📝 Jon Surma said:

Do you repair Electro Matic Travatrol Model # TRS4-5E

➡️ Reply Electro-Matic

📝 Ed Ransom said:

I have an Eltee EP/30 RDP that the head is out of tram. Can you tram the head on these or are they fixed?

➡️ Reply Eltee Pulsitron

📝 KUMAR .P said:

Electro-Craft 9101-1132 not powering on, no display or response. Need immediate repair assistance. Thank you.

➡️ Reply Electrocraft

📝 Michael Munroe said:

It sounds like the circuit board in your Electronic Visions Co. GESPAC SBS-6AH256 unit is exhibiting unusual behavior. Can you provide more details on how its acting weird? For example, are there any strange sounds, error messages, lights flashing, or functions not working as they should? The more information you can provide, the better I can assist you in troubleshooting and finding a solution.

➡️ Reply Electronic Visions Co