Welcome to El.Ge

unofficial service & repair forum

We repair a wide range of El.Ge Equipment.

Ask questions, or call 1-336-969-0110 for faster service.

Use the search bar above to find specific manufacturers.

• 40+ years of experience repairing Industrial & Commercial units
• Certified Senior Industrial Electronics Technician
• Ability to do Reverse Engineering
• No job to big or small
• Fast turn around time on most units
• Quality of work comes before profit!
• Old Fashion Customer Service is always the right policy
• Extended warranty
• Fair Estimates
• Low Prices

🛠️ Common AI Repair Summaries 🏭

Comments for El.Ge

📝 Sean Moffatt said:

I have one of these units in a servo roll feed that drives the brushed DC servo motor just fine. The problem is that it does not respond to the +/- 10V control signal. It runs at 100% randomly in fwd or rev when a start signal is applied. The cnc controller was made in the 80s It is no longwer supported (software or electronically), and is basically junk and is going to be replaced with something that is current. I need a estimate for testing and or repairs if possible. Model: AZE-CC4QTipo:AZE LV15/AO-P-110/8,5/24No. Matr.EC 22230Codice:42/88ThanksSean MoffattOperations managerHoffman Mint

➡️ Reply El.Ge

📝 MARKO said:

I NEED COMPLET DC SERVODRIVE EL.GE AZE-CC4Q.PLEASE SEND ME OFFER.

➡️ Reply El.Ge

📝 Ing. Jose Calos Pinto said:

Estimados, tengo que reparar una maquna giben con un controlador AZE-CC4Q, esto es en bolivia, pero no hay informaion aerca de la plaza y su funcionamiento para la secuencia de trabajo, favor ayudarme con este dilema

➡️ Reply El.Ge

📝 Sven Rookie said:

Iv a question regarding the controller:Are there any spare parts for those drives, is there any technical support existing or is there any identical drive which can be used?As USA is quite far away - do you know a technical support in europa?Many thanks for your answer!Kind regardsSven

➡️ Reply El.Ge

📝 mick Sharman said:

There are no spares anywhere. The Poletti & Osta brand is the same, just badged and coloured differently. They are the same as El.ge. identical.You can exchange any higher current rating (average and Peak) as long as it is higher rated, but same Voltage. I could not find any of these, but there was a supplier in UK who had one, but I think it has gone.

➡️ Reply El.Ge

📝 Vlade Vujovic said:

Molim Vas za pomoc,imam cnc morbideli u 15 i ne radi mi DC servodrive Y osa,type AZE-cc4q el.ge,Milano.tipo AZE HV 12/AO-R-200/6,5/18NMATR EC 19613 CODICE 16/88Interesuje me da li imate i kolika je cena?pozdrav i hvala,Vlade

➡️ Reply El.Ge

📝 Ana Gomes said:

Good afternoon,Can you please send me price and availability of part AZE-CC4Q please?Thank you very much for your time.

➡️ Reply El.Ge

📝 Leonard Van den Berg said:

Dear Sir,Ive bought 3 second hand servo drives, EL.GE AZE-CC4Q Tipo AZE LV15/AO-PI am looking for a few weeks for a diagram to connect these, but cant find anything. As well i like to know what is the input voltage.Kind regards,Leonard van den Berg

➡️ Reply El.Ge

📝 Greg Appleby said:

Any results on your search?I have a lot of documentation but it is in French + some in Italian).I bought a second hand drice ex France.are your units branded LV15 or perhaps LV12??pls email me .. we may be of help to each other.Greg Appleby

➡️ Reply El.Ge

📝 DANIEL ZIJLMANS said:

Dear Greg Appleby,I undeerstood you might have documentation of EL.GE drives. I need a electrical diagram for the connection of the following type:EL.GE SD CC 200/49/120Its a DC driveBest regards,Daniel Zijlmans

➡️ Reply El.Ge

📝 Alberto Tavares said:

nesecito por favor del manual de lo variador SD/CC 4º S

➡️ Reply El.Ge

📝 josep said:

Hi.I bought a old cnc mill whit this driver but one is dead.I need the schematics for repair,mny tks, Josep

➡️ Reply El.Ge

📝 Miki gasic said:

i have a damaged servo drive and i need to get it repaired

➡️ Reply El.Ge

📝 Dag A said:

Is there anybody who has a user manual or electric wiring diagram or some information at all on this servodrive ?All help will be very much appreciated ....Best regards Dag ANorway

➡️ Reply El.Ge

📝 Greg Appleby said:

I posted back in 2007. I now have some docmentation includingelectrical diagrams.I can be contacted bee@bee.com.au

➡️ Reply El.Ge

📝 jeff wu said:

Holle !MY DC SERVODRIVE IS NOT GOOD.SO MY MACHINE NOT WORKPARTS : DC SERVODRIVETYPE : AZE-CC4Q1.HOW MONERY ,NEW PARTSTHANKS ! JEFF . 2008.11.07

➡️ Reply El.Ge

📝 pouyan said:

dear siri need the aze-cc4q catalog for LED description and pinoutbest regardspouyan

➡️ Reply El.Ge

📝 AmalleyGekmab said:

When i utilized to obtain high on life but lately Ive accumulated a amount of resistance.

➡️ Reply El.Ge

📝 Andrea said:

We have a old machine with this type of electrical device ,but at the moment it s stopped because i have some wrong signal coming (i think)from servo motor D.C AZE LV15 .when the speed enable signal its sended to AZE device it rest only for a few second and then fall down, this happen when i have more then one device connected and able. If i move the motor in manual everythink ok .I tryed to force the enable signal to all the AZE device but they become crazy ...For this i need ,the electrical drawings of El.ge AZE CC4Q type AZE LV15,the wire connection and in case to know if you can sale me one new device after know the price.

➡️ Reply El.Ge

📝 John Aland said:

Hi, I have a customer with several of these drive units not working.Would it be possible to get these units repaired, at what cost per unit, freight to Australia and turn arround time.Kindest Regards,John.

➡️ Reply El.Ge

📝 Ing. Jose carlos Pinto Aranibar said:

Estimados senores, estamos reparando una seccionadora de madera de giben, cuenta con una placa AZE CC4Q, no sabemos si esta esta bien o mal, les rogaria puedan facilitarnos los pasos a seguir o la secuencia de las entradas o si tubieran un data sheet de esta tarjeta, para ver si podemos hacerla funcionar manualmente, y asi poder revisar el programa en el PLC,a la espera de sus comentarios:

➡️ Reply El.Ge

📝 Henry Guillemin said:

Can you please supply a quote to repair this drive for us. Do you have any repair agents in Auckland NZBest regardsHenry

➡️ Reply El.Ge