Welcome to Elox Corporation

We repair a wide range of Elox Corporation Equipment.

Ask questions, or 1-336-969-0110 for faster service.

Use the search bar above to find specific manufacturers.

• 40+ years of experience repairing Industrial & Commercial units
• Certified Senior Industrial Electronics Technician
• Ability to do Reverse Engineering
• No job to big or small
• Fast turn around time on most units
• Quality of work comes before profit!
• Old Fashion Customer Service is always the right policy
• Extended warranty
• Free Estimates
• Low Prices

No repair summaries available yet for this manufacturer.

Comments for Elox Corporation

📝 Michael Hendrick said:

Hell I was left a EDN ELOX HRP 64 and I would like to get some info on this machine. I dont even know if it works. If there is somewhere I could uptain or even better down load a manual I would be so much in your dept. Thanks Michael Hendrick— Purchase or Repair:

➡️ Reply Elox Corporation

📝 Fabiola Alvarez said:

We own a Elox HRP-64 machine and we are missing the manual and would like to know it you found one and would like to sell us a copy or tell us where you got it so maybe we could also purchase one.— Purchase or Repair:

➡️ Reply Elox Corporation

📝 carlos orru said:

Dear Srs : recently I purchasse And Elox EDM WIRE MACHINE FROM USA ( Mc Kean Machinery) :and the machine arrived with some electronic problem .the machine is ; Nª serie 718 521 type A O 4b O 219-B211year 1986 -08S/N C -6V0091We do need the ladern diagram ,and also lets me know if you are in condition to supply spares for this macine .rgds carlos— Purchase or Repair:

➡️ Reply Elox Corporation

📝 Daniel Espinosa said:

We have a EDM Elox 400 D that when it is pressed the start button the electrodes comeback to home position. Our maintenance crew tried to fix up without success. I wonder if you have a service Engineer that could help us to fix it up.Best Regards(Turbotec is located just 20 minutes from San Diego California.)— Purchase or Repair:

➡️ Reply Elox Corporation

📝 Salim Miro said:

I am negotiating to purchase one of your Series O Wire cut EDM machine. I will be shipping it Manila Philippines. Do you have a repair facility in Philippines? If so pleas send the information so we may contact them. Thank you,— Purchase or Repair:

➡️ Reply Elox Corporation

📝 Ernesto Rangel said:

I need help with a machine model Serial M-3 W/DA-000024 BMNO V05.256.9 and required support, are you have contact in Mexico an dis possible send me phone Thanks— Purchase or Repair:

➡️ Reply Elox Corporation

📝 Becky said:

Im trying to find a manual for an Agie Futura II Mondo I.— Purchase or Repair:

➡️ Reply Elox Corporation

📝 Ron Clausen said:

we have a Mondo Start 50, ser # M50 STAR-002181, another is U06.690.8 would like to know how many gals of fluid does it take and /or a downloadable manual.Thanks— Purchase or Repair:

➡️ Reply Elox Corporation

📝 sergio garcia said:

I have a edm elox workmaster 45 whit futura 50 control,but when I buy the machine it came whit some disconnected wires inside the controls and I have not any kind of electrical wiring diagram or any manual for this machine,I wold like to get that manual books, please send me quotation for all manual books,operation,maintenance,wiring diagrams,mechanical,etc.Please help me.Macine information:ELOX WORKMASTER 45TYPE:FUTURA 50SERIAL:PS-1426BMN°:18310-14— Purchase or Repair:

➡️ Reply Elox Corporation

📝 Wayne Lacouture said:

I am looking for a electrical diagram for my ELOX machine it is a SYS-11 CEF50 I am mainly concerned about the power cables to the cutting head the complete power circuit.Thank you,Wayne LaCouture— Purchase or Repair:

➡️ Reply Elox Corporation