Excell is a manufacturer specializing in precision machining components for a wide range of industrial applications. They are known for their high-quality products that meet strict industry standards and their ability to provide custom solutions for complex engineering challenges. [AI]
We repair a wide range of Excell Equipment.
Ask questions, or 1-336-969-0110 for faster service.
Use the search bar above to find specific manufacturers.
No repair summaries available yet for this manufacturer.
Dear Sir/Madam,Ive lost my Excellone CNC-6 with EX-110 Operating System and Softwarehow can i purchase or download this?➡️ Reply Excellon Automation
dear sir,we are mfg pcb in india we have 4 machine excellonwe need two number vdc(vidio display card) & one repairingwe also need sofware original for ex-300 machinethanking you,your faithfully,gmcparesh patel➡️ Reply Excellon Automation
we also need sofware original for ex-300 machineSERGIOAJI123@HOTMAIL.COM;SERGIOEMPRESA@HOTMAIL.COM➡️ Reply Excellon Automation
dear sir,we are mfg pcb in india we have 4 machine excellonwe need two number vdc(vidio display card) & one repairingwe also need sofware original for ex-300 machinethanking you,your faithfully,gmcparesh patel➡️ Reply Excellon Automation
Dear Sir/Madam,Ive lost my Excellone CNC-6 with EX-300 D/R Operating System and Softwarehow can i purchase or download this?HELP➡️ Reply Excellon Automation
i need manual for excellon ex 300.➡️ Reply Excellon Automation
WE NEED HARD DISK FOR OUR EXCELLON DRILLER/ROUTER CNC 6 EX200 MACHINE WITH BOOTABLE FEATURE.➡️ Reply Excellon Automation
Dear Sir,I have one system 2000s excellon machine with cnc 07 console.I have a problem related software.I have installed four floppy in machine but after bootiung machine again it reboot system automatically.and if I remove the I/O-1 board power then it but full software but in mach file it shows concept machine even this machine is system 2000s and I dont have any system bckup floppy. so how can i make new system backup floppy.➡️ Reply Excellon Automation
Dear Sir/Madam,Ive lost my Excellone CNC-6 with EX-300 Operating System and Softwarehow can i purchase or download this? 1. WE NEED HARD DISK FOR OUR EXCELLON DRILLER/ROUTER CNC6 EX300 MACHINE WITH BOOTABLE FEATURE. 2. we also need sofware original for ex-300 machine3. SOFWARE EX-300 D/R 4. HARD DRIVE : 20MB O 20 GB. P/N:910573-155.HARD DISK CONTROLLER DTC-86: P/N: 409059-176.SYSTEM OPERATIONS.ATT:Carlos Alarcon Axys SA.➡️ Reply Excellon Automation
Display screen of the control panel shows the value of memory registers and do not boot the machines from any of the floppy drives. We also have tried to reset and boot it manually by BO,0 and BO,1 commands as given in the manuals. What might be the problem and how to solve it. Looking forward for a positive reply.Regards➡️ Reply Excellon Automation
sir my vdc card is proc➡️ Reply Excellon Automation
Once machine boots, home page shows error code as faulty limit switch , right travel limit➡️ Reply Excellon Automation
Dear Sir, I have a problem with our XL5 D/R. TheD/R software will not run although i can run a MK V drilling software. Do you know what revision software the XL5 D/R should be running? and do you have any idea why the drilling software for MK V or EX200 will run but the D/R software will not. Many thanks for any help you can give me. I am using a CTES system behind the reader.Regards Peter➡️ Reply Excellon Automation
Dear Sir, need excellon cnc6 cpu cord ,please send quote. Thanking you. sivaramakrishna.d M.S.ELECTRONICS. PHONE.+91-9293159245 +91-40 32585812➡️ Reply Excellon Automation
Contact Tim with PCB Machine ServicesHe works on Excellon Equipment and has helped me out a few times.Email: Tim@PCBMachineServices.com➡️ Reply Excellon Automation
Industrial Electronic Repair
145 Rockwell Place Ct
Tobaccoville, NC 27050
🚑 Rush repair shipments only — no walk-ins.
Industrial Electronic Repair
931-E S. Main St #204
Kernersville, NC 27284
📦 Mailing Address (for invoices or shipped repairs)
No walk-ins accepted.