Welcome to I

We repair a wide range of I Equipment.

Ask questions, or 1-336-969-0110 for faster service.

Use the search bar above to find specific manufacturers.

• 40+ years of experience repairing Industrial & Commercial units
• Certified Senior Industrial Electronics Technician
• Ability to do Reverse Engineering
• No job to big or small
• Fast turn around time on most units
• Quality of work comes before profit!
• Old Fashion Customer Service is always the right policy
• Extended warranty
• Fair Estimates
• Low Prices

🛠️ Common AI Repair Summaries 🏭

Comments for I

📝 Sales Service said:

If you need your unit tested or repaired then give us a call.We offer fair estimates and offer extended warranties.You can contact us at 1-(336)-969-0110Shipping/ReceivingIndustrial Electronic Repair931-E S. Main St #204,Kernersville, NC 27284 Phone: (336) 969-0110We repair industrial electronic devicesIf you have an industrial electronic device that needs repair,Feel free to contact us!

➡️ Reply Industrial Electronics Repair

📝 Francisco said:

I have 2 Goring-Kerr (Thermo Fischer Scientific) DSP2 metal detectors that show the following faults in the status page: Faults: 3 Product memory - search head - RF board. I do not have the operator/supervisor/Engineer passwords and the password seed numbers are (what I assume is by default): Operator: 12345678 Supervisor:23456781 Engineer: 34567812. I have tried using password ZBZB but it does not work. Conveyor belt turns on and off and red fault light is on. Any suggestions? Thanks in advance.

➡️ Reply Industrial Electronics Repair

📝 DonaldBox said:

telegram virtual numbers

➡️ Reply Industrial Electronics Repair

📝 Lynn said:

New Feedback Report Name: Lynn Location: n/a Department: N/A Price Rating: ⭐⭐⭐⭐⭐ Service Rating: ⭐⭐⭐⭐⭐ Support Rating: ⭐⭐⭐⭐⭐ Message: Thank You for repairing our drive and fast turn around.

➡️ Reply Industrial Electronics Repair

📝 Victor said:

I need a driver for IDEKi_yama monitor. OS Windows 2000/XP.Thank you.

➡️ Reply Ideki-Yama

📝 Shop said:

After much searching unable to find the drivers that you need for the IDEKi yama monitor with the information you provided. You need to hook it up to a sencore to find the specs that your monitor can handle and then select a close enough monitor driver with regards to the specs of a supported driver in XP that can handle the monitor you have.

➡️ Reply Ideki-Yama

📝 Visalia Electric Motor Shoop said:

We have a model# 345 IRD Mechanalysis Balancer and we need to have it repaired. Do you repair these machines.Please let me know.Lisa Woodhouse

➡️ Reply Ird Mechanalysis

📝 Craig Jackson said:

I need an operating manual for an IRD Mechanalysis Model 345. Can I get one scanned and emailed as a PDF file?

➡️ Reply Ird Mechanalysis

📝 ANAS said:

DEAR I NEED A MANUAL BOOK OG IRD MECHANALYSIS WITH MODEL 880. BECAUSE I HAVE A IRD MECHANALYSIS BUT NO MANUAL BOOK. I NEED THE LESSON ABOUT THE BASIC OF VIBRATION MODULE 1 AND MODULE 2. I NEED IT FOR LEARNING ABOUT VIBRASTION..THANKYOU

➡️ Reply Ird Mechanalysis

📝 Anas effendi said:

NEED A MANUAL BOOK OG IRD MECHANALYSIS WITH MODEL 880. BECAUSE I HAVE A IRD MECHANALYSIS BUT NO MANUAL BOOK. I NEED THE LESSON ABOUT THE BASIC OF VIBRATION MODULE 1 AND MODULE 2. I NEED IT FOR LEARNING ABOUT VIBRATION..THANKYOU

➡️ Reply Ird Mechanalysis

📝 mohit bansal said:

SIR WE ARE USING IRD MECHANALYSIS 880 MODEL HERE IN NTPC AURAIYA. BUT NOWDAYS IT IS GIVING PROBLEM WHILE CHARGING. SO PLEASE PROVIDE ME REPAIR MANUAL SO THAT WE CAN REPAIR OUR EQUIPMENT

➡️ Reply Ird Mechanalysis

📝 ertac hurdogan said:

DEARI NEED A MANUAL BOOK Of IRD MECHANALYSIS WITH MODEL 246. BECAUSE I HAVE A IRD MECHANALYSIS BUT NO MANUAL BOOK. THANKYOU

➡️ Reply Ird Mechanalysis

📝 cristian ghita said:

. Data processing (diagnosis) with Amethist 1.01 program- data were taken over from the data collector 890 IRD Mechanalysis(England). Operating the data collector 890, model7090 PMP software, according to ISO 2372.

➡️ Reply Ird Mechanalysis

📝 Jose Sanchez said:

necesito por favor el manual de usuario de este modelo ird 880 mechanalysis, en espanol

➡️ Reply Ird Mechanalysis

📝 Carlos Eduardo Franco said:

Dear sirs:Please send me information and operation manual of IRD 345 mechanalisys.Very truly yours,carlos Eduardo Franco G.MECHANICAL ENGINEER

➡️ Reply Ird Mechanalysis

📝 ISAAC SINYANGWE said:

We are currently using Model 290 IRD (c) 1998 Mechanalysis Balancer and we are in a position of not knowing what to do with the machine whether to have it repaired or only calibration is required.This is what we are experiencing:-the machine is not responding to the weights initially indicated as requiredthe machine is not giving the actual speed.

➡️ Reply Ird Mechanalysis

📝 Ivana Hrazdilova said:

Good Morning,tell me please, if you are possible to delivery us spare parts for this equipment, producer I.A.G. Elettronica; Via Passera 2; 28100 Novara - No.We need necessary an operation panel. Excuse me please my english language, if you can speak german, will it be better for me.I thank you for your help in advance and wish you a nice day!Ivana Hrazdilova

➡️ Reply I.A.G. Elettronica

📝 Carine MONTOYA said:

Hello,We have an unserviceable Institut Dr Forster material P/N 2-164.Have you got capabilities to repair this material ?If you could, please send us an average repair cost with delivery time.Best regards,Carine MONTOYATAT INDUSTRIES FNI CIPPhone : 00689 86 35 80Fax : 00689 83 66 07

➡️ Reply Institut Dr. Forster

📝 RIEGEL ROLAND said:

DO YOU HAVE THE POSSIBILITY TO CALIBRATE OUR DEFECTOSCOP P/N SD2.832.01-1001 AND PLEASE COULD YOU GIVE ME A PRICE FOR THIS OPERATION?

➡️ Reply Institut Dr. Forster

📝 Daniel Salas said:

Por favor quisiera saber cuanto costaria la reparacion de mi equipo y calibracion. gracias atentamenteDaniel Salas

➡️ Reply Institut Dr. Forster

📝 Brodar Damir said:

Dear, Since my company, called Brodarski Institute that is located in Zagreb, Croatia, owns Magnetometer 1.131 - 12 manufactured by Institut dr. Forster and we are going to do serious measuremets of magnetic field, I would be very pleased if You could send me its manual and specifications on English leanguage on my e-mail adress. This would be very helpful to me and my colleagues.Best regards,Brodar Damir, B.SC.El.Eng.Department of Civil EngineerigBrodarski Institute d.o.o.Av. V. Holjevca 2010 020 ZagrebTel: 01/6504-268Fax: 01/6504-300E-mail: damir.brodar@hrbi.hrwww.hrbi.hr

➡️ Reply Institut Dr. Forster

📝 firdaus said:

Dear Sir/MadamMy name is Mohd Firdaus from PE System Distribution Sdn Bhd. Im actually looking a sensorfor in house metal detector.I would need 17 unit of this sensor. I understand that you may havethe product as listed in the website. Can you send more information on this aswell as the quatation. Please call me if you need more information on thisenquiry. Thanks.Mohd FirdausPE System Distribution Sdn Bhd0175123163

➡️ Reply Institut Dr. Forster

📝 Graeson Gerry said:

Could you please assist us with the following?We are in search for the calibration procedure for this unit?Details can be sent to electrical.workshop@gammatecsa.comKindest RegardsGraeson Gerry

➡️ Reply Institut Dr. Forster

📝 JOSE ESTIMA said:

Having a good dayWe are an Airline Company, and we have two equipment that need calibration. The equipment are working as well as have received, what do you suggest for these equipment calibration due to the Authorities Regulations for the acceptance.

➡️ Reply Institut Dr. Forster

📝 Devina Kistamah said:

Dear Sir/MadamWe have the subject manual in our possession at original issue and would liketo know if it has been revised to a new manual. if email is wrongly addressed please redirect and revert to us.Thank you

➡️ Reply Institut Dr. Forster

📝 Zoran Blagojevic said:

DearWe do not have user manual and calibration devices defektometer H 2.835. If e-mail sent to wrongly adressed please redirect and return to us.thank you

➡️ Reply Institut Dr. Forster

📝 m.h.javadi said:

please send me the calibration procedure for defectometer 2.837.thanks

➡️ Reply Institut Dr. Forster

📝 Johnson said:

We are urgently in need of a defectomat for one of our plants a defectomat DS 2.815 with ferromat channel along with complete accessories. Pl arrange to forward your quote immediately

➡️ Reply Institut Dr. Forster

📝 SLAVOJKA STRUNJAS said:

Please,SEND ME OFFER FOR :CABLE FROM DEFECTOMAT TO COIL/ DEFECTOMAT CP 2.842DMCP 1.1DR. FORSTER

➡️ Reply Institut Dr. Forster

📝 Elidio Schiavon said:

TEMOS PARA VENDA CABOS( CABLES ) E UM DEFECTOMAT FOERSTER MODELO 2.842 POUCO USO ELIDIOSCHIAVON@GMAIL.COMelidio.schiavon@terra.com.br

➡️ Reply Institut Dr. Forster

📝 Desmond Goh said:

Izumi Denki Japan , AC meter, 0300 amp , or 0600ampClass 2.5 , No. AK G4Dia. 65 M2 roundType M20, C.T 200/1A

➡️ Reply Idec Izumi Corp.

📝 Bode Abdulkareem said:

Please send your contact address and email to enable us to place order.

➡️ Reply Idec Izumi Corp.

📝 Jacob Halim said:

Dear Sir, PLEASE KINDLY QUOTE US YOUR BEST FOB PRICE FOR THE FOLLOWING ITEM :1. -8- EA PUSH BOTTON SWITCH P/N : ABN501 VOLT : 110 V MFR : IZUMI DENKI AWAITING YOUR PROMPT REPLY ASAP. READY STOCK OR NOT?PLEASE CALCULATE THE TOTAL GROSS WEIGHT?THANK YOU REGARDS,JACOB HALIMPT. FAJAR SELATANTEL ; 62-711-351523FAX : 62-711-369858

➡️ Reply Idec Izumi Corp.

📝 Anilkumar said:

Dear sir,I have to get some push butoon switches (IZUMI MCM23-M, IZUMI DENKI CORP.) . Is there any possibility to get the same from united arab emirates. It is an urgent requirement.Your valuable reply will be appreciatedAnilkumar

➡️ Reply Idec Izumi Corp.

📝 MUHAMMED KABIR said:

PLEASE QUOTE YOUR BEST PRICE AND DELIVERY TIME INCLUDING GROSS WEIGHT.ITEM1.LIGHT INDICATING,RED 200/220V.#APN-128R-------16EACHTHANKSMUHAMMED KABIRSALMAN ALI AL FARAJ ESTJUBAIL.SAUDI ARABIA

➡️ Reply Idec Izumi Corp.

📝 rumanto said:

tolong sampaikan kepada kami daftar harga bersih per unit plus biaya pengiriman untuk produk push bottom, CAN-4110650, AC 125V-5A, AC 300V-3A, 19310N red cover

➡️ Reply Idec Izumi Corp.

📝 rumanto said:

tolong sampaikan kepada kami daftar harga bersih per unit plus biaya pengiriman untuk produk push bottom, CAN-4110650, AC 125V-5A, AC 300V-3A, 19310N red cover, manufaktur izumithanksrumantoPerum taman gading blok C/ no.248cilacap, indonesia

➡️ Reply Idec Izumi Corp.

📝 I.ANDI PRANOTO said:

Dear sir,Could I get the price for :POWER SUPPLYVOLTAGE : 100-200VFREQUENCY : 50-60HZSERIAL NUMBER : 33610PART NO : ANPT - G8NMANUFACTURE : IZUMI DENKI COqty : 1 eachCould you please also inform the air freight cost to Singapore ?Thank you,Best regards,I.Andi PranotoPT.Radis MerahJl.Alam Segar II/1Pondok Indah Jakarta 12310

➡️ Reply Idec Izumi Corp.

📝 Chris Carley said:

We have a electronic slave uit that failed recently. we would like to find out more information on it regarding either warranty available or repair/rebuild capabilities.Model: T2-D10-888-K7S/N: 33030025Application: MCI D4500 Motor CoachThank youChris

➡️ Reply I/O Controls Corp.

📝 as_shad said:

dear hiI want data sheet superelf-terminalino rs485/rs232 please.

➡️ Reply I/O Controls Corp.

📝 Addiniamync said:

I need a driver for my phillips snn6500 wireless netcardor smc2632 wireless net cardI cant make them run on linpus linux liteplease helpregardsAddiniamync

➡️ Reply I/O Controls Corp.

📝 Phelumsgese said:

I need a driver for my phillips snn6500 wireless netcardor smc2632 wireless net card.I cant make them run on linpus linux lite.Please help.Regards,Addiniamync

➡️ Reply I/O Controls Corp.

📝 Scot said:

Inductotherm 804237 circuit board experiencing intermittent power loss, causing disruptions in industrial unit operation. Need immediate assistance for repair.

➡️ Reply Inductotherm

📝 Lcpl of Marines said:

ToInstitutDr.ForsterI am a technician and my shop is in possession of a few of your search instrument FEREX 4.021 (models K,L & W) all information we have on this equipment is that it is not obsolete yet any attempt to obtain a technical manual to repair this item has lead to several dead ends and we request information on ordering the proper manuals or if possible to receive an electronic copy of the proper technical manuals to repair said gear.AppreciativelyLcpl of marines

➡️ Reply Institut Dr. Forster

📝 Dmitry said:

Hi everybody.I want to buy used Ferex 4.021 and 4.032.Who can help me?Regards,Dmitry

➡️ Reply Institut Dr. Forster

📝 Pawel Poborca said:

HelloPlease send me the manual for ferex 4.021.I bought this equipment in Poland and I have no instructions.

➡️ Reply Institut Dr. Forster

📝 Roberto Perez said:

Hi: I am looking for a company that: First , I can send my IRD DATA LINe to be repair.Second: I need a new set of cables for IRd Fast trackThird: I need a chip for IRD Fast track DC_DC_ converter (dip371515db)part # IRD 35109.Do you service this equipmnet (data line) and do you sell chip and cables?Can you help me with these? If you do how do handle this, you need credit card, check, etc.Please let me know if you can help me. You can e-mail me or call at the above phone.Thank you very much for any help you can give me!Roberto Perez.

➡️ Reply Ird Mechanalysis

📝 NARONG SIRIWATTANAWONG-SAKUL said:

We have this part for IRD FAST TRACK

➡️ Reply Ird Mechanalysis

📝 John Richards said:

I have a vizio tv with a broken cable conecting the screen to the video buffer board, this cable has a chip on it .the chip is good . can you repair it?

➡️ Reply Ird Mechanalysis

📝 CHEAH CS said:

DEAR SIR,I HAVE A SET OF DEFECTOMETER MODEL H2.835 . WHEN I SENT IT OUT FOR CALIBRATION, THE VENDOR CLAIMED THAT THIS UNIT IS DECLARED NON REPAIRABLE DUE TO PARTS BEING OBSOLETE AND NOT SUPPORTED NOW. KINDLY ADVISE ON THE PART SUPPORT THE SOONEST. THANK YOUREGARDSCHEAH CS

➡️ Reply Institut Dr. Forster

📝 Estima said:

We have the equipment Forter Defectometer H.2.835, and we need it calibrated, so is it possible or is non-calibrated equipment, because it still working and we are in doubt if is self calibrated or it need to be calibrated

➡️ Reply Institut Dr. Forster

📝 Dries van Coller said:

Dear Sir, I am on contract in Kosovo but originates from South Africa. I want to perform a crack-detection inspection on a tail-rotor blade of a helicopter and have a Forster-Defectometer H2.835 at hand. I kindly request your assistance in forwarding me information how to operate this equipment to get myself aquainted with the use of it for future work.Please advice.Kind regards.

➡️ Reply Institut Dr. Forster

📝 R.K.ARORA said:

We have to carry out one inspection with H 2-835 instrument. Please confirm H 2-837 is compatible. Send details & quote for it immediately.

➡️ Reply Institut Dr. Forster

📝 R.K.ARORA said:

We have to carry out one inspection with H 2-835 instrument. Please confirm H 2-837 is compatible. Send details & quote for it immediately.

➡️ Reply Institut Dr. Forster

📝 Locklear said:

Looking for a Prom Board ASM IRD Part # 24144 fro the above Monitor

➡️ Reply Ird Mechanalysis

📝 JAYARAJAN.C.N said:

Hello, We are using the above model for three 130MW units in Moolamattom. Now we are suspecting some problems in some channels. We hope you will send your offer via my email.Regards,Jayarajan.C.N,Exceucutive Engineer,Generation Circle,KeralaState Electricity Board,Moolamattom -685589,Kerala, India.

➡️ Reply Ird Mechanalysis

📝 Saul Bonilla said:

HelloWe are using the Model 5806 and only work a channel ( channel one)We Hope your offer .RegardsSaul BonillaEnee, HondurasPhone 26605706

➡️ Reply Ird Mechanalysis

📝 Saul Bonilla said:

HolaNecesito la reparacion de un monitor model 5806 de IRD MECHANALYSIS, no aparece nda en displey , no funciona nada.Ing. Saul BonillaENEE, Honduras.

➡️ Reply Ird Mechanalysis

📝 paul J. Guay said:

Units digitol output stuck on 00 does not scan

➡️ Reply Ird Mechanalysis

📝 Dennis Dixon said:

Please advise if you can supply 2 only rebuilt or repaired IRD model 5806 vibration monitorAwaiting your reply Thanks, Dennis

➡️ Reply Ird Mechanalysis

📝 saul bonilla said:

helloI have a ird 5806 it need repair.you can it ?

➡️ Reply Ird Mechanalysis

📝 MIKE HILL said:

THE CANNON PLUG SHELL ON THE MOTOR IS BROKEN. IT IS FOR THE FEEDBACK PLUG.MOTOR MODEL IS G42PI-B41-0700-V. CAN I GET JUST THE SHELL FROM YOU OR DO I NEED TO SEND IN THE WHOLE MOTOR FOR REPAIR

➡️ Reply Industrial Devices

📝 MUSA said:

1 3EA, VALVE BYTTERFLY 12 CAST IRON BODY; SS316 DISK; WAFER TYPE; EPDM SEAT; 10 POST. LEVER OPERATION; 250PSI; SERIES : 8000WC-8271-32 2EA, VALVE BYTTERFLY 12 CAST IRON BODY; ALUMINIUM BRONZE DISK; WAFER TYPE; EPDM SEAT; POST. LEVER OPERATION; 250 PSI; SERIES : 8000WC-8281-3MANUFACTURE : ITT GRINNELLNOTE : PLEASE QUOTE C/W SPECIFICATION OR CATALOG

➡️ Reply Itt-Grinnell

📝 al leising said:

would like to get a wirin diagram on a Ice-O-Matic C400Serial # 881222212thanksAl

➡️ Reply Ice-O-Matic

📝 venkatramanan said:

SIR,WE HAVE A WEISS MAKE KNITTED FABRIC COMPACTING MACHINE IN OUR FACTORY.THE ELOP board is not functioning.the make is INAG electronics, heimsheim , germany.we need to repair the board, or have a new one.please reply immediately

➡️ Reply Inag Electronic

📝 Scott Tewell said:

I have a z board that needs repaired. This has a micro-controller on it. Have you done these in the past?

➡️ Reply Inductotherm

📝 Devin Villacruz said:

Hi, I would like to ask if the Z board can be calibrated? Reasons: 1. Out of tune. 2. Cannot attain full power. 3. Cannot attain 1200hz frequency. 3. ACR over-voltage tripped.Current condition: 1. Power can reach up tp 400kw only. 2. Frequency up to 1000hz only. 3. Turn on time too long (10secs). 4. Initial voltage upon inverter on is 500V (too high).Induction furnace model: VIP powertrak 500 R series.Company: Negros Metal Corp. Murcia road, Alijis, Bacolod City Negros Occidental 6100 Philippines

➡️ Reply Inductotherm

📝 Dennis Bress said:

Hi do you offer repair on Intel PMIX3860201F04 boardsIncluding1 x MIX 4501 x MIX 420Thank you. Best Regards,Dennis Bress 714-878-1276 IEEI and IEEI.TV, 110 Agate Avenue - Newport Beach - CA - 92662 - USATele: 949-673-2943 Cell: 714-878-1276 Fax: 949-673-0249 Email dennis@ieei.comWeb sites: www.ieei.tv and www.ieei.com Please dont print this email unless you really need to...

➡️ Reply Intel

📝 Andrew said:

Do you or can you repair an IDC (US Traffic Corp) 913A Loop Detector

➡️ Reply Idc

📝 Rene Garza said:

I looking for a operation and maintenance manuals of a ITT barton cat. No. EHR 208A1001A may you help me, pleaseB.R.Rene Garzainseel_rgarza@hotmail.com

➡️ Reply Itt-Barton

📝 FERNANDO said:

HI, MY NAME IS FERNANDO AND I AM LOCATED IN EL PASO TEXAS, I HAVE A CLIENT THAT HAS A INFRAPAK MODEL SRRITESERIAL 78125AND HE IS LOCKING FOR A WHEEL THAT GOES IN THAT MACHINE, THE INFORMATION HE GAVE ME IS: 8 OUTSIDE DIAMETER 3 WIDTH 1 SHAFT DIAMETERIF YOU CAN HELP ME, PLEASE LET ME KNOW.THANKS

➡️ Reply Infrapak

📝 Steve said:

Have an EZ wrapper model LPS looking for a replacement clutch or upgrade. I call it a clutch but its the part on the machine that you can ajust the tension of the film. I know its old didnt know if you have something thats an up grade or not. Serial # is 21992.Thanks Steve

➡️ Reply Infrapak

📝 W. Makaruk said:

Dear Sirs,I have bought an used Fast Track analyser from an ebay seller.I am looking for a on operating software for this device, more specifically, the memory of the analyser had been reseted before and i look for the programms that can be played into the analyser that are: data collection, balancing, and the software package COASTDN for the start runs.Please inform me if you could send us files that we can than played onto the device (we have the software that can do it). Please make us an offerBest Regards.W. Makaruk

➡️ Reply Ird Mechanalysis

📝 Benjamin Villegas said:

Hi, i have the files to load the os to the fast track, any version and the balancing and cost down program. my mail is cbdservicio@hotmail.com contact to me.

➡️ Reply Ird Mechanalysis

📝 James M Gradick said:

I need Cleaning/Calibration/Certification (ISO NIST) Tracible, for my IRD Fast Track Data Collectors. OS Download and Balancing/Coast Down program. Is that something you do?

➡️ Reply Ird Mechanalysis

📝 miguel bustillos calvo said:

recently acquire an ird balancing system model fast track, machine/instrument serial # 9311552, it was provide with your respective computer software.it was installed in my computer but when it runs appears the next messageird mechanalysis data analysis sistemwelcome to the ird7090 v.2.03oct 1989north america english versionand appears the next error...FCB NO DISPONIBLEanular, error ?end of file found unexpectedlycalled from C:IRD0DEV.PRGline number 00106END RUN DBRUNplease i need your help in order to correct this error and to make use of this software...i wait for your reply...thanks...miguel bustillos c.

➡️ Reply Ird Mechanalysis

📝 William Durham said:

I would like to get a copy of the manual for the Infra Pak EZ Duz It pallet shrink wrapper. I am currently experiencing problems with the turntable. The unit does not turn easily once a pallet of product is placed on it.

➡️ Reply Infra Pak

📝 Jason Enstad said:

The Shrink Wrapper that we use (listed above) @ our facility has been virtually trouble-free until yesterday (2/13/12). The carriage would not move up/or down; But the turntable would still rotate. Found out that the carriage was cocked-straightened it out. That now works but only in manual mode. Any help would be greatly appreciated.

➡️ Reply Infra Pak

📝 STEVE HYATT said:

I have a Infra pak 5000 Sidewinder. The turntable does not turn. I have power to the motor but nothing moves, Where can I get a operations manual or a pdf of the parts list?Thank you

➡️ Reply Infra Pak

📝 AMIR TAI said:

We have infra pak side winder cartridge is not going up.Thanks

➡️ Reply Infra Pak

📝 David Kinswa said:

Our Sidewinder 4 does not run the wrap up and down in auto mode. It does operate in manual mode.

➡️ Reply Infra Pak

📝 Mark Jones said:

I am looking for an illustrated parts manual for this machine

➡️ Reply Infra Pak

📝 Mike Taylor said:

I would like to get a copy of the manual for the Infra Pak EZ Duz It pallet shrink wrapper.

➡️ Reply Infra Pak

📝 James Bruns said:

looking for a copy of the manual and information for sidewinder 4. serial #F063L95H

➡️ Reply Infra Pak

📝 john Voorhis said:

We have an Infra Pak Sidewinder 4000. the release button will not work.It is also flashing numbers 1 3 and 1 7.

➡️ Reply Infra Pak

📝 RJ GARCIA said:

Good afternoon out carriage wont return to home position. It stays @ the top and wont come down. Can you send a manual for Serial# F41H94H

➡️ Reply Infra Pak

📝 LIDIA LOPEZ said:

SECOND REQUETSPLEASE QUOTE FOR MIAMIDIFFERENTIAL PRESSURE RECORDER MODEL 200 & PARTS FOR ITT BARTON11 EA LINK ASSY. ITEM-48 P/N 02380015B FAB: BARTODIFFERENTIAL PRESSURE RECORDER MODEL 202 & PARTS FOR ITT BARTON7 EA DIFF. PRESS BARTON 202 REC3PEN104KW 2500PSIW100I P-2000XP-1000CD 244/7D P/N 111-4-7FJX FAB: BARTO3 EA ARM STATIC SHAF- PEN DRIVE4 EA CLIP COVER GLASS P/N 11A2380017C FAB: BARTO11 EA SCREW ELEMENT MOUNTING (NEW P/N: 0111-0085-J)RECORDER RECEIVER, PRESSURE, ITT. BARTON MODEL 242A, S/N 242A-30140, AND PARTS13 EA RECORDER PRESSURE MOD. 242 E 2 ELEMT.N1 RGE. 0-300PSI. N2 0-5000 CDR. 24H. 7DYS9 EA ELEMENT HELICAL RANGE 0-5000 PSI MAT. 316 SST HECO 16-5000 PSI P/N 0044-0054-T30 BX CHART 12IN. CIRC. RANGE 0-5000 PSI AS SUPPLIED W./S/N 242A-30140 (MW-MP 5000) FAB: BARTO41 EA DRIVE CHART AS USED W/BARTON PRESS. RECORD RECEIVER S/N 242A-30140 FAB: BARTORECORDING INDICATING FLOW, MOD. 338E, S/N: 338380-471, D.P. RANGE 0-100, !TT-BARTON AND PARTS4 EA CALIBRATION KIT P/N 0202-1002-B FAB: BARTONMENTION DELIVERY AND WEIGHT APROX.REGARDS,LIDIA LOPEZAZULPACIFICO CIA. LTDA.QUITO – ECUADORFAX (593 2) 2534294PHONE: (593 2) 2534294

➡️ Reply Itt-Barton

📝 Nadeem Mohammad said:

I will be thankful if you please send budgetary quote for the following items. ITT Barton complete three pin recorders 02 Nos required for gas measurement at our separators. The specifications are mentioned below. Specifications MP Separator LP Separator Serial No 202N -123 202 N Static range 0 1000 psig 0 1000 psig Diff. Range 0 100 WC 0 200 WC Temp. Range 0 300 deg F 0 300 deg F Bellows material 316 SS 316 SS Kindly provide separate quote for each.My company details are as under:Company: Pakistan Petroleum LimitedAddress: Adhi LPG/ NGL plant, Tehsil: Gujar Khan, District: Rawalpindi . Punjab . PakistanPhone #: 92-51-3590150Fax # 92-51-3590322Regards, Mohammad NadeemE-mail: n_muhammad@ppl.com.pkm_nadeem120@yahoo.com

➡️ Reply Itt-Barton

📝 RASIM MAMEDOV said:

Can you please quot me Dial pressure Gauges BOURDON TYPE -CASE IP 55 WITH SCRATCH PROOF GLASS-LOCAL MOUNTING- THREADED CONNECTION ANSI B2.1 NPT-material AISI 304 CASE - AISI 316 SENSING ELEMEENT-AISI 304 MECHANISMSUPPLIED WITH RADIAL CONNECTIONMATERIAL CODE 480000142quantity 10

➡️ Reply Itt-Barton

📝 David Jara said:

Greetings ITT BARTO represent:Please can you help us with a quote of the following items?1) CLIP COVER GLASS PN: 11A2380017C, ITT BARTON.QUANTITY: 4 EA2) CIRCULAR CHART 12 INCHES, RANGE: 0-5000 PSI AS SUPPLIED W. S/N 242A-30140 (MW-MP 5000) QUANTITY: 30 BX3) DRIVE CHART AS USED W/BARTON PRESS. RECORD RECEIVER S/N: 242A-30140QUANTITY: 41 EA.Thank you for your help.Best Regards:David Jara.ELSYSTEC S. A.Quito EcuadorSouth America.

➡️ Reply Itt-Barton

📝 Donald Clemons said:

I have a Uni-Sonic Instruments System, Model EC 200-1 and T200-1-1-EP-N Serial No. 1841 (Date in service June 15, 1977). Broadcast frequency is 218 kHz. The vendor manual I have for this hardware is dated 1973.This application measures level of product and the voltage is inverted with zero reference point 14 ft from the mounting flange. The output signal is 0-5 VDC over 0-14 ft. My Operators report that the level alarms for this unit are actuating early, causing level of product in the vessel to be less than expected. Ive found very little other information onsite about operation of this equipment. Are you familar with this admittedly antiquated hardware, and if so, is it parts supported? Finally, Please advise

➡️ Reply Inventron

📝 arthur merkl said:

all equipment ever manufactured by Inventron can be repaired at the factory.734-513-7700Arthur W. Merkl,General Manager

➡️ Reply Inventron

📝 Heinrich Goeda said:

Good day I have a Telind model 56000.Can you please help me in finding this product from a supplier.Do you have suppliers in South ASfrica.

➡️ Reply Industrial Devices

📝 Mohamed Sagir said:

Dear Sir,Please quote your best price & delivery for the following item by C&F Abu Dhabi.01. Push Button Switch. Model: ABN-9111R For DLB 1000 Main Switch Board. Manuf: IDEC IAUMI CORP.Note: Freight Charge Required With OfferRgdsMohamed SagirThe Royal Industrial Tools EstPost Box No: 71930Electra StreetAbu DhabiU.A.E.Tel: 00971 2 6789786Fax:00971 2 6781105E-Mail: royaltol@eim.ae : royltool@eim.ae

➡️ Reply Idec Izumi Corp.

📝 HASSAN DAWAKI said:

PLEAS SEND US YOUR PRICE FOR 2 OF IDEC POWER SUPPLY TYPE PSR-S15INPUT AC170-264VOUTPUT DC 24V , 0-6A MFR IDEC IZUMI CORP.

➡️ Reply Idec Izumi Corp.

📝 vincent said:

Hello, I am a technician in a cheese manufacturing plant here in central valley California. I am looking for copies of the Imaje s8 Master user manual and/or machine wiring diagrams. If you would be willing to make one available, or know of a resource to obtain , it would be of great help. Vincent

➡️ Reply Imaje

📝 rick gatchell said:

looking for spares for this unit or direct replacements

➡️ Reply Ird Mechanalysis

📝 Brian Greenawalt said:

Can you get parts for a 1823-0025 Inertia Dynamics brake? It is a brake made special for Parker. It appears to be close to a SAB 400 brake. I need a new splined rotor.

➡️ Reply Inertia Dynamics

📝 mitch said:

i need to reline no. 1905 2721. thanks mitch

➡️ Reply Inertia Dynamics

📝 dave parr said:

I would like a schematic drawing. We had a power surge during an ice storm. It damaged two resistors beyond the point of recognition. I cant read the color bands. So i dont know the value of the resistor.If you can help I appreciate it. If not okay.Please reply either way.Thank you, Dave.@ Bayer Appliance & Hardware.

➡️ Reply International

📝 ketan. raval said:

i have an amplifier modelno.IM-LDT42 S/N : 010902 C 000095 the fault is its DSP is not properly working. plz give me kind advise as soon as well.

➡️ Reply Industrial Devices

📝 Carlos Dominguez said:

1. How do I adjust the contrast on the Fast Track screen.2. We have Emonitor Odyssey. I could load the Fast Track Operating System, but how do I load the balancing program and the Startup-Coastdown programs.

➡️ Reply Ird Mechanalysis

📝 Sasha Romano said:

1Barton Link Assy P/N 0238.0015BEA122Barton Arm Assy P/N 0238.0031BEA123Dual Pen Mount Assy P/N 0238.0014B - BartonEA124Pen Arm Shaft P/N 0238.0006B – BartonEA125Pen Arm Shaft P/N 0238.0007B – BartonEA1260-2000 PSI Static Pressure Elements - BartonEA127Red Pen with .140 in nibEA248Red Pen with .301 in nibEA249Red Pen with .750 in nibEA2410Blue Pen with .130 in nibEA2411Blue Pen with .320 in nibEA2412Blue Pen with .600 in nibEA24

➡️ Reply Itt-Barton

📝 JERRY DORMINEY NORTH GEORGIA MACHINERY said:

HAVE AN ICS A4830 VIDEO OR GRAPHICS CARD THAT NEEDS CHECKED OUT AND MAYBE REPAIRED OR REPLACED.

➡️ Reply Ics

📝 GHANBARIAN said:

HELLO I WANT MANUAL FOR ANALOG CARD AIO120 12B CAN YOU HELP ME .WE HAVE THIS CARD ON THE MACHIN BUT Defective .BEST REGARD

➡️ Reply Ics

📝 Matthew Ritter said:

I am trying to find someone to help me repair a LCP-3A made by Inverpower. This unit is in an industrial setting namely in a Steel Mill. The entire unit seems to be working fine except for the LCP-3A. This board causes the unit to trip if it goes over 900 revolutions a minute. The normal operating speed in 1100. If someone could help me with this it would be great. Maybe ideas for parts or anything.ThanksMatt Ritter

➡️ Reply Inverpower Controls

📝 kirimi justus said:

I own a diploma in mechanical engineering plant option and would be happy to work with you to meet your set goals. thank you.

➡️ Reply I.P.E.-Cheston

📝 Michael Farina said:

Hey, the ICOS 00366803 CONTROLLER went down mid-shift. Need someone to check it out ASAP during the day to get it back up and running. Thanks!

➡️ Reply ICOS

📝 girish vyas said:

dear sirwe need to have spare part / parts list for the various machines we are using as defectomat CP/CI and ECMRegardsGirish Vyas

➡️ Reply Institut Dr. Forster

📝 Charles Sprague said:

We have an older infrapak 4000 shrink wrap machine. The small circut board that turns the current from A/C to D/C has burned out and we are unable to find another one. Do you have any suggestions?

➡️ Reply Infrapak

📝 Dr. Hira Shah said:

Dear SirWe have ICG machine : Patient Box , Hemosapiens we need cords 1) Tebco oemrs 32 with USB port 2 pieces and Tebco oem/ead 4 pieces If you can make it available to us the above cords kindly email Best regardsDr. Hiral Shah

➡️ Reply Icg Machine

📝 Jesus Ortega said:

Having issues with the ITT Barton Assy 105493 board in our industrial unit. Not functioning properly, need repair assistance as soon as possible.

➡️ Reply Itt Barton

📝 Ndue Merturi Norwalk Transit District said:

please provide me with info on the repair or replacement of this defective unit

➡️ Reply I/O Controls Corp.

📝 eric crandall said:

i wish to get a copy of manual for sidewinder 3 serial#to52h95e looking for the parts breakdown and electrical prints for repair

➡️ Reply Infra Pak

📝 victor said:

Favor de ayudar con diagramas para este convertidor ABB VERITRON ASD6701 VERSION 6

➡️ Reply Infra Pak

📝 Dan Hurley said:

I have a IPE CHESTON Model # SP-129 KVA 154. I am looking for a point of contact for some one to come and service this machine. We had all three of the main fuses blow yesterday.

➡️ Reply I.P.E.-Cheston

📝 thiagu said:

We have an Introl Designs, Inc. 336-9 unit that is not powering on. Can you help diagnose and repair?

➡️ Reply Introl Designs Inc

📝 davinder said:

Italsea CFBR601.1 unit not powering on or responding. Need urgent repair assistance to diagnose and fix the issue.

➡️ Reply Italsea

📝 David Vendetta said:

We have a Sidewinder shrink wrapper in need of service. It possibly needs turntable bearing and pin, as well as roller bearing and shaft weldment.Please advise a local service rep or tell me who I can get in Rochester, NY that I can contact.Thank you,David VendettaFacilities ManagerC&M Forwarding585-370-6451

➡️ Reply Infrapak

📝 Matthew Kornegay said:

Hello,We have a door control module at our Greene Correctional facility that is down.We have found the Node module to be bad. This is the information on the module casing.IDEAS S/N -TrenTech: 334-286-4280Can you please help with this part?

➡️ Reply Idea

📝 Kamp said:

: Our production line has been experiencing intermittent issues with the automated packaging system. Its stopped working entirely on multiple occasions, preventing us from fulfilling orders and generating revenue. The unit, a high-speed robotic arm designed for packing fragile items into boxes, has stopped operating entirely, leaving us unable to meet our delivery deadlines. We estimate the cost of a new replacement unit would be between $50,000 - $70,000, depending on model and customization options. We need to resolve this issue as quickly as possible to minimize downtime and lost production.:

➡️ Reply Iota

📝 DAVID POTTER said:

Hi,Do you repair the above electric cylinder? If so, is there a standard repair cost for this cylinder? Thank you.

➡️ Reply Industrial Devices

📝 Christopher DeVillez said:

Need repair

➡️ Reply Infrapak