Welcome to IND

We repair a wide range of IND Equipment.

Ask questions, or 1-336-969-0110 for faster service.

Use the search bar above to find specific manufacturers.

• 40+ years of experience repairing Industrial & Commercial units
• Certified Senior Industrial Electronics Technician
• Ability to do Reverse Engineering
• No job to big or small
• Fast turn around time on most units
• Quality of work comes before profit!
• Old Fashion Customer Service is always the right policy
• Extended warranty
• Fair Estimates
• Low Prices

No repair summaries available yet for this manufacturer.

Comments for IND

📝 Sales Service said:

If you need your unit tested or repaired then give us a call.We offer fair estimates and offer extended warranties.You can contact us at 1-(336)-969-0110Shipping/ReceivingIndustrial Electronic Repair931-E S. Main St #204,Kernersville, NC 27284 Phone: (336) 969-0110We repair industrial electronic devicesIf you have an industrial electronic device that needs repair,Feel free to contact us!

➡️ Reply Industrial Electronics Repair

📝 Francisco said:

I have 2 Goring-Kerr (Thermo Fischer Scientific) DSP2 metal detectors that show the following faults in the status page: Faults: 3 Product memory - search head - RF board. I do not have the operator/supervisor/Engineer passwords and the password seed numbers are (what I assume is by default): Operator: 12345678 Supervisor:23456781 Engineer: 34567812. I have tried using password ZBZB but it does not work. Conveyor belt turns on and off and red fault light is on. Any suggestions? Thanks in advance.

➡️ Reply Industrial Electronics Repair

📝 DonaldBox said:

telegram virtual numbers

➡️ Reply Industrial Electronics Repair

📝 Lynn said:

New Feedback Report Name: Lynn Location: n/a Department: N/A Price Rating: ⭐⭐⭐⭐⭐ Service Rating: ⭐⭐⭐⭐⭐ Support Rating: ⭐⭐⭐⭐⭐ Message: Thank You for repairing our drive and fast turn around.

➡️ Reply Industrial Electronics Repair

📝 Scot said:

Inductotherm 804237 circuit board experiencing intermittent power loss, causing disruptions in industrial unit operation. Need immediate assistance for repair.

➡️ Reply Inductotherm

📝 MIKE HILL said:

THE CANNON PLUG SHELL ON THE MOTOR IS BROKEN. IT IS FOR THE FEEDBACK PLUG.MOTOR MODEL IS G42PI-B41-0700-V. CAN I GET JUST THE SHELL FROM YOU OR DO I NEED TO SEND IN THE WHOLE MOTOR FOR REPAIR

➡️ Reply Industrial Devices

📝 Scott Tewell said:

I have a z board that needs repaired. This has a micro-controller on it. Have you done these in the past?

➡️ Reply Inductotherm

📝 Devin Villacruz said:

Hi, I would like to ask if the Z board can be calibrated? Reasons: 1. Out of tune. 2. Cannot attain full power. 3. Cannot attain 1200hz frequency. 3. ACR over-voltage tripped.Current condition: 1. Power can reach up tp 400kw only. 2. Frequency up to 1000hz only. 3. Turn on time too long (10secs). 4. Initial voltage upon inverter on is 500V (too high).Induction furnace model: VIP powertrak 500 R series.Company: Negros Metal Corp. Murcia road, Alijis, Bacolod City Negros Occidental 6100 Philippines

➡️ Reply Inductotherm

📝 Heinrich Goeda said:

Good day I have a Telind model 56000.Can you please help me in finding this product from a supplier.Do you have suppliers in South ASfrica.

➡️ Reply Industrial Devices

📝 ketan. raval said:

i have an amplifier modelno.IM-LDT42 S/N : 010902 C 000095 the fault is its DSP is not properly working. plz give me kind advise as soon as well.

➡️ Reply Industrial Devices

📝 Ribeiro said:

Subject Inquiry Regarding Support for Indramat TDM1.3-100-300-W1 Servo DriveDear ,I am reaching out on behalf of our team regarding an Indramat TDM1.3-100-300-W1 Servo Drive that we are in need of repairing or replacing. The equipment is older, and unfortunately, we are unsure of the manufacturer. Could you please provide information on whether the Indramat TDM1.3-100-300-W1 Servo Drive is still supported by your company? Additionally, we are interested in knowing if replacement parts are still available for this unit.Any assistance you can provide in guiding us to the right repair or replacement options would be greatly appreciated.Thank you for your attention to this matter.Sincerely,

➡️ Reply Indramat

📝 Mike Olszewski said:

Subject Indramat Servo Drive IssueHi there, I wanted to let you know that the Indramat KDS1.3-100-300-W1/S104 servo drive is not working as reported. Assistance is needed in resolving this issue

➡️ Reply Indramat

📝 DAVID POTTER said:

Hi,Do you repair the above electric cylinder? If so, is there a standard repair cost for this cylinder? Thank you.

➡️ Reply Industrial Devices