We repair a wide range of L-Tec Equipment.
Ask questions, or call 1-336-969-0110 for faster service.
Use the search bar above to find specific manufacturers.
The L-TEC 674972 REV-A PCB is a printed circuit board used in industrial electronics, typically found in control panels or power supplies. It serves as an interface between various components, facilitating communication and control within the system. Its features include multiple input and output connections, integrated processing capabilities, and possibly built-in diagnostic functions. Common failures in the L-TEC 674972 REV-A PCB may include cracked or damaged traces, defective components such as capacitors or resistors, and faulty solder joints. These failures can lead to system malfunctions, communication errors, or complete failure of the device. Regular inspection and maintenance can help prevent such issues and ensure proper functioning of the PCB.
The L-Tec WM-637C circuit board is utilized in industrial electronic systems for controlling various functions such as motor drives, sensors, and communication interfaces. This circuit board offers features like high reliability, precise control, and robust construction. Typical failures can include blown fuses, damaged components, or malfunctioning connectors, which can be diagnosed and repaired by experienced technicians through troubleshooting and component replacement procedures.
The L-TEC 674956 PCB is a printed circuit board used in industrial electronics. Its purpose is to regulate and control the functions of a specific electronic device. This PCB is known for its high reliability and durability. However, common failures include component burnout, solder joint issues, and electrical short circuits. It is essential to troubleshoot and repair such failures to maintain optimal performance of the electronic device.
The Plasma Cutter L-Tec PCM-VP1 is designed for industrial metal cutting applications through the process of ionizing gas to create a high-temperature plasma arc. It features precise control over the cutting current, gas flow, and torch height to ensure clean and accurate cuts. Common failures in this unit include issues with the power supply, control circuitry, and torch components such as the electrode or nozzle. Regular maintenance, such as cleaning the torch and ensuring proper gas flow, can help prevent these failures.
The plasma cutter L-Tec 680536-PCM-32i is designed for industrial metal cutting applications. It utilizes a high-temperature plasma arc to cut through various conductive materials with precision. Features of this model may include adjustable cutting parameters, digital control interface, and reliable cutting performance. Typical failures in this plasma cutter can include issues with the power supply, control board, or plasma torch components, leading to decreased cutting efficiency or complete system failure. Routine maintenance and timely repairs are essential to ensure optimal performance and prolong the lifespan of the unit.
The L-Tec PCM-7501 is a plasma cutter that is designed for industrial applications. It is used to cut various materials such as metal, aluminum, and stainless steel. The unit features a high-frequency pilot arc system for easy starting and a constant current output for steady cutting performance. Typical failures in the L-Tec PCM-7501 plasma cutter can include issues with the power supply, control board malfunctions, or problems with the cutting torch. These failures can often be diagnosed through testing the input and output signals with a multimeter, checking for loose connections, and inspecting the internal components for signs of damage.
The L-Tec WM-637C Circuit Board is designed for industrial applications. Its main purpose is to control various processes within a system. It features a compact design, high-quality components, and reliable performance. Typical failures can include burnt-out components, solder joint issues, or communication interface failures. Regular maintenance and troubleshooting procedures can help ensure the longevity and proper functioning of the L-Tec WM-637C Circuit Board.
The L-Tec PCM-32i 680536 is a welding and cutting system utilized in industrial applications. It is designed to provide precise control over welding parameters such as voltage, current, and pulse frequency. The system features digital controls for ease of operation and a robust build quality to ensure reliability in harsh working conditions. Common failures include issues with power supply components, control system malfunctions, and faulty communication interfaces. Regular maintenance and monitoring of the system's components are essential to prevent unexpected downtime and ensure optimal performance.
The L-TEC PCM-VPi 31746 welder is a powerful industrial electronic device used for welding applications in various industrial settings. This model is known for its high precision and reliable performance. It features advanced control systems for regulating welding parameters such as current, voltage, and pulse frequency. Typical failures in this welder may include issues with the power supply, control board malfunctions, and failure of internal components such as capacitors or transformers. Proper maintenance and regular inspection are recommended to ensure optimal performance and prolong the lifespan of this welder.
The L-Tec PCMVPI Plasma Cutter is an industrial electronic device used for cutting metal sheets and materials. It utilizes a high-frequency electric arc and compressed air to cut through conductive metals with precision. The device features adjustable cutting parameters, such as current intensity and gas flow, to tailor the cutting process to specific material types and thicknesses. Common failures in plasma cutters like the L-Tec PCMVPI include issues with the power supply unit, such as blown fuses or faulty capacitors. Additionally, problems with the cutting torch, such as damaged electrodes or clogged nozzles, can lead to improper cutting performance. Regular maintenance, including cleaning and inspecting the torch consumables, is essential to ensure the longevity and proper functioning of the plasma cutter.
Board is an Esab componet that operates an Esab PCM 750-iplasma cutter. Esab (L-tec) Part # 838008 Rev. C.➡️ Reply L-Tec
I have the subject plasma cutter and am trying to use it in a X-Y machine operated by my older computer. It works most of the time but it seems the high frequency start is killing the computer on occasion. Is there a way to disable the hi frequency start circuit ?Thank you Bill➡️ Reply L-Tec
My L-Tec Plasma cutter PCM VPI has a short in the circuit board, i can bend it up and it start working fine but I cans fine the open circuit or lose wire, Could I sent only the board for repair or is this thing worth repairing, Thanks, Clyde➡️ Reply L-Tec
tendran informacion de diagrama de tarjeta de plasma pcm-750i, numero de parte (8) 38008 ya que lo requiero.porque la estoy reparando favor de mandarme contestacion➡️ Reply L-Tec
I have an L-Tec Plasma Cutter with a capacity of 1-1/2 thick steel, 230V. It powers OK but the tourch not working. Please do you carry any.➡️ Reply L-Tec
Hi, I have a L-TEC brand plasma cutter pcm-7501, p/n 32905, serial a93b41632 and was wondering if I could ask you a question or three about it?My questions are,it will power up fine, and when you select air test, that function works as well. There is no fault light on, but the problem is that the unit will not do a thing when you push the trigger. We have tried changing the tip consumables out with new parts, and checked the trigger also. It tested fine. Is there anything that I could do or test before I bring it in to get it tested? Is there a common problem with these machines that maby i could fix? and lastly, If the circuit board is bad, how much for one and is it even worth fixing this machine.Sorry for the long post and thank you for your help!Ken➡️ Reply L-Tec
The problem is probably in the trigger or broken wiring back through the leads. If you have any of the electrical drawings, they should show where to close the connection inside the power supply to fire the torch. If it fires that way your problem is in the leads or trigger.➡️ Reply L-Tec
I NEED A SHAPE BOARD FOR MY L-TEC UCNC -8 PLASMA 810 OR A WAY TO HOOK UP A PC I HAVE MODEM BUT THE CABLES WANT GO TO MY XP USB AND A PROGRAM TO RUN IT . THANKS TEWLL RUDY IT STILL NOT WORKING➡️ Reply L-Tec
I have a L-TEC PCM UP1 plasma. Serial#a93a 34529.When I turn it in the fan comes on but nothing else will work. Help➡️ Reply L-Tec
I cannot get to work. I do not get anything on screen. This equipment was purchased in 1980 for cnc plasma cutting system for ductwork. I messed up origional software few years back. thanksballi➡️ Reply L-Tec
i need parts for my machine hopfuly u can help me thx kent jarrell➡️ Reply L-Tec
I have an L-Tec PCM750i plasma cutter, the power is on, air going through, the fault light on, fuse is good, arcs at the gun but will not cut.➡️ Reply L-Tec
The power turns on, air is going through, the fault light is on, fuse is good, arcs at the gun but will not cut. I have already stuck $1,300.00 into this machine in repairs.➡️ Reply L-Tec
i need manual for this Plasma Machine , Model:- PCM-100Plasma Arc,L-TecHope to receive the same.➡️ Reply L-Tec
my overload light is on everything esle seems to be working what do you think it is and or what can i try➡️ Reply L-Tec
Hi . Im looking for L-Tec Compact aircut 25 diagram for my Telwin plasmarc 250 (I know its strange but both of units are similar construction)Telwin forgot about this machine - have no diagram they sad its to old ...What is cost of one of parts that L-Tec plasma cutter -I mean HF transformer electronisches zundgerat SIG 3.2 .Its grey box made in west germany with 4 pins (marks HB HO TO T24 ) Regards Witek from Poland➡️ Reply L-Tec
Hi I can give you systems like the zundgerat PLasma ignition systems , quite reliable they work very well for plasma , and TIG we make our plasma systems , we use them in these plasma machines.proarcindia.com➡️ Reply L-Tec
Kindly tell me how to repair the L-TEC- CB7WB , Model VI502 , there is problem in the holder and also the plasma cutter holder is not available in the local market ,second the holder fot the co2 welding also not working can i purchase it form u thanks give me a call 00923339500248➡️ Reply L-Tec
Unit quit working and I would like to find out if it is worth repairing. I,m retired now and would like to use it once in a while.➡️ Reply L-Tec
This is a 220 unit that was pluged into 480 is it worth repairing .Thanks➡️ Reply L-Tec
Do you have someone in our area that works on the L-Tec machine➡️ Reply L-Tec
I have an L-TEC PCM-VPI plasma cutter. It doesnt work, I took it to Valley Welders Supply in Billings, they told me that it needs a new circuit board. What would be the cost and/or is it cheaper to buy a new plasma cutter?Kind Regards,Mike➡️ Reply L-Tec
i need 2 encodersmodel: k15dd 6a5e,0080p/n 6-111868-0080➡️ Reply L-Tec
I am looking for output diodes for the above unit. The console has a pn of 31746 and SN: a93a 31328.I spoke with Jamie @ esab. They can only come up with the doide module pn: 951902 and that part is obsolete.This unit has the individual output diodes, I believe two forward and two reverse polarity.Thanks,Pat➡️ Reply L-Tec
i have a pcm 32 i, and the light overload is open (is red) the machine ist doesnt work ,what is the trouble?➡️ Reply L-Tec
Dear Sir,We would like to introduce ourselves as registered supplier/indenter of various types of machinery/tools/Raw Material/electronics items with many of government and private sector organizations in our territory. One of our customers would like to purchase below mentioned items on urgent basis. S #ITEM DESCRIPTIONUOMQTY1MECHANIZED PLASMA ARC CUTTING TORCH WITHOUT RACK PT-20M (L-TEC, USA) 100 AMP P/NO 20593NO.1You are requested to please send us the literature along with your offer on FOB/C&F Basis for submission to the customer. You are requested to please reply through return mail. We are anxiously waiting for the reply. Thanking you in anticipation. Best regards Mobeen Ashraf Manager International Purchase Department Nazir & Sons International 2ndFloor, PrachaPlaza, Near Municipal Committee Office, Faisal Shaheed Road, Taxila, Pakistan. Ph No: 0092-51-4547995 Fax No: 0092-51-4547997 E-mail: nazirsonpvt@yahoo.com➡️ Reply L-Tec
My machine does not work and cannot use L-Tec 810 controller to to do anything.I just get black screen➡️ Reply L-Tec
I do not have existing Ductling II software. L-Tec 810 screen comes on with white dots filled and no instruction to do anything. Advise 202-438-0224➡️ Reply L-Tec
Hi I have L-Tec 7501 plasma cutter 220 single Ph was pluged into 440 is it repairable Thanks➡️ Reply L-Tec
i dont get any air➡️ Reply L-Tec
Industrial Electronic Repair
145 Rockwell Place Ct
Tobaccoville, NC 27050
🚑 Rush repair shipments only — no walk-ins.
Industrial Electronic Repair
931-E S. Main St #204
Kernersville, NC 27284
📦 Mailing Address (for invoices or shipped repairs)
No walk-ins accepted.