Welcome to ME

We repair a wide range of ME Equipment.

Ask questions, or 1-336-969-0110 for faster service.

Use the search bar above to find specific manufacturers.

• 40+ years of experience repairing Industrial & Commercial units
• Certified Senior Industrial Electronics Technician
• Ability to do Reverse Engineering
• No job to big or small
• Fast turn around time on most units
• Quality of work comes before profit!
• Old Fashion Customer Service is always the right policy
• Extended warranty
• Fair Estimates
• Low Prices

No repair summaries available yet for this manufacturer.

Comments for ME

📝 Robert Castillo said:

I have a sensor that may need to be repaired or replaced. The part # is MEK 93-RD. It is used for a shrink wrap machine. If it is possible to repair or replace, please give me a call.

➡️ Reply Mekontrol

📝 gray hartley said:

I have an need for one of these for my pallet wrap machine. HELP

➡️ Reply Mekontrol

📝 chris said:

HELLO SALES,I GLAD TO SEND YOU THIS EMAIL I WANT TO ORDER FROM YOUR STORE TO MY CLIENT, I WILL LIKE TO KNOW IF CAN SHIP TO USA,EUROPE,UK ? PRODUCT.DETAILS:Megger OTS60PB Automatic 60 kV Oil Test Set KINDLY GET BACK TO ME WITH THE TOTAL COST OF THE ORDER WITH SHIPPING CHARGES AND WHAT TYPE OF CREDIT CARD YOU ACCEPT ? GET BACK TO ME BEFORE CLOSINGTIME TODAY.Best RegardsCHRIS MIKE

➡️ Reply Megger Instruments

📝 John Davison said:

we have a metramatic weightec ser# 411782 Model # weightec LW II Which is in need of the out feed beeded chain guides parts 1432219 1 7and 1432219 7 these pieces are 3.25 long would you have these parts or could you point me in the right direction to get these parts thank-you

➡️ Reply Metramatic

📝 Jimmy Ng said:

Can you do repair METRONIX Servo Controller Model: ARS 310/5.Please quote also.RegardsJimmy Ng

➡️ Reply Metronix

📝 don coury said:

Have a couple questions in changing from a four line system to a two line system. I have pictures but theres no way of sending cant find your email. If there is any way I could talk to someone familiar with this unit Id appreciate it. Sincerely, Don Coury

➡️ Reply Metramatic

📝 Mark Howell said:

I have a Melco Emt 10-4T and apparently had a power surge. It seems to have burned up some boards, at least some components. I replaced the power supply because I could see one component fried. Still cant get the machine to work. It will display e-stop engaged. I have disconnected the emergency stop buttons but it still doesnt work.

➡️ Reply Melco

📝 vicki palonen said:

i have a emt 10t phase 2 it just died i feel it must be the power supply no lights nothing do u repair power supplys i checked with melco and they will replace it new for 1200 or rebuilt for a 1000 i would love to have other options its a great machine i bought it new in 98 i really need to get it working again this is my lively hood thanks vicki

➡️ Reply Melco

📝 roger koren said:

the screen shows nothing when i start up the machine. it is blank.

➡️ Reply Melco

📝 roger koren said:

the screen shows nothing when i start up the machine. it is blank. it is not a monitor. it the screen where you insert the 3 1/2 floppys.

➡️ Reply Melco

📝 JACK CROWLEY said:

CAN THEY BE REPAIRED OR ANY AVIALABLE. THANKS

➡️ Reply Melco

📝 Curt said:

Do you have experience repairing these units? Do you have set pricing for repairs, or is it Time and Materials per job? Do you have a way to test them when completed to be sure they work?

➡️ Reply Metcal, Inc

📝 manoj badapanda said:

Hi team, the Meidensha Corporation VT110 H 35B, 5.5A Inverter unit is not functioning properly. Please investigate the issue further. Thank you.

➡️ Reply Meidensha Corporation

📝 JACK L FEAK said:

We have a Melco EMT 10/4T machine with a start-up boot problem. I believe there may be a electronics hardware problem (memory error?). Error is BOOT DISK ERROR_. After replacing the floppy disk drive and new boot floppy disk a closer examination indicates a problem in the self test routine (I think). The system used to go through the self tests and then looks for the floppy but now stops after the RSA Memory Test PASSED, and immediately displays B4 and stays there until enter is pushed again.Do you have any idea where to start troubleshooting? I have an electronics degree so you can talk as technical as you wish. We were hoping to diagnose the problem and send you only the defective part for repair. (my guess is dynamic ram error bank 4 on CPU board but just a guess). See the following boot display sequences. Any Help would be greatly appreciated!System stack PASSEDRSA Memory PASSED (then jumps immediately to B4 and stays until Enter is pushed)Bunch of corrupt characters now displayed (stays on that screen until Enter is pushed)Lan Card Locate PASSEDLAN EEPROM LOAD PASSEDSelf-test PASSEDEBIOS V1.04 928KINSERT BOOT DISK_BOOT DISK ERRORmachine infoMelco EMT 10/4T Model 01050002Serial # 790799Mfg date 01/2000

➡️ Reply Melco

📝 Muhammad Amjad said:

URGENT REPAIR NEEDEDIssue META VISIONS SYSTEMS LTD E811-01 LASER PARTICLE COUNTER malfunctioning. Unable to accurately detect particles, affecting quality control on production line. Immediate attention required to avoid production delays.

➡️ Reply Meta Visions Systems Ltd

📝 Vivian curtis said:

: I am experiencing issues with my Metrix PMC/Beta vibration monitor model GM3221-0102-278. The unit isnt detecting vibrations as it should and I need to have it repaired or replaced. Can you please provide me with an estimated cost for a replacement unit or repair of this model?:

➡️ Reply Metrix Pmcbeta