Welcome to PA

We repair a wide range of PA Equipment.

Ask questions, or 1-336-969-0110 for faster service.

Use the search bar above to find specific manufacturers.

• 40+ years of experience repairing Industrial & Commercial units
• Certified Senior Industrial Electronics Technician
• Ability to do Reverse Engineering
• No job to big or small
• Fast turn around time on most units
• Quality of work comes before profit!
• Old Fashion Customer Service is always the right policy
• Extended warranty
• Fair Estimates
• Low Prices

🛠️ Common AI Repair Summaries 🏭

Comments for PA

📝 JIM KITSON said:

I HAVE A PAVID GEN SET MODEL J13GAW-HNEED WIRING DIAG. TO CHANGE FROM 480V 3 PHASE TO 240V 3 PHASETHANKSJIM KITSON

➡️ Reply Pavid

📝 Joe K said:

I dont know if you found the information on re-straping your generator or not but if you still need a print, e-mail me and Ill send you what you need.

➡️ Reply Pavid

📝 R C Engines said:

We have a C18H3 M-G set and we are looking for a wiring diag. Can we purchase a copy of the diag. from your company? We are having problems with the output voltage. Please email us if you can be of asst. Thank You

➡️ Reply Pavid

📝 Faith Epp said:

I have a pavid 45 kw generator head, (no engine yet) . It is a 12 wire set that I am told can be wired for 1,2,and 3 phase. It is presently wired 3 phase, parallel Y, 4 wire. Can someone tell me the wiring format for 120/240 single phase, 3 wire? my wires are marked T1-T12.I am aware that I may need to rewire some of the meters but Ill deal with that later. Right now I just need to know where the T wires go. thanks

➡️ Reply Pavid

📝 STACY REED said:

Hello,I was wondering if you can provide me a manual for the Teledyne Pines machine?thank you

➡️ Reply Pavid

📝 martha\'s Design Center said:

Out-put wiring information. Using Generator for back-up power for manufacturing business. Power 3 phase...

➡️ Reply Pavid

📝 Stan said:

We are looking for a starter motor for a model G18H3 Pavid generator. The serial number is 2227.

➡️ Reply Pavid

📝 Jeff Slayton said:

I have an engineer interested in learning more about an old Pravid generator system - where were they made? are parts still available?

➡️ Reply Pavid

📝 Mike Fu said:

Dear Madam/Sir,Can you repair the old Parvex servo driver? The Model number is SD/CC 200/20/40, Nr# 19.964This driver is over 20years old, and installed and used for driving spindle for Prosys Bobbin winder.If your company doesnt do such a service, could you please let me know which company does such a service?Thank you,Regards,Mike FuElectrical EngineerSiemens VDO Automotive Inc.700 Park. Ave. EastChatham, OntarioCanada, N7M 5M7Phone: 1-519-436-3684Email: mike.fu@siemens.com

➡️ Reply Parvex

📝 Hans Blauw said:

Can you give me the specs or technical documentation of a old Parvex motor EC 11 T. Code ED R0501 06 80is there any replacement ???Best RegardsHans Blauw Technical engineerwww.tevel.nl

➡️ Reply Parvex

📝 SALVADOR DUARTE CERVANTES said:

Can you give me the specs or technical information of a VOAC hidraulic motor.Part. No. 3707325Type:ser.N.2000150747F11-150-HF-SH-S000

➡️ Reply Parvex

📝 John Maguire. said:

Panadac PCB Type 853K -001BPanasonic Part # N203p 853K -001

➡️ Reply Panadac

📝 Dave said:

Gentlemen:I have a 25 year old Tri-Tronics elrctronic dog training collar that does not work properly.The factory no longer services this unit and their contract repair service is unable to fix it to last more than their 90- day warrenty. This inut origibally cost $550 and every wear part (the switches) has been replaced. I think current ni-cads are junk but dont really know.Obviously no heat problem 6-12 V .I would like to consider making new single layer boards (China?) but would need schematic for same.Will you take a look at it and give me a quotation?Thanks.DaveP.S. Tried to phone...bad/no connection.

➡️ Reply Panadac

📝 Tom Goh said:

Hi Sir,If you can service and repair Panadac 550 controller, please reply me as soon as you can. I currently have a few units awaiting for service.Thank you.

➡️ Reply Panadac

📝 reyner said:

hi, i want to change the program of the panadac 783-900 but I dont have information about this(manual,source code,etc)Can you share please information

➡️ Reply Panadac

📝 EDUARDO said:

Need to driver therm printer PANADAC 931-02THANKS

➡️ Reply Panadac

📝 Paul Drudge said:

would a diagram of terminal location for multi voltage be available?

➡️ Reply Pavid

📝 clarence silvers said:

Hi, ive got an old c18h3 or g18h3 pavid generator, its hard to tell if its a c or a g from the dataplate. It had been working really well untill we went to fire it up to test it before the last ice storm when we noticed that the output was really fluctuating, now it doesnt have any output. I was wondering if you had any electrical prints or advice on things to check out on the unit. Thanks Clarence

➡️ Reply Pavid

📝 Tom Robertson said:

Dear Sirs,I have a Pavid unit on top of the Sullair genset.Model No.: 248275-001Serial No.: 6184I need some information on the functions of the controller board.Does the controller board regulate the RPM of the engine electronically. or does the unit need a solenoid or mechanical govenor.The unit is a 1995 Sullair Genset.Model No.: J75BOM No.: 6716Serial No.: 098G2167 FHOKW - 75Hz - 60Voltage - 277 /480Also, if you have information about where I can get operation and maintenance manuels, I would appreciate it.Thanks in advance,Tom

➡️ Reply Pavid

📝 Cesar Diaz said:

Hi ive got an old pavid brush less Model # G15 H3 Serial # 4290 Kw 187-15 Volts 139WDC it had been working good now it doesnt have any outp ut 120 V and 480 V I was wondering if you had any electrical prints or adavice on tings to check out the Unit thanks Cesar

➡️ Reply Pavid

📝 Ruth Turner said:

Where can my husband get information about the above referenced generator?Thank you.Ruth Turner

➡️ Reply Pavid

📝 Anthony Woods said:

I have a Pavid Model G 20 H3. The Crank Timer Board is getting a start signal from the ATS but it is not sending the signal to start the Engine. The unit will start manualy. Is their anything you could suggest. Thank you

➡️ Reply Pavid

📝 Harry said:

I need an oil pressure switch for a PAVI Generator MOD: G20H3. Yhis is a normally closed switch that starts the engine then cuts the starter off after proving oil pressure.White Diesel EngineMOD: D200SN: TH3432857SPEC:X99

➡️ Reply Pavid

📝 al suckow said:

Is there any way to test these units? I have several. how long does it take? Also I am looking for new sensors for these the pakstat part # is 01724601-001. Do you sell these or know of a vendor? Thanksal suckow

➡️ Reply Paktronics

📝 Wendy said:

This unit has a white face and says Co-Stat on the front with a knob to turn right for hotter, left for cooler.It is installed to control floor heating in our entryway. Temp control knob is always left in the same position, however suddenly it began heating this floor at maximum temp. Turning the knob did not reduce temp so we disconnected the unit.Assuming the control knob has become faulty, can this be repaired, or if not where can we buy a replacement unit?Thanks.

➡️ Reply Paktronics

📝 bilal said:

Certainly! Heres a brief message reporting the issue with the Parametrics 600363f---During my inspection of the Parametrics 600363f, I observed several issues that need attention- The unit emits a noticeable humming noise when powered on, which is not typical under normal operating conditions.- There is intermittent flickering in the display panel, suggesting a potential connectivity or power supply issue.- The unit occasionally fails to execute commands

➡️ Reply Parametrics

📝 Kristen Ames said:

To Whom it May Concern: I am current looking for a repair facility that has the capabilities to repair Pacific Scientific PN# SC752A001-01 Model# SC750 Servo . I came across the companys website and I have a couple of questions about the companys background of repairing these drives. 1. How long has the company been repairing Pacific Scientific?2. Do you have manuals, documentation on all models for Pacific Scientific?3. Can these drives be load tested?4. Do you have the software to repair these drives?5. Do the technicians have a QC Procedure?6. What is your standard turnaround for repairing these?7. What is your turnaround on expediting?8. Do you offer exchange programs?9. Do you offer pricing for new?10. What is your warranty period?11. Are there any fees for evaluation?12. Do you require an RMA to send unit in for eval/repair.13. Could you also supply me a repair price for the PN# SC752A001-01? A quick response will be greatly appreciated!! Thanks, Kristen AmesEMA of NY

➡️ Reply Pacific Scientific

📝 larry said:

need info for wiring digrams on gen and controll boxthanks

➡️ Reply Pavid

📝 larry said:

need any manuals for this gen thx

➡️ Reply Pavid

📝 Mark Hedden said:

Hi,I need the same thing. Ihave a 1976 Pavid 35KW 12 wire and I just need to know how to arrange for 240 volt/3 phase. The factory plate says its wired for 139 volt? Sounds wrong, but its the factory plate. Really simple 4 post configuration inside and all the wires are there, but I cant figure it out without the diagram. Post me back a diagram if you have one to mark.777corp@gmail.comThanksMark

➡️ Reply Pavid

📝 James Epp said:

Hope someone can help me here. I have a pavid generator head, no engine with no id tags. Is there a way to figure out the kw of this unit?I do know this much, Its between 35-90 kw, had a hercules diesel, ( most likly a d3000 or d3400). It is of the design that uses an adapter/spacer to join it to the engine. the fan is inside this section. attaches to a #3 flywheel housing. any help would be appreciated. You can email direct at epp@olypen.com. thanks

➡️ Reply Pavid

📝 Wojtek (VOYTEK) Hajduk said:

Hi,Please quote for motor driver 105-641001 repair.Thank you,Voytek

➡️ Reply Pacific Scientific

📝 debbie mullins said:

I need to get replacement timer pins. Not sure where to purchase this item.

➡️ Reply Paragon Electric

📝 Al Hammersmark said:

Did you ever get the pins? If so from where? Thanks

➡️ Reply Paragon Electric

📝 Eddie said:

looking for trippers for a-309-00amf paragon timer

➡️ Reply Paragon Electric

📝 Kara Willis said:

Hello, do you have any information on where I could get Pavid radiator hoses?

➡️ Reply Pavid

📝 ROBERTO H DAGNINO said:

I need information about a Pavid generator I need parts for this generator,all the information you got on this

➡️ Reply Pavid

📝 Duane Miller said:

We have a Model # 248125, Serial # 1618/s/ng 4023. I need info on this generator, such as natural to lp conversion kit, excitation componennts, manual, and where to get parts for it.Thanks

➡️ Reply Pavid

📝 Richard Wood said:

Hi , I need to know if someone can help me with a Pavid 22KW generator

➡️ Reply Pavid

📝 keith smith said:

A book or parts for a 13k pavid generator.

➡️ Reply Pavid

📝 Tim wood said:

Would be interested in wiring diagram for a pavid genset. Model j18gaw-f. Serial 2378. Thanks

➡️ Reply Pavid

📝 Wendy Minchow said:

I needs filter numbers, oil quantity, coolant quantity, and battery size for a Pavid 65kW model 248269 SN 4599 - this is the only information that is available to me. If you have this information please email me at the email address given above. Any help would be greatly appreciated.

➡️ Reply Pavid

📝 Laurence Beasely said:

I have three 26DL Plus units all working fine except they wont take a charge to the battery pack. The contacts for the battery pack were loose so i resoldered them but no difference. This seems like its a common problem so I was hoping you know the probable fix and you can give me a price to fix them.

➡️ Reply Panametrics

📝 Tony said:

Hi:I need a new pack of rechargeable batteries for a 26DL panametrics..How much will cost with shipping cost to Mexico...(first class priority)ThanksTony

➡️ Reply Panametrics

📝 Tom said:

My upper screen is dim and need it replaced or repaired. Do I need to send the unit or can I buy the part.

➡️ Reply Panametrics

📝 Tom said:

My upper screen is dim and need it replaced or repaired. Do I need to send the unit or can I buy the part.

➡️ Reply Panametrics

📝 max r. williams said:

DO YOU REPAIR PANALARM CARDS AND POWER SUPPLIES THAT ARE DATED BACK TO THE 80S AND 90S WE HAVE APPROXIMATELY 50 UNITS DATING BACK TO THE EARLY 80S

➡️ Reply Panalarm

📝 Roberto H Dagnino said:

I been trying to contact you people a several times,Ineed urgently information about a Pavid generatorModel:J35DWH-DSerial No.:5882/2060Pavid Manufacturing -Co.-Inc.

➡️ Reply Pavid

📝 Roberto Dagnino said:

I need information about a Pavid/SulliarModel:J35DWH-DHours: Reads 940.4Running Condition:Engine runs ok,generator does not work.Engine:White 4cyl diesel,Serial #VL3441144 D230 X308Measurments:59Wide,9 6 Long, 6 Tall. I appreciate your soon response.Thank you.

➡️ Reply Pavid

📝 Roger said:

I just purchased a pavid backup generator. is there parts or service available anywhere for my pavid?

➡️ Reply Pavid

📝 RONALD SEQUEIRA said:

My Partlow 8211011 isnt displaying any readings or power indicators. Need assistance fixing it.

➡️ Reply Partlow

📝 Phu said:

SC125-401-T4 servo motor not responding to commands, causing production downtime. Need urgent troubleshooting and repair to resume operations ASAP.

➡️ Reply Pacific Scientific

📝 murduwiyono said:

Subject Repair Request for Partlow 6130001Hello,I am the inventory manager at and we have been experiencing repeated issues with the Partlow 6130001 unit. Customers have been returning or reporting malfunctions on this unit consistently. Upon inspection of the paperwork and feedback from technicians, it appears that the specific nature of the problem is unknown. We kindly request your assistance in diagnosing and repairing this issue

➡️ Reply Partlow

📝 Scot Campbell said:

Manuals with control drawings available?

➡️ Reply Pavid

📝 vidalis said:

Hi there, I am in urgent need of repair or replacement information for a PARKER CTC P21-2B1-A4-1D3 SINGLE BOARD COMPUTER that has stopped working. Can you provide details on where to find a replacement or how to repair it? Your quick response would be greatly appreciated. Thank you!

➡️ Reply Parker Ctc

📝 Michael Carr said:

Issue PARKER IQAN-XA2 JOYSTICK not responding to movement commands, causing production line operational delays. Immediate repair required to resume normal operations. Requesting

➡️ Reply Parker

📝 SVR said:

Subject Urgent Issue with Panasonic MSD013A1X Hi there, We have a Panasonic MSD013A1X unit that seems to be displaying an error code E34 and is not responding to any inputs. The equipment is currently down and we are unable to proceed with our tasks. Please advise on how to troubleshoot and resolve this issue as soon as possible. Thank you. Best regards,

➡️ Reply Panasonic