Welcome to SIT

We repair a wide range of SIT Equipment.

Ask questions, or 1-336-969-0110 for faster service.

Use the search bar above to find specific manufacturers.

• 40+ years of experience repairing Industrial & Commercial units
• Certified Senior Industrial Electronics Technician
• Ability to do Reverse Engineering
• No job to big or small
• Fast turn around time on most units
• Quality of work comes before profit!
• Old Fashion Customer Service is always the right policy
• Extended warranty
• Fair Estimates
• Low Prices

No repair summaries available yet for this manufacturer.

Comments for SIT

📝 Mike Haverkamp said:

Sitra Automazione VSD 6Drive is showing a L 08 on the digital display before we try to start the spindle. When we try to start the spindle the drive shuts off & goes black. Any suggestions? I need help, my milling machine is down & I have work backed up for it.Thank you for your attention to this matter.Mike Haverkamp

➡️ Reply Sitra Automazione

📝 Dmitry Vernikovsky said:

May by it is very late-on my instruction the L08 it is undervoltage. You must check input rectifier .

➡️ Reply Sitra Automazione

📝 Pete Gallagher said:

The above drive is fitted to a Mecof 5 axis milling machine and controls the high speed finishing head.This is the 2nd occasion that the 4 large capacitors, thyristors, power resistors and varistors on the input side of the drive have failed (exploded), welding the main contactor closed blowing 125 Amp fuses.Following the first repair the machine ran for approx 3 weeks but the same fault has now re occured.After the 1st occasion we thought the input filter may be at fault so we disconnected it and ran the machine without it but now we know this is not the problem.We have replaced all the faulty components but have not tried to run the drive until we hear from you on the issue.We have no manuals or information on the drive to assist us in fault finding or repairs.

➡️ Reply Sitra Automazione

📝 Jim Aarssen said:

Spindle drive VSH tipo vsh6 01VSH6356 I have a problem with this drive and hope you can help me.The display shows L20 and also the cnc control says the drive is not ready.Could you tell me if i could get the manual for this drive that would list all the alarms. Thank You Jim Aarssen email ak2maintenance1@aarkel.com

➡️ Reply Sitra Automazione

📝 R S Raghavan said:

Dear Sir,We have one new CP 800 converter with us. On trying to install this unit we found the parameters were missing in the system. When we tried uploading the parameters through the serial interface of the CP 800 we found the system had no firm ware loaded. Can you please send us the firmware 1-9999 version and procedure for uploading the same. In case there is any cost for this please let us know.RegardsRaghavan

➡️ Reply Sitra Automazione

📝 Krzysztof Pachucki said:

Hello,we need list of errors on Sitra HF converter model CP 800. Can you please send usBest RegardsKrzysztof PachuckiMaintenance EngineerTel: +48 33 499 3731Mobile: 0 785 009 517Fax: +48 33 499 3501PachuckiKrzysztof@eaton.comwww.eaton.comVehicle Group EMEAEaton Automotive Systems Sp. z o.o.Ul. Rudawka 8343-382 Bielsko-Bia³aPolandwww.eaton.com

➡️ Reply Sitra Automazione

📝 Carlos Melo said:

I´m repairing a VSD6 ampli-spindle witch have a problem in brake system.There are two resistances R3 and R4 that I don´t know the value. Can you help me?Ampli-spindle: Sitra VSD 6 sn: 98VSD6252PCB of brake: Sitra 1993-FR.Thanks in advance.Melo

➡️ Reply Sitra Automazione

📝 Genesis mold said:

Digit 165 with C1 control that is giving me a PL2317 VSD Inverter Error 03 - Desaturation ? Any direction would be helpful and appreciated

➡️ Reply Sitra Automazione