Welcome to SM

We repair a wide range of SM Equipment.

Ask questions, or 1-336-969-0110 for faster service.

Use the search bar above to find specific manufacturers.

• 40+ years of experience repairing Industrial & Commercial units
• Certified Senior Industrial Electronics Technician
• Ability to do Reverse Engineering
• No job to big or small
• Fast turn around time on most units
• Quality of work comes before profit!
• Old Fashion Customer Service is always the right policy
• Extended warranty
• Fair Estimates
• Low Prices

🛠️ Common AI Repair Summaries 🏭

Comments for SM

📝 George Banks said:

I have some Smith Geosource units, Model # 550084-0-01 that I am trying to verify the value of the Resistor in location R46. Can you please help me out with this information?

➡️ Reply Smith Geosource

📝 Sales said:

The Shop saidIs the resistor missing from the unit or just open/burnt? If missing or color codes unreadable then we would just draw a schematic of the surrounding circuits and figure out the correct value. If the resistor is open/burnt then cut it in half and remove the metal caps at the end being sure to leave the other metal cap on the end, be careful you only get 1 shot at this. Then measure the resistance from the end to middle and you will be in the ballpark by one of the 2 pieces. If you cant figure it out then send the unit to us.Thanks

➡️ Reply Smith Geosource

📝 Carol Knipschield with Purser Oil Company, Inc. said:

We need a part for the front of our gallon counter. This is used on tanks holding pretroleum products.The number on the reader is S-R61776 and F 788700-019. It is called Site Glass and measures 3X7 1/4We would like to know if the part is available and the price.Thank you for your help,CarolPurser Oil Company, Inc

➡️ Reply Smith Geosource

📝 michael channell said:

model xp e-al impulse transmitter wiring diagram

➡️ Reply Smith Geosource

📝 Ben said:

Can I get a detailed drawing from you for the followingModel: LF4-S1Serial No. BA91879THANK YOUBen Taylor

➡️ Reply Smith Geosource

📝 Dan Hensley said:

My company has recently taken over operations of an oil lease and the equipment bein used to produce the lease. On of the units is a Lact unit with a Smith Geosource SC-13 controller. I need to obtain some kind of manual or paperwork on this unit. Can you help?Sincerely, Dan Hensley

➡️ Reply Smith Geosource

📝 John Vegh said:

Is it the electronic Unit the LEATC. If so I designed it.

➡️ Reply Smith Geosource

📝 andy varenhorst said:

I just started a new job proving meters and would like to know how they work incase i would have to work on one. thanks

➡️ Reply Smith Geosource

📝 Irina Medintseva said:

Dear Sirs!Our Comany participates in project sontruction in S.ARABIAThe Client provided us with a Vendor list including your CompanyPlease conact usfor detailed information.Best Regards,Irina Medintsevasn-pr@sn-pr.com

➡️ Reply Smith Meter Inc

📝 R. R. SARAF said:

Received an alert on the SMC CRB80-90-X291 circuit safety tester - likely a drive or board failure. Will investigate further once I reach the machine.

➡️ Reply SMC

📝 blannybuS said:

Hello, I need repair service for my SMW Systems Inc. SYSTEM 50 controller. The unit is unresponsive and does not power on. I have conducted basic troubleshooting to no avail. Given the high value of the unit, I am wondering about the estimated replacement cost if repair is not feasible. Thank you in advance for your assistance.

➡️ Reply Smw Systems Inc

📝 Clarence Wilson said:

Sir,LB&B Associates Inc. operates a Navy Fuel Terminal. On my truck loading rack we have Smith PD Meters with Controller Valve Model SS1.I have some Bord Assembly that need to be rebuilt.Finding replacements are very differcult.ThanksClarence Wilson

➡️ Reply Smith Meter Inc

📝 Muhammad Asif said:

Dear Sir, Kindly quote your best price for below the following item, earlyaction is requested.Description: Pump Unit CentrifugalPart No: 576139 / 777H440Quantity: 07 EAThanks& Best Regards,Muhammad AsifTHE DABS SYNDICATE

➡️ Reply Smith Meter Inc

📝 MARTIN Michel said:

Our SMW System 30 Rotary Indexer is experiencing operational issues that have been increasingly disruptive to our production line. The unit seems to intermittently lose its ability to accurately position workpieces, resulting in misalignments that affect our machining precision. There are times when the rotary table doesnt rotate at all, stalling unexpectedly, which halts the entire manufacturing process. These problems suggest potential issues with the internal gearing or the control system, both of which are critical to the indexers main functionalities.Given the importance of this equipment in our operations, we are evaluating both repair and replacement options. The estimated cost for replacing the unit with a new SMW System 30 Rotary Indexer is approximately $15,000, factoring in not just the price but also installation and potential downtime. However, understanding the source of these issues could guide us in deciding whether a repair might be both effective and more economically viable. Your expertise in diagnosing and repairing such problems would be greatly appreciated.

➡️ Reply SMW

📝 peegiorpolino said:

SMW RT-5CL motor not functioning properly, seeking repair service urgently. Please respond if you can assist.

➡️ Reply SMW