Welcome to Ta

We repair a wide range of Ta Equipment.

Ask questions, or 1-336-969-0110 for faster service.

Use the search bar above to find specific manufacturers.

• 40+ years of experience repairing Industrial & Commercial units
• Certified Senior Industrial Electronics Technician
• Ability to do Reverse Engineering
• No job to big or small
• Fast turn around time on most units
• Quality of work comes before profit!
• Old Fashion Customer Service is always the right policy
• Extended warranty
• Fair Estimates
• Low Prices

No repair summaries available yet for this manufacturer.

Comments for Ta

📝 Judy Marshall said:

Can you tell me if you have repaired Takuma items? I have a Motor Driver Card part number 00529, and a Motor Driver part number DR24V.Thank You,Judy Marshall

➡️ Reply Takuma Seiko

📝 Bruce Cunningham said:

my SYBRON-TAYLORhas stopped recording the correct speed--at low wind speed the indicator wiggles only a small amount---at high wind speed it moves only slightly up the scale---the cups seem to rotate at different speeds ie as the wind builds to higer speeds the cups rotate faster---as best i can tell like they always have for the last 30 years(ie the unit doesnt owe me anything)-----is there anything i can check/repair short of sending the unit to you or buying a new indicator???? i have checked the flow of current between all connections--seems OK but i dont know what it should be??? my ACV lowest seting is 10---meter shows nothing????-----hope you can give me some good advice---thank you in advance for whatever you can suggest----bruce cunningham

➡️ Reply Taylor Electronics

📝 James S. Chatfield said:

The weathervane rod bent due to some unknown reason and when I took off the top I noticed the vectical shaft was also worn very bad. Do you sell the whole package that sits on top of the roof? The machine was in for repair back in 12/17/82, bought in Sept of 73. Rough weather up here near Rochester, NY where Taylor Instreuments was born. Thank you,James S. Chatfield

➡️ Reply Taylor Electronics

📝 David R. Watson said:

I would like to know if I can purchase the roof unit ( wind/speed indicator and wire )for the 3108 Weatherscope or if I can use a different/more current model that will work as well. I was given the Weatherscope, but I cannot access the weather/wind vane at this time. Thanks, any other info. on this unit would be most appreciated ( Manuals, etc.)David Watson

➡️ Reply Taylor Electronics

📝 Jeff said:

David,I too have become the owner of an older 3108c Weatherstation. I was fortunate enough to get the instruction booklet with it, but like you, I have no roof unit to feed it a signal.Ive looked around the Internet to no avail and wondered if you ever found a source for one?Thanks in advance for any help you can provide.Jeff

➡️ Reply Taylor Electronics

📝 Bill Rizzo said:

Hi Jeff I, also have a Taylor Weatherscope. Im missing the Anemometer & Wind Direction unit. Can you PDF the Booklet that came with your unit? Thank you for your time. Bill of Magic Lantern Productions........Cheers !

➡️ Reply Taylor Electronics

📝 Tom Boscarino said:

I have a NOS Weatherscope 3108 new in the original box. Has never been unpacked or installed.I would like to sell the whole unit. Will take offers.Tom

➡️ Reply Taylor Electronics

📝 TomR said:

Hi:I am trying to repair/replace my Weatherscope but I do not know what a 3108 looks like. Mine is in a chery case and has 4 guages; Barometer, Thermostat, Wind Speed, and Wind Direction.Thanks - TomR

➡️ Reply Taylor Electronics

📝 TomR said:

How do I contact you to discuss purchase? I am interestedthanks - TomR - 215.589.0686

➡️ Reply Taylor Electronics

📝 Brian Heneghan said:

I own an original Taylor Windscope Wind Vane w/ original Wind Direction indicator.After 30 years of service it needs to have the distributor unit either replaced or rebuilt ( currently does not show direction NE thru SE quadrant.What can you do to help ?

➡️ Reply Taylor Electronics

📝 don keating said:

Hello. Did this unit ever sell? Im interested!

➡️ Reply Taylor Electronics

📝 Ray Orobona said:

I am looking for the anamometer cups of the above Taylor weatherscope. One of the cups broke in transit and I need a replacement for only the three cup assembly...not thr bottom sender..However,if I have to purchase the entire assembly I would gladly do so.Thank you,Ray Orobona

➡️ Reply Taylor Electronics

📝 Don Havener said:

I have a complete station that was purchased new in 1976 and never used. Is there a market for such an item?

➡️ Reply Taylor Electronics

📝 william gabriel said:

I would be extremely interested in your weaterscope if you still have it. I had one and would love to have a replacement for it.....Bill

➡️ Reply Taylor Electronics

📝 justin said:

I have a new weatherscope still in box. Call and make an offer 603 608 9670

➡️ Reply Taylor Electronics

📝 Julian said:

Do you sell, or tell me where I can get parts.Thank you

➡️ Reply Taylor Electronics

📝 Tom Whelan said:

Hello:I have acquired a Weatherscope by Taylor (wooden box with 4 gauges) Brand new, never used. It has all the parts except the wind vane for direction.Do you sell them? if not, I cant seem to find a picture of it so I can fabricate one for this unit.Great looking older unit, would love to get it up and working.Thank You!Tom Whelan

➡️ Reply Taylor Electronics

📝 darren said:

we are looking for parts that go from the back of our barameter to the tower. it is a old unit. The only thing I see on it is model E weatherscope by Taylor. It is a wind guage, wind direction, temp and barameter. Thanks for your help. Darren

➡️ Reply Taylor Electronics

📝 Sam said:

I have a Weatherscope by Taylor and the temperature probe is intact and works great, but the wind speed/direction thingie is gone. I have plentry of wire - nothing to connect it to.Can you help me find a new wind thingie?Sam

➡️ Reply Taylor Electronics

📝 Leo McCarthy said:

Have an old? Taylor Weatherscope (cannot find a Model Number) made by Taylor Instrument Company Rochester USA. Has four separate gauges - Max/Min temperature, Barometer,wind speed and wind direction set in a solid wooden cabinet. Cable linking weathervane and wind speed indicator to instruments has been cut. Can you help re rewiring. Can you help re vintage and history of the instrument.Many thanksLeo

➡️ Reply Taylor Electronics

📝 Deb McLaughlin said:

I have the same thing as Leo. My Dad was a weatherman for the County and I inherited this. I would love to use it but I know nothing about wiring. My cable linking the weatervane and wind speed is also cut. There is a very long wire with a metal rod on the end..not sure what that is for. Can anyone give me any information? Im not mechanical but I willing to learn.Thanks Deb

➡️ Reply Taylor Electronics

📝 Thomas J. Vogelpohl said:

Re; Taylor Model 3108A repair person at my home has severly damaged my external thermometer prob/bulb and has also severed the 5-strand ribbon cable which connects the wind-speed/direction unit to the main guage panel. Are there any replacement prob/bulbs and ribbon cables? Is there a 5-pin connector which could be crimped to each cable end to permit reconnection? I am concerned about weather effects on any repair, too.Thank you for any guidance you can offer.Tom Vogelpohl513-232-0356

➡️ Reply Taylor Electronics

📝 John Tucker said:

Hello, Is it possible to purshase a weatherscope or the entire roof mount with the speed and wind direction?Best Regards,John Tucker

➡️ Reply Taylor Electronics

📝 john kolodzie said:

need to replace entire speed cup assembly that fits on shaft.please, advise.

➡️ Reply Taylor Electronics

📝 Gerald Wilgus said:

Do you have a speed cup for a 3108C assembly or do I have to buy the total roof replacement?Thank you.

➡️ Reply Taylor Electronics

📝 John Bouse said:

I have a Taylor Weatherscope but I need the outdoor parts.Are those available?

➡️ Reply Taylor Electronics

📝 Matt Sloan said:

After reading your comments about your sensor, I realized the magnet may be one of the culprits on this issue. Over time moisture accumulates in the magnet and may weaken the field to the induction coil. The induction coil in the Taylor anemometer heads are often weakened by time - temp changes etc. 30+ yrs of use. The coil end braids come undone, but yours is still reading out. There are also two capacitors in the back of the meter and they sometimes lose charge during wind lulls. There are also two adjusting potentiometers in the back of the meter. These can calibrate the windspeed. I find taking a small 6v battery sometimes fills the capacitors back to full thus making the windspeed work again. Just make sure if you do this, to do it momentarily and without the generator unit attached. The Taylor also has a rubber piece in the center of the magnet, make sure it isnt rubbing the bearing plate, it slows the cup operation. You might want to consider a set screw in the outer cup hub, Taylor windspeed generators have a tendency to blow off during windstorms. I have had several 3107s. They are quite accurate if maintained. -Matt

➡️ Reply Taylor Electronics

📝 Noel Declaro said:

I would like to know if you can repair the above mention PCB? How long it take to repair and how much it will cost?

➡️ Reply Tajima

📝 CARLOS MARTINEZ said:

I HAVE A TMEF-H612 EMBROIDERY MACHINE THAT ITS X/Y CONTROLLER IS DAMAGED AND I WANT TO KNOW IF YOU CAN REPAIR THIS BOARD AND HOW MUCH IT WILL COST.

➡️ Reply Tajima

📝 rolly north said:

I have some questions about the wiring diagram. I am using my takagi tk1s for experimental purposes and was wondering if I could modify the amount of natural gas it uses and also modify the way it fires on start up. Any info or help would be greatly appreciated! Thank you!!!!

➡️ Reply Takagi

📝 warner gonzalez said:

I have an embroidery machine tajima temg-g618 but it is does not work only can see in the screen the next code :3d7main shaft motor speed control have some problem .or cpu board is bad .Can you help me?Thank you so muchwarner

➡️ Reply Tajima

📝 Kjeld Jensen said:

We have one TASC unit, Type 132 CD/6. Mod. 4, IP55, Nm 24, Serie nr. 178571-3. 90 V, 3,3 ADCIt has been standing still for some periodes. Now the iron disc with cupper has been corroded ) because off wet environment. Can you offer us a new iron/cupper disc and what is the price and delivery time?Kind regards Kjeld Jennsen, manager

➡️ Reply Tasc Drives

📝 Wesley Ballantine said:

We have a Tasc Unit Variable Speed Drive driving a bitumen pump on a Braham Millar asphalt plant. the plant runs most days for 1 to 2 hrs. we are finding that on start up the unit is slipping and not enough bitumen is delivered to the plant causing the plant to shut down. when it gets going it keeps going ok.Can anyone suggest a repare or part i may need. also consider s/h or new unit. Type = 160CD4/1. serile no =96993. Code = N1 1P55. Mod=3. Nm=33. Many Thanks Wesley Ballantine.

➡️ Reply Tasc Drives

📝 JEFF SHARB said:

WE HAVE A TM-1. HERES WHAT HAPPENS-BLOWER TURNS ON, THEN A 2ND BLOWER. IGNITER SPARKS, BUT WE HAVE NO FLAME. TAKAGI SAYS GAS VALVE(S) ARE OPENING (TECH SAID HE COULD HEAR IT OVER THE PHONE) BUT I DONT THINK THEY ARE. TECH SAID TO CHECK INCOMING GAS PRESSURE. GAS COMPANY CHECKED, MAINTAINING A STEADY 8 WC. GREEN LIGHT ON, LOWER RED LIGHT FLASHING, ERROR CODE 111. ANY SUGGESTIONS? UNIT IS ABOUT 3 YEARS OLD.THANKS FOR ANY HELP.

➡️ Reply Takagi

📝 Cal said:

I am inquiring about getting a replacement of the takamine tk 40 pre amp for an EG523SC I am looking at purchasing one with a possibly bad preamp I am just trying to find out how I can get a new preamp for it if I need to replace it, I cant find anyone selling the tk40 pre amp to replace it with.thanks for your help.Cal.

➡️ Reply Takamine

📝 Mark Naro said:

I have a Takamine EG530 C with a TK4 N preamp pop out of the guitar hit the floor and the case is broken. Now I do not know if the preamp works?

➡️ Reply Takamine

📝 Andy Walls said:

I have no audio or light with fresh battery in preamp. How much to fix this preamp

➡️ Reply Takamine

📝 Paul Aubry said:

I try to know if it is possible to repair or buy a new takamine guitar premp , Graph-Ex preamp???

➡️ Reply Takamine

📝 Widdy Loo said:

My Takamine Electric Acoustic with the Takamine ACCUR Acoustic EQ has about half the volume it should. Battery is good, maybe one of those things in there lost there value and needs to be changed. Is it possible to repair? If so can I just send the onboard unit with out the guitar and pickup? Your reply will be appreciated.Thanks

➡️ Reply Takamine

📝 Val Gladden said:

I have a 2001 graph ex pre-amp and recently the volume pot has been giving me problems. Ive tried cleaning it but it is so sealed up that it is hard to get any spray in there. I even drilled a small hole in the plastic housing and got the same result. I think if I replace it, my problem will be solved. I hate to spend $200+ for an entire replacement, when I can just solder on a new knob. Any suggestions would be appreciated.Thanks

➡️ Reply Takamine

📝 Richard Dunn said:

I have a EG330C with what is, I believe, a bad preamp. It uses the N4B preamp with the RCA plug input and a 3.5MM output. There is no output from the unit. Have switched the 9v and the batt test light does come on. Is there a way to test this? Can it be repaired? I realize that it could be the pickup and dont know haw to determine the issue.Any assistance appreciated.thanks - Rich

➡️ Reply Takamine

📝 Kurt Traynor said:

I am not receiving low end power when plugged into my amp. I get plenty of highs and after talking to someone from Tak they suggested it being the preamp assembly. So, I am looking for a replacement pickup assembly for my Tak fp360sc. If you have these in stock could you please send me a price.

➡️ Reply Takamine

📝 Lynn Waterhouse said:

What would you charge for a house call to Mebane, NC to take a look at my Tajima single head embroidery machine? Please email your reply...Thanks,Lynn

➡️ Reply Tajima

📝 jeard said:

Hi I have a taylor weatherscope and i was wondering if you have the sensors for the wind speed and wind direction? can i send the unit to you and you give me a estimate?

➡️ Reply Taylor

📝 Sharon Casey said:

We inherited the above ... wondering what we need to do to install and get it up and running. Please advise! Thank you!

➡️ Reply Taylor

📝 Frank Giannone said:

can i buy a replacement sending unit for the speed and wind direction for an old Taylor weatherscope.thanks,Frank

➡️ Reply Taylor

📝 Bill Sigle said:

I have a EG544SC-4C with a TK40 preamp that Does not operate properly. It will play through an amp when in the tuner mode, which it is not supose to, but with the tuner turned off its only static or nothing at all. I have removed it from the guitar and there is no visible exterior damage.I would like to know if it can be repaired and how much it woul cost.Thank you.

➡️ Reply Takamine

📝 Nathan Slaten said:

This preamp was missing a pickup that plugged in behind the preamp with a RCA jack. It did however contain with it a 1/8th inch male to 1/4 inch female pigtail for the guitars input. I was curious as to where I might be able to find a wiring diagram for this and another Takamine Pre-amp I am currently working on. Its a Graph-EQ Pre-amp. It has a battery with an LED switch for batt check, a volume control, three band graphic equalizer and an extra fourth slider called an exciter. The other has in place of the exciter a volume gain slider and no knob at all. It seems as though the two units are not working correctly and I believe that it is due to somebody working on them prior to my obtaining them who didnt know what they were doing. A diagram is a must in this situation and any help would be greatly appreciated. Thank you.

➡️ Reply Takamine

📝 Rod Chandler said:

The drive board on your Tajima CX5609030000 is malfunctioning, causing the unit to display errors or be unresponsive during operation. To solve this issue, it is recommended to replace the drive board components. The estimated cost for this repair depends on the extent of the damage and the overall value of the unit.

➡️ Reply Tajima

📝 Richard Parkes said:

Hello, I am in need of repair or replacement information for a TAYLOR 36641-1. The machine stopped working, and we require assistance in fixing it

➡️ Reply TAYLOR

📝 Jerry said:

Subject Tamagawa 800123-2r Repair InquiryHi there,Ive been informed that the Tamagawa 800123-2r unit is not working. Could you please provide assistance?Thank you.

➡️ Reply Tamagawa

📝 neo kim seng said:

Certainly! Could you please provide more details about the behavior of the Tandberg Data 01-w2755d010 that youve noticed in the warehouse? For example, is it making unusual noises, displaying error messages, failing to power on, or behaving erratically in any way? Any additional information you can provide will help me better understand the issue and assist you in troubleshooting the problem effectively.

➡️ Reply Tandberg Data