Welcome to TAK

We repair a wide range of TAK Equipment.

Ask questions, or 1-336-969-0110 for faster service.

Use the search bar above to find specific manufacturers.

• 40+ years of experience repairing Industrial & Commercial units
• Certified Senior Industrial Electronics Technician
• Ability to do Reverse Engineering
• No job to big or small
• Fast turn around time on most units
• Quality of work comes before profit!
• Old Fashion Customer Service is always the right policy
• Extended warranty
• Free Estimates
• Low Prices

No repair summaries available yet for this manufacturer.

Comments for TAK

📝 Judy Marshall said:

Can you tell me if you have repaired Takuma items? I have a Motor Driver Card part number 00529, and a Motor Driver part number DR24V.Thank You,Judy Marshall

➡️ Reply Takuma Seiko

📝 rolly north said:

I have some questions about the wiring diagram. I am using my takagi tk1s for experimental purposes and was wondering if I could modify the amount of natural gas it uses and also modify the way it fires on start up. Any info or help would be greatly appreciated! Thank you!!!!

➡️ Reply Takagi

📝 JEFF SHARB said:

WE HAVE A TM-1. HERES WHAT HAPPENS-BLOWER TURNS ON, THEN A 2ND BLOWER. IGNITER SPARKS, BUT WE HAVE NO FLAME. TAKAGI SAYS GAS VALVE(S) ARE OPENING (TECH SAID HE COULD HEAR IT OVER THE PHONE) BUT I DONT THINK THEY ARE. TECH SAID TO CHECK INCOMING GAS PRESSURE. GAS COMPANY CHECKED, MAINTAINING A STEADY 8 WC. GREEN LIGHT ON, LOWER RED LIGHT FLASHING, ERROR CODE 111. ANY SUGGESTIONS? UNIT IS ABOUT 3 YEARS OLD.THANKS FOR ANY HELP.

➡️ Reply Takagi

📝 Cal said:

I am inquiring about getting a replacement of the takamine tk 40 pre amp for an EG523SC I am looking at purchasing one with a possibly bad preamp I am just trying to find out how I can get a new preamp for it if I need to replace it, I cant find anyone selling the tk40 pre amp to replace it with.thanks for your help.Cal.— Purchase or Repair:

➡️ Reply Takamine

📝 Kurt Traynor said:

I am not receiving low end power when plugged into my amp. I get plenty of highs and after talking to someone from Tak they suggested it being the preamp assembly. So, I am looking for a replacement pickup assembly for my Tak fp360sc. If you have these in stock could you please send me a price.— Purchase or Repair:

➡️ Reply Takamine

📝 Bill Sigle said:

I have a EG544SC-4C with a TK40 preamp that Does not operate properly. It will play through an amp when in the tuner mode, which it is not supose to, but with the tuner turned off its only static or nothing at all. I have removed it from the guitar and there is no visible exterior damage.I would like to know if it can be repaired and how much it woul cost.Thank you.— Purchase or Repair:

➡️ Reply Takamine

📝 Nathan Slaten said:

This preamp was missing a pickup that plugged in behind the preamp with a RCA jack. It did however contain with it a 1/8th inch male to 1/4 inch female pigtail for the guitars input. I was curious as to where I might be able to find a wiring diagram for this and another Takamine Pre-amp I am currently working on. Its a Graph-EQ Pre-amp. It has a battery with an LED switch for batt check, a volume control, three band graphic equalizer and an extra fourth slider called an exciter. The other has in place of the exciter a volume gain slider and no knob at all. It seems as though the two units are not working correctly and I believe that it is due to somebody working on them prior to my obtaining them who didnt know what they were doing. A diagram is a must in this situation and any help would be greatly appreciated. Thank you.— Purchase or Repair:

➡️ Reply Takamine