Welcome to U

We repair a wide range of U Equipment.

Ask questions, or 1-336-969-0110 for faster service.

Use the search bar above to find specific manufacturers.

• 40+ years of experience repairing Industrial & Commercial units
• Certified Senior Industrial Electronics Technician
• Ability to do Reverse Engineering
• No job to big or small
• Fast turn around time on most units
• Quality of work comes before profit!
• Old Fashion Customer Service is always the right policy
• Extended warranty
• Fair Estimates
• Low Prices

No repair summaries available yet for this manufacturer.

Comments for U

📝 Wayne fLEMING said:

Industrial unit 2a500-130h 763-726-45-21 is not functioning, requiring immediate repair. Seeking professional assistance to diagnose and rectify the issue

➡️ Reply Unknown

📝 Sharon Ferguson said:

Looking for O&M data for this system that we installed in 1999 for a customer. Suggestions?

➡️ Reply Unosource Controls

📝 MATT ALLEN said:

Our Unknown 8000 backplane is not powering on or displaying any activity. We need assistance to diagnose and repair the issue

➡️ Reply Unknown

📝 Domingo Galán said:

Received an alert for Unknown 60224 b - drive or board failure. Investigating the issue and will provide updates shortly.

➡️ Reply Unknown

📝 Danny Woolard said:

The Beaufort County School System has the triplex pump system in one of our school systems which is not functioning properly. We are looking for a source of information concerning the unit. We are without any wiring information or sequence of operation manuals. Any help would be greatly appreciated.Ive tried to contact UNOSOURCE without any success.

➡️ Reply Unosource Controls

📝 bharat patel said:

i have a uni mac washer need to repair,not dran porporly

➡️ Reply Unimac

📝 Nizuyir said:

I removed my unimac washer drum for replacement of the bearings in the trunnion.There are two V-rings installed. The outside diameter (OD) is 8.5 inches, and the inside diameter (ID) is 5 inches and thickness is 0.5 inch. I am unable to get the part numbers or suppliers for these items.Could anyone help to identify the parts and also where I can get them.Thank you.Nizuyir Buyong.

➡️ Reply Unimac

📝 BEVERLY Maxwell Newirth said:

I NEED KEY FOR UNIMAC WASHER KEY #3800

➡️ Reply Unimac

📝 Eddie Thomas said:

Where is the nearest service shop located. Need to know the cost for maintenance and repair.

➡️ Reply Unimac

📝 George Park said:

50lb unimac invatar control system.

➡️ Reply Unimac

📝 Viktor said:

Gents, I need P/N for belt for UNIMAC Dryer UB075 E (big one)Thanks

➡️ Reply Unimac

📝 Ramesh Ragha said:

Im looking for a wash motor for UW60P30, slightly used or new, please e-mail me on a price. Thank you.

➡️ Reply Unimac

📝 charles onstead said:

looking for a elect motor for unimac um50p3 washer, unimac p/n 1039266480. voltage 208-240 hz60 wire 4 amps 13 5.5 hp .65kw 530 rpm motor model cp132 c/8-12-2t-4411.please advise price and deliverythanks

➡️ Reply Unimac

📝 A DALIP said:

We hereby seek advise on our UNIOP PLC TOUCH SCREEN UNIT.The screen showing blank when applying power to the unit.Your advise will be highly appreciatedThanks A DALIP

➡️ Reply Uniop

📝 Tom Coffey said:

We have a Exor Uniop plc that the screen light keeps going on/off with power to screen. The plc works fine except we never no when the screen light will go out. Please let us know what can be done to correct this problem.

➡️ Reply Uniop

📝 JAY PATEL said:

WE NEED A REASONABLY PRICED GOOD USED OR NEW CYLINDER AND TRUNNION ASSEMBLY FOR UNIMAC DRYER MODEL # DTB75CGK ALSO CAN USE INNER AND OUTER TRUNNION BEARINGS FOR SAME MECHINE.

➡️ Reply Unimac

📝 bipin v patel said:

WASHER IS NOTY WORKING,FUSE F21 WAS BAD,WHEN WE CHANGE THE FUSE ITS BLOW OUT AGAIN,DURING THE WASH CYCLE.

➡️ Reply Unimac

📝 Politis Anastasios said:

Im still learning, but I was told that the Unknown 76-17956-63356049 is not functioning. Further details or assistance may be needed from someone with more expertise in this unit.

➡️ Reply Unknown

📝 ayman said:

Subject Request for Repair Info for United Technologies ECD67-5116 Control UnitHi ,Im reaching out on behalf of a colleague who is experiencing issues with a United Technologies ECD67-5116 control unit. It stopped working, and we are in need of a replacement or repair. Could you please provide us with information on how to proceed with fixing or obtaining a replacement for this unit?Thank you for your

➡️ Reply United Technologies

📝 Henryfal said:

USB Emhart heel removing machine is not functioning properly, causing a disruption in the production line. The exact issue is unknown, but urgent attention is required to resolve it swiftly and restore operations. Please expedite the repair service to investigate and address the problem as soon as possible.

➡️ Reply Usb

📝 Williamkag said:

Industrial unit Unknown 150-1219 b is experiencing complete power failure, not responding to any commands. Urgently seeking repair assistance.

➡️ Reply Unknown

📝 ron thompson said:

Unknown 310-006 not functioning, needs immediate repair. Looking for a certified technician to diagnose and fix the issue

➡️ Reply Unknown

📝 JABULANI MPOFU said:

Dear Maintenance Team,I observed an issue with Unit 2k9134 in the warehouse. The unit is not functioning as it usually does and is displaying strange behavior. Its unclear what exactly is wrong, but it appears to be acting erratically. Please investigate this issue as soon as possible to ensure the smooth operation of our warehouse equipment.Thank you for your attention to this matter.Best regards,

➡️ Reply Unknown

📝 Olejnik Leszek said:

Unknown 497r not powering on. Looking for a repair technician to diagnose and fix the issue

➡️ Reply Unknown

📝 Daniel Feldman said:

I have a 2 head shuttle Uniloy Needs a good repaiman.

➡️ Reply Uniloy

📝 Sam Newsom said:

Hey team, the UNKNOWN 84-100-00/B METER went down mid-shift. Need someone to check it out ASAP in the morning. Thanks!

➡️ Reply Unknown

📝 Corina Rodea said:

Unknown 8647 not powering on, need repair technician ASAP.

➡️ Reply Unknown

📝 Delcher said:

Im having trouble with the lamp on the microscope assembly. Its not turning on when I try to use it. Im not sure what could be causing the issue, but I really need it to work properly for my tasks.

➡️ Reply Unknown