Welcome to Vonweise

unofficial service & repair forum

We repair a wide range of Vonweise Equipment.

Ask questions, or call 1-336-969-0110 for faster service.

Use the search bar above to find specific manufacturers.

Why to send us your work?

• 40+ years of experience repairing Industrial & Commercial units
• Certified Senior Industrial Electronics Technician
• Ability to do Reverse Engineering
• No job to big or small
• Fast turn around time on most units
• Quality of work comes before profit!
• Old Fashion Customer Service is always the right policy
• Extended warranty
• Fair Estimates
• Low Prices

To receive more information about your unit then fill out the email form below
and we will be in contact with you within 24 hours.

Post Your Problem

🛠️ Common AI Repair Summaries 🏭

Comments for Vonweise

27 comments found.

📝 Dave Henderson said:

I have a VonWeise gear motor model # V02387AB62 serial # D285 that has a cracked gear case casting and I need a replacement. The casting Model # is VW62 and has the part # W2974 on the inside. Is this something you can help me with or advise who could?Thanks,Dave

➡️ Reply Vonweise

        

📝 Linda Orak said:

I have a VonWeise motor model L3096 that is used in a lift chair. The motor stopped working. I was wondering how to get a replacement motor. Can you help me? Ive tried locally with no luck.Thank you,Linda

➡️ Reply Vonweise

                

📝 bill smaney said:

where can i get parts for von weise lift chairsmy phone # is 920 829 5094

➡️ Reply Vonweise

                        

📝 Kristine Polzer said:

I am looking for gearcase cover for a Invacare LC53 Lift chair Serial #97C77045 with a Von Weise Motor.

➡️ Reply Vonweise

                                

📝 Ron Vocht said:

I may need a replacement motor for an electric adjustable bed. Where can I find a Von Weise Gear Co. motor, model VO2898AB76 ? It is a thermally protected electric motor. Volts-115, AC, Amps-1.4, Hz-60, Ph-1, Hp-1/10, Ratio-19:1, Serial-E-78, Shaft-7/16. Does this company still exist?

➡️ Reply Vonweise

                                        

📝 Ken Bensinger said:

I may need a replacement motor for an electric adjustable bed. Where can I find a Von Weise Gear Co. motor, model VO2898AB76 ? The motor is working but the gear box is bad.It has a broken flat bearing and a broken washer in it. it also has a stipped plastic gear.

➡️ Reply Vonweise

                                        

📝 Paul Bowers said:

The bolt holes broke out on the head end. I need a new head cover.

➡️ Reply Vonweise

                                

📝 SUSAN said:

I AM LOOKING FOR A VON WEISE STEP COVER MOTOR MODEL -14943674, 12VDC 8.7A 24:1 SN-L1407. THIS IS FOR THE STEP COVER IN A NATIONAL RV. IF YOU CAN GIVE ME ANY INFORMATION ON WHERE I CAN LOCATE ONE OF THESE THAT WOULD BE GREAT.THANK YOU

➡️ Reply Vonweise

                                

📝 Ron Kadesch said:

I need a working or parts for a Von Weise lift chair operator # 908. Some other # on case- Model VO7647AA76U, also VWE-3 DCF. The motor runs, but the lift shaft doest move. I think the nut or drive shaft must be striped. Can anyone help with parts or info??? THANKS, Ron

➡️ Reply Vonweise

                        

📝 Debra Fauvor said:

I purchased a lift chair from Sears 7 years ago. They used to run a stupid ad campaign Buy it at Sears, get it fixed at Sears. Now they dont want to fix a damn thing. Do you know where I can get it fixed?

➡️ Reply Vonweise

                

📝 Chuck Henry said:

I have a treadmill with a VonWeise V05119AJ76 motor that has a 19:1 gearbox on it. The output screw shaft is bent, but otherwise the unit works fine. Is it possible to get just that replacement part?

➡️ Reply Vonweise

                        

📝 Paul Priester said:

Do you have replacment parts for camper jacks

➡️ Reply Vonweise

                        

📝 Gary Abbott said:

Vonweise model # v00310araa needs new seal, bearing and refilled with gear oil

➡️ Reply Vonweise

                

📝 herman wilson said:

the chair stop in lay out mode I could hear the motor runing but it would not move the chair to let my mother get out of it thank you wilson

➡️ Reply Vonweise

                        

📝 Richard Sieger said:

I have a VonWeise Gear Motor Model V05679CB76U, Serial B1999 that has stripped the main drive gear. I need to replace it. Its the largest gear in the gearbox, which connects to the output shaft? I would also like to purchase a maintenance/repair manual for it, if one is available.

➡️ Reply Vonweise

                                

📝 jessie burns said:

chair will go up but not down

➡️ Reply Vonweise

                                        

📝 Larry Taylor said:

Switching the wires in hand contoller to raise then switch wires again to lower chair. I believe the switch in the hand controller is bad and needs to be replaced. The motor works ok.

➡️ Reply Vonweise

                                

📝 victor said:

I request to quote engines for clinical bedsattevictor

➡️ Reply Vonweise

                                

📝 benny stuben rauch said:

I need the two relays or pc board and relays how ever the part comes for a Von Weise lift chair motor model v05679DL76U serial C2800 cell phone (248) 240-3015 or home phone (586) 777-5469

➡️ Reply Vonweise

                                

📝 Ruth Sprouse said:

Hand control on Vonweise lift chair not working. Chair only works occassionally. Goes up but will not go down. How do I get a replacement hand control, what is the cost for a control and how long is the warrenty?Please call 309-341-3456.Thank you

➡️ Reply Vonweise

                                

📝 jon mitchell said:

have invacare chair w/ vonweise drive. up/stand works ok, down erratic. have to tap relay to get operation of down/recline. looking for repacement relay board pricing and availability. m# V07647AA76U ID# IDI225IBN0252 OPERATOR#H3100 JJS4000M800 VWE-3 INVACARE CHAIR DCF M#LC86 S#00I953361 115vac 60hz 1.0amp 169:1 ratio DC supply P/N PS-00000004 40vdc 2.5amp

➡️ Reply Vonweise

                                

📝 Mike Baldarelli said:

We are looking for a new motor or the upper housing which connects the motor to the chair. The model number is: VO5789AD76U - Serial number: HO896The following numbers were also on the motor: K14003-0001 7190-1935 Type - 90B1Please let me know if you could help.Thanks,Mike

➡️ Reply Vonweise

                                        

📝 Alice Hanna said:

I am looking for a replacement motor for an electric bed. Model #V05789AG76U Serial # H2997 P/N 7190-1935 type 9081can you supply me with one or tell me where I can find one.

➡️ Reply Vonweise

                                

📝 neal said:

the drive gear is all broken up in my lift chair could you please help me. i am trying to take the gear out but there is a pin that runs threw the drive gear how can i take the pin out i would like to see a diagram if you have one thank you neal

➡️ Reply Vonweise

                                        

📝 leon pemberton said:

i need a drive gear set fore m.vo5679dl76u s.c2700 chair

➡️ Reply Vonweise

                                

📝 gerald laws said:

hello the mane gear that makes the chair go up and down is striped out it is a plastis gear on top of the motor that connects to the input shaft what do i need to do to get the gear or have you fix it please resboun thank you and god bless geraldlaws@bellsouth.net

➡️ Reply Vonweise

                                

📝 Peter Winter said:

I am hoping that you will be able to either supply, or tell me where I might be able to locate a replacement for Von Weise gearmotor, Model #V 056 79CB76U, 115 VAC 60 Hz, 1.0 AVWE-1 Ratio 169: 1This is a motor from a lift chair manufactured by the Cleveland Chair Company which is no longer in existence. Any assistance you could provide would be most appreciated.

➡️ Reply Vonweise

                                        

📝 THELMA said:

MY MOTOR DONT WORK SAME MODEL AS YOURS.DID YOU FIND ANY PARTS?OR EVEN ANOTHER MOTOR?IM LOOKING TOO.PLEASE LET ME KNOW.

➡️ Reply Vonweise

                                

📝 Peter Winter said:

I am hoping that you will be able to either supply, or tell me where I might be able to locate a replacement for Von Weise gearmotor, Model #V 056 79CB76U, 115 VAC 60 Hz, 1.0 AVWE-1 Ratio 169: 1This is a motor from a lift chair manufactured by the Cleveland Chair Company which is no longer in existence. Any assistance you could provide would be most appreciated.

➡️ Reply Vonweise

                                        

📝 Steve Webb said:

Can I get a replacement motor, if so how much will it cost.Model# V05679DL76UID# ID10724NO117Serial # D1700 JJ54000MP00Made by Fasco CompanyCall me at 210-416-7789

➡️ Reply Vonweise

                                                

📝 Randy Robinson said:

I would like to know if I can purchase parts for the chair actuator that I am repairing? The large gear that is attached to the screw need to be replaced. The model #v05679dl76u ser #g1000. If not can you direct me to somone that handles the parts for these units. Thank you Randy

➡️ Reply Vonweise

                                

📝 Arnold said:

I have a vo5679cb76u and the electric board is burned

➡️ Reply Vonweise

                                

📝 Jerry Landseadel said:

I have a lift chair made by Golden Technologies, INC. with a VonWeise lift mechanism, model number v05789AD76U, serial number A1497, 115 vac, 60 HZ 1.6 A. The chair is in excellent shape but the mechanism broke. I need a new part.

➡️ Reply Vonweise

                

📝 Dave Burnham said:

We have a VonWeise Motor for our Manitowoc Ice Machine. The shaft is broken that turns the auger. The Transmission model number is WW62. Can we get the transmission without the motor or does that come as a complete unit? Please give us a cost and availibility.Thank You!Dave Burnham Tarta1127 W.Central Ave.Toledo Oh, 43610419-245-5234

➡️ Reply Vonweise

                

📝 Mary Anderson said:

Looking for a Von-weise remote to operate an adjustable bed. Any help?Thanks

➡️ Reply Vonweise

                        

📝 Rob said:

I have a patient with a lift chair that will move in the up position but willnot move in the down position. i am assuming that it is the remote and not the motor. the model Number is :v05679dl76the ID # is ID84072n0073Serial # JJ54000m800The patient uses the chair for sleeping and requires the chair to be fixed ASAPPlease get back to me Thank You Rob

➡️ Reply Vonweise

                                

📝 Rob Johnson said:

Having the exact same problem with chair here also. Has anyone found out how to fix this???

➡️ Reply Vonweise

                                

📝 Jo_Anne Guigue said:

the model V07508AW76U Serial A0902 I found these information on the motor I need the remote . How much is the remote. I live in Canada

➡️ Reply Vonweise

                        

📝 gregg said:

need to find a wireless remote for an adjustable bed. bed has von weise motors with massage motors, model number V07594AB79U.Trancemitter box model number 3433. frequancy 433 mhz rev1.1 . Any help please.

➡️ Reply Vonweise

                

📝 Aaron Tam said:

I have a Von Weise gearmotor, inside the gear box, there is a plastic gear assembly driven by the main shaft. The plastic gear is broken.Can you tell me where can i buy the replacement of the plastic (nylon)gear asssembly in Ontario, Canada if posible.Thank you

➡️ Reply Vonweise

                        

📝 unangeRomonab said:

MARGARITA TRICIA d and down-to-earth Tyler Perry DEMETRICE

➡️ Reply Vonweise

                

📝 Anke Hamalian said:

need to replace this motor.Where I can buy?

➡️ Reply Vonweise

                        

📝 Jim said:

Hi, Need switch for handheld controller. Have one ?? How much ?? Also, service manual ?? Thanks, Jim

➡️ Reply Vonweise

                

📝 Michael L. Walker said:

I have a King Koil elect. bed. About year 1981.The wormgear that drives the up and down motion of the bed, has come out of the motor. I cant tell what is supposed to keep the end of the wormgear in place in the motor. What I am calling a wormgear is a long geared shaft, about 1/2 in in diameter. The back end of the wormgearshould be attached into the motor, as the bedframe rides the wormgear to raise and lower the head of the bed. Any info about what is missing, or why this shaft will nor stay in the motor would be appreciated. I am able to make repairs, if I knew what part or parts are missing, and how to purchase them Motor/drive unit is Von Weise model V03232A876 1/10 h.p. 1.4 amps. 19 to 1 ratio. Serial A-80. Thanks for any help you can provide. Michael Walker.

➡️ Reply Vonweise

                

📝 Gary Marsalis said:

I have a Cleavland Lift Chair with a Von Weise Model Number V07647AA76U Serl. Number K3000,115VAC, Ratio: 169:1 gear motor/actuator. I need the power cord with plug that plugs into the motor control. The plug is white plastic with the female pins in it, it mates to a plug in the control that has two male pins in it.

➡️ Reply Vonweise

                        

📝 millie hinojosa said:

I need the remote control power cord for lift chair serial number L0201. model v07647aa76u

➡️ Reply Vonweise

📝 Howard Bassel said:

Do you supply this type of part or should I go directly to the Company. If you suggest tthat I go to the Comapny, can you supply an e - mail and a phone number.Thank you,Howard Bassel

➡️ Reply Vonweise

📝 Gregg Luebbering said:

I have a problem with a Power Track Jr. ventilation amchine that you manufacture for Hired Hand of Alabama. How can I see a parts diagram of this and determine the part number I need to repair this unit? Thanks so much for responding back to me.

➡️ Reply Vonweise

📝 Stan Thomas said:

Lift chair wont go down. Checked out and lower relay is sticking. Tapped with screwdriver and it started working. Relays are soldered to the board... The chair is fairly old and customer doesnt want to spend a lot on it...as usual. Please give me an estimate. Thanks, Stan

➡️ Reply Vonweise

📝 melanie hamilton said:

We dont know if the bed controller is faulty or if its the motor unit being controlled. Would appreciate any information you might have regarding which it might be. If we know that its the controller for certain...Numbers on control unit:VWE-PD-M003 (zero zero three)Serial number: 22968

➡️ Reply Vonweise

        

📝 HENRY McCUISTION said:

One way to test whether it is your controller or a motor is to switch the plug from the nonfunctioning section (Head, Foot or Bed) into the recepticle for one of the working sections, then use that control button to test the motor itself. Example: If the head does not work but the foot does, unplug the head motor and plug it into the socket for the foot motor. Use the Foot control buttons to raise and lower the head. If the head now works, the problem most likely lies in the controller itself; usually the button itself has failed and the entire controller must be replaced. I am currently looking for a controller myself.

➡️ Reply Vonweise

📝 Kenneth Hoover said:

Von Weise drive assy. used on Invcare adj. bed(mod#V07564AS76U) will raise and lower the head but when in the low height position ,3 to 6 inches, the drive appears to slip back a couple of inches. Keeps slipping back until you reach acertian point then stops slipping back. When just raiseing and lowering works fine. Iam qualified to repair unit. Thank You, Ken Hoover.

➡️ Reply Vonweise

        

📝 Ben Rowden said:

I lost my remote for this bed and was trying to program a logitech harmony remote to control it. Do you know if this is possible?Ben

➡️ Reply Vonweise

                

📝 Rich Angel said:

I have an adjustable bed that appears to have your motor/actuator. The model on the motor is VO7564AS76U. The connecting ring located on the top of the motor has broken and I would like to purchase a new one. Hopefully you can sell/provide that top piece but if I need to purchase the motor and assembly that is fine.A sticker label is on the motor with the name Dunntron and the model number given above. The serial number is KO900 and there are other numbers without description on that same label ... including 100150 and VWG-71; also E32557.Thanks!

➡️ Reply Vonweise

                        

📝 Chetan said:

Need to fix bed the motor want come on need new control

➡️ Reply Vonweise

                

📝 Maria Bartolotta said:

I have two twin ajustable beds...together as a king-size.One bed is no longer adjustable. Is there someone in my location that does repairs for this bed?Model: V07564AS76U115 VAC 60 HZ 2.8AClass B INSUL 40CThermally protectedSerial F2101MO100150VWG-71E32557

➡️ Reply Vonweise

        

📝 norman said:

Smae problem of not holding its position and the head position slowly sinks back down. It only taked to cotter pins to replace this unit on the bed frame so I would like to find a replacement unit if possible.

➡️ Reply Vonweise

                

📝 Equarborirurn said:

Where I can find good quality films?Can anyone help me?

➡️ Reply Vonweise

                

📝 OblilkFib said:

Hi friend i am new to this. Just thought that i would say hello to everyone! dont really know what else to say.I love texting, nothing else to say so bye

➡️ Reply Vonweise

                

📝 mike hetherington said:

I need the controller for my adjustable bed. The only label I can find is on the motor and it has # V07564AS76U. The name is difficult to see but it looks like Dunntron Thanks

➡️ Reply Vonweise

📝 Brad Gooch said:

I am working an an Invacare lift chair with a Vonweise drive mechanism. When I press the button on the hand control the actuator will run one direction but not the other. I have tried a different hand control (pendant) and I get the same result. When I push the button to go the other direction I hear a buzzing sound and that is it. I contacted Invacare and they will not ship individual parts. They want me to order the entire mechanism for around $350. Can you help?

➡️ Reply Vonweise

📝 Jodi Tolbert said:

I need a new control cord for model V00562BF76U, type 90B1 adjustable bed by LeggettThe cord looks like a phone cord

➡️ Reply Vonweise

        

📝 Lynda Dobbin-Turner said:

We have a Restonic adjustable bed, with the above serial number on the body of the control system, but the controls were lost in a move. Need to find a replacement. Suggestions?

➡️ Reply Vonweise

📝 Robert Anderson said:

Do you have something that will replace my two von weise gear boxs & motors? Motors still work but the gear boxes and surrounding parts (woodruff key) et all have given up... Need 2 assembled gear motors with cable if possilbeModel number - V02647AC76 (MF-05) 1/12 HP 1.4 AMP 19:1 RATIO YELLOW L1REDBLUE L2

➡️ Reply Vonweise

        

📝 Tammy McAdams said:

Do you know how to obtain a replacement remote for a Vonweise bed? Its on older model, Model # VO0562BF76U.Thanks so much

➡️ Reply Vonweise

📝 Hector Juarez said:

VonWeise V0574 not powering on at all. Need urgent repair service.

➡️ Reply Vonweise

Contact Us

🚑Shop Location🛠️

Industrial Electronic Repair
145 Rockwell Place Ct
Tobaccoville, NC 27050
🚑 Rush repair shipments only — no walk-ins.

📞Phone

1-336-969-0110

📦Mailing Address🚛

Industrial Electronic Repair
931-E S. Main St #204
Kernersville, NC 27284
📦 Mailing Address (for invoices or shipped repairs)
No walk-ins accepted.

---