Atlas Copco Service & Repair Forum

I work in Jindal Stainless Limited in India..and we has the air compresor ATLAS COPCO( model no-ZR275)...and we has problem with controler ELEKTRONIKON...We are not receiving any display on the regulator inspite of giving a regular 24V supply and its interfacing with SI/O module.Please also send the Input output details of the controller.Schematic diagram for this controller or software for repograming this controller is required.can u help me out in this.Serial nr. 06993100086Part nr. 1900070124

—> Purchase or Repair: Ticket Image

— Posted by GAURAV GUPTA on 2008-10-23

Reply🗨️Ask a New Question Below❓


Recent Comments Search: "Atlas Copco"

If you need your Atlas Copco unit tested or repaired,
give us a call at 1-336-969-0110.
We offer free estimates and extended warranties on the work performed.
Shipping/Receiving:
Industrial Electronic Repair
145 Rockwell Place Ct
Tobaccoville, NC 27050
Phone: 1-336-969-0110

Recent 1316 Comments

#Atlas Copco by Tracey Norouziani on 2012-12-03 05:48
Hi I was wondering if possible if you have the electrical diagram for the ga 45 atlas copco. I\'m getting a error saying \"run phase sequence\" Can you PLEASE HELP? if you have the diagram would you please send me a copy.Thank You Tracey

—> Purchase or Repair:
➡️ Reply
#Atlas Copco by Atul Kanakdande on 2011-01-06 04:38
I need Electronikon controller user manual

—> Purchase or Repair:
➡️ Reply
#Atlas Copco by HARI VEEJAY on 2012-08-09 07:21
air compressor atlascapco GA 37+FF repairing & maintenance manual

—> Purchase or Repair:
➡️ Reply
#Atlas Copco by Matheus Rodegheri on 2012-01-03 13:24
Hello,We need the repair manual of this compressor to make the maintenance. Can you send to me?Regards

—> Purchase or Repair:
➡️ Reply
#Atlas Copco by paimblanc on 2013-05-08 06:27
The controller on my Atlas Copco GA45 1900.0590.74 industrial unit is not functioning properly and needs repair. Looking for assistance to get it back up and running efficiently as soon as possible. Thank you.

—> Purchase or Repair:
➡️ Reply
#Atlas Copco by þþþþþþ on 2008-09-30 12:54
user manuel GA 132

—> Purchase or Repair:
➡️ Reply
#Atlas Copco by zafar ansari on 2010-03-13 08:02
dear sir.we need manuals of ATLAS COPCO GA55AFF for maintenance puropose.Kindly do this favor and provide if possibility is there through soft copy via email.thanks

—> Purchase or Repair:
➡️ Reply
#Atlas Copco by dehner on 2013-08-03 23:32
The Atlas Copco Elektronikon 1900 0701 05 is not working. Please check and troubleshoot as needed.

—> Purchase or Repair:
➡️ Reply
#Atlas Copco by eni on 2012-07-21 08:40
hello! I come near you seek help because we have an air compressor atlas copco who is in default, what is written on the screen \"system failure 104\" but we no longer have the manual, thank you votrebcomprehension and soon

—> Purchase or Repair:
➡️ Reply
#Atlas Copco by DIMITRIS ZAOURIS on 2008-05-08 09:05
Dear sirWe are a food industry in Greece and we have two ATLAS COPCO GA115air compressors and i have a problem with the keyboard of the one unit.The electronikon screen works but when i want to change parameters the push buttons not work.I think that i need only the front keyboard.Can you provide th…Purchase or Repair: Ticket Image...
Show More
➡️ Reply
#Atlas Copco by sahaya bosco on 2011-01-19 15:17
GA37 make compressor running time convertor failure fault came also comprerssor totally tripped, why this fault came and how to rectify that fault?

—> Purchase or Repair:
➡️ Reply
#Atlas Copco by dhayalan on 2011-05-26 06:53
sir, please send the manual of elektronicon ii to service atlas capco compressor.thank youwith regardsDhayalan+91 9952760682

—> Purchase or Repair:
➡️ Reply
#Atlas Copco by george kwaramba on 2011-07-21 15:25
Good service so far

—> Purchase or Repair:
➡️ Reply
#Atlas Copco by Snead on 2008-08-25 16:18
Please help us determine if the Atlas Copco 1900 0701 02 Elektronikon unit is still supported or if replacement parts are available. Thank you.

—> Purchase or Repair:
➡️ Reply
#Atlas Copco by Omar THIAM on 2009-05-20 14:23
Bonjournous avons deux compresseur Atlas COPCO ZT45 et ZT22 dans notre usine de production de boisson Coca Cola. je suis le Utilities Manager et depuis mon arrivée j\'ai aucune documentation sur le module de commande Elektronikon et le manuel de maintenance.merci de nous envoyer en PDF si possible c…Purchase or Repair: Ticket Image...
Show More
➡️ Reply
#Atlas Copco by supria on 2011-09-23 10:33
I NEED SERVICE & OPERATING MANUEL FOR ATLAS COPCO GA55THANKS.

—> Purchase or Repair:
➡️ Reply
#Atlas Copco by Morris Bujarski on 2008-04-02 20:46
We have a Atlas Copco GA 18 FF w/ Elektronikon ll control. But we have no manual for the Elektronikon control. Could I get this on pdf file?

—> Purchase or Repair:
➡️ Reply
#Atlas Copco by José Valdir dos Santos on 2013-08-16 22:32
The Atlas Copco Elektronikon 1900 0701 05 unit is still down. Please provide a

—> Purchase or Repair:
➡️ Reply
#Atlas Copco by bishelnoor on 2012-03-20 07:48
very good comprossor and it very easy to serves and operate .little faulte and give enough pressure.

—> Purchase or Repair:
➡️ Reply
#Atlas Copco by carlson on 2014-11-27 00:14
The Atlas Copco Elektronikon II 1900071011 is not operational. Can you please help look into this issue?

—> Purchase or Repair:
➡️ Reply
#Atlas Copco by Syaiful Bachri on 2011-04-20 08:47
I have two Compressor Atlas Copco GA.37, and operation 1998 until now.I think series GA.37 very good. I need Manual Book & Part list because my book lose, so i need you for that.

—> Purchase or Repair:
➡️ Reply
#Atlas Copco by Maximo D. Otadoy, Jr. on 2009-05-26 02:21
Recently the Elektronikon Controller of our GA 37 Atlas Copco Air Compressor indicated \"Total Systems Failure\". Attempts by local Atlas Copco personnel to redownload program files were not succesful. Can this controller be repaired by you? If Yes, can this be loaded with program so that we will ju…Purchase or Repair: Ticket Image...
Show More
➡️ Reply
#Atlas Copco by shailendra kumar gaund on 2010-12-22 14:28
hi i am asking u if u could please send me a copy of the operation and trouble shooting manual for the GA7 compressor . for elektronicon controller is truble . please send me trouble shooting manual.thanks & regards.shailendra kumar

—> Purchase or Repair:
➡️ Reply
#Atlas Copco by Luis Alcantara on 2011-08-24 16:18
Hi my name is Luis and i need a manual of elektronicon mk4 and mk3 for specifications of the compresor and display thankz for ur help

—> Purchase or Repair:
➡️ Reply
#Atlas Copco by Faizal on 2015-05-26 04:53
Hello we operating oil free compressor ZT110 and the electronikon displays an error which reads as follows: system failure 7001please send me trouble shooting and solution to this problem.thank you

—> Purchase or Repair:
➡️ Reply
#Atlas Copco by JERRY TOO on 2010-03-04 03:49
DEAR MR/MS, I NEED YOUR HELP. DO U POSSIBLE SENT ELEKTRONIKON 1900 0700 03 OF THIS UNIT INSTRUCTION MANUAL FOR US? BECAUSE WE GET SOME PROBLEMS FOR THIS UNIT. AND PLEASE REPLY AS SOON AS POSSSIBLE. THANK YOU VERY MUCH!!!

—> Purchase or Repair:
➡️ Reply
#Atlas Copco by Reinier Swanepoel on 2014-02-20 02:00
Changed out display panel about 6mnth ago, display stops working again. Tested the supply and found 24v going in but display is not working . Could it be a coincident or maybe a bad display panel.Advice

—> Purchase or Repair:
➡️ Reply
#Atlas Copco by waleed ALKHATEEB on 2010-04-30 12:14
DEAR SIR I am working in JORDAN PHOSPHATE COMPANY JPMC We used GA-90.compressor year of manuf. in 2001 Now, we have a problem on the Elektronikon Control Module we have massage error 104 system fault we don\'t have document \" manual of Electronikon\". You can hepl me, send for me document.and help …Purchase or Repair: Ticket Image...
Show More
➡️ Reply
#Atlas Copco by FRANCISCO SOLIS on 2008-02-21 16:57
is free cost

—> Purchase or Repair:
➡️ Reply
#Atlas Copco by Jacek on 2013-07-03 15:39
I need repair for my Atlas Copco GA45 1900.0590.74 controller. It's displaying an error message and not responding to adjustments. Can someone come out to inspect or repair it as soon as possible? Thank you.

—> Purchase or Repair:
➡️ Reply
#Atlas Copco by cal on 2012-08-05 10:24
My Atlas Copco 1900-0700-08 controller is displaying an error code and not responding. Looking for a technician who can diagnose and repair the issue

—> Purchase or Repair:
➡️ Reply
#Atlas Copco by chakramanikyam on 2013-06-07 11:40
Dear Sir,we have the atlas capco compressors in our plant in that on of the compressor is tripped and in display is showing some codes, but we unable to decode the code due to the lack of instruction manual. So that kindly request you to please send the operation and instruction manual to us for fau…Purchase or Repair: Ticket Image...
Show More
➡️ Reply
#Atlas Copco by mike vander heiden on 2015-07-23 15:43
I'm having trouble with my Atlas Copco Elektronikon II 1900071012, which is a Compressor Controller. There seems to be an issue with its functionality it's not working as expected.

—> Purchase or Repair:
➡️ Reply
#Atlas Copco by samir on 2010-11-03 14:30
atlas copco meilleur constructeur

—> Purchase or Repair:
➡️ Reply
#Atlas Copco by Ngoni Gunundu on 2008-02-21 07:18
We have an Atlas Copco Elektronikon Systems ES300 central governor which is down. I want to have it repaired so i need your assistance.

—> Purchase or Repair:
➡️ Reply
#Atlas Copco by Allan on 2012-03-29 13:34
GA 160

—> Purchase or Repair:
➡️ Reply
#Atlas Copco by musa batari on 2008-06-02 16:28
we have twoof this type of compressor in my section for bag filters, resently we had a problem of the display unit went off completly. we try to trace the problem but is difficult becouse the circuit diagram was too tiny to read. pls. can you send a pdf copy to me so that it will help to trace any p…Purchase or Repair: Ticket Image...
Show More
➡️ Reply
#Atlas Copco by Macdonald on 2013-08-21 12:32
Our Atlas Copco Elektronikon 1900 0701 05 unit is still down. We need urgent assistance. Please respond

—> Purchase or Repair:
➡️ Reply
#Atlas Copco by rahimi on 2010-04-01 19:58
Dear Sir,we need maintenance manual of GA75 Air Compressor(Oil inject compressor).please send us of it.we are waiting for your reply.regards.rahimi

—> Purchase or Repair:
➡️ Reply
#Atlas Copco by saad on 2010-10-20 09:54
Dears, I need a help for a failure massege of elektronikon panel which its part no. is (1900 0710 31). the failure massege is :22200000210000009820 3978 10 when i run this panel, this massege appears and remains in display without any change and no step done yet!please, advice me for this problem an…Purchase or Repair: Ticket Image...
Show More
➡️ Reply
#Atlas Copco by GANESH on 2009-06-06 12:45
dear sir, i have elektronikon II unit but some problem is inside i want some information ragarding cirquit digram or IC Details used in unit i hope u will give me response kindly.. Thanks ganesh

—> Purchase or Repair:
➡️ Reply
#Atlas Copco by Charmaine on 2011-06-13 12:05
we need the wiring for the pannel

—> Purchase or Repair:
➡️ Reply
#Atlas Copco by Nia Kurniati on 2008-04-06 02:36
How can I found user\'s manual for elektronikon control modul type ES 100

—> Purchase or Repair:
➡️ Reply
#Atlas Copco by Chookeat T. on 2008-10-01 10:55
Dear Sr.I Need ELECTRONIKON II technical Manual.Best regards,Chookeat T.choo_oh@hotmail.com

—> Purchase or Repair:
➡️ Reply
#Atlas Copco by NILEAYSH GHODAKE on 2013-07-22 23:32
The Atlas Copco Elektronikon 1900 0701 05 unit in the shop is not working.

—> Purchase or Repair:
➡️ Reply
#Atlas Copco by ThanhDat on 2011-04-03 07:38
Dear service Manager!We are using Atlas Copco Compressor GA 15, A MESSAGE IS APPEARING IN LCD THAT \"SYSTEM FAILURE 200\"PLS TELL ME THAT HOW I CAN REMOVE THIS ERROR ,PLS REPLY ME URGENTLY.THANKS

—> Purchase or Repair:
➡️ Reply
#Atlas Copco by Florentino Lagumbay on 2006-08-18 03:08
My client need this replacement part 2pcsAtlascopco Elektonikon, PN 1900 0701 23control type, 24 VACPls email quotation to : porkydouglas@yahoo.com

—> Purchase or Repair:
➡️ Reply
#Atlas Copco by PANKAJ on 2014-08-20 12:22
Dear , sir I have used ZR-250 comp. in moserbaer india limited. So alarm comes on -110300000000 . so please clear this alarm . what is alarm reason . urentlyReg.Pankaj

—> Purchase or Repair:
➡️ Reply
#Atlas Copco by Wayne Ellis on 2010-02-05 17:29
Could you supply a user manual for the elektronikon controler

—> Purchase or Repair:
➡️ Reply
#Atlas Copco by SOUNG on 2010-04-08 11:53
The Atlas Copco Elektronikon 1900070124 controller is malfunctioning, causing a halt in our production line. We need immediate repair service to resolve this issue and resume normal operations swiftly.

—> Purchase or Repair:
➡️ Reply

Contact Us

🚑Shop Location🛠️

Industrial Electronic Repair
145 Rockwell Place Ct
Tobaccoville, NC 27050
🚑 Rush repair shipments only — no walk-ins.

📞Phone

1-336-969-0110

📦Mailing Address🚛

Industrial Electronic Repair
931-E S. Main St #204
Kernersville, NC 27284
📦 Mailing Address (for invoices or shipped repairs)
No walk-ins accepted.