Procond Elettronica for Service call 1-336-969-0110 at Industrial Electronics Repair

Procond Elettronica Service & Repair Forum

DZ4 A and B are both the same which turn out to be 12 volt 5 watt. for an upgrade you can only go so high on the voltage and from what NTE says 13 volts keeps the diodes cool enough. Also if you solder them in, don\'t push them to the board. Let them sit up some to allow total venting around the diode. I never replaced DZ1, but DZ4 A and B were toast when I initially tested them.

— Posted by mark on 2007-03-08

Reply🗨️Ask a New Question Below❓

If you need your Procond Elettronica unit tested or repaired,
give us a call at 1-336-969-0110.
We offer fair estimates and extended warranties on the work performed.
Shipping/Receiving:
Industrial Electronic Repair
145 Rockwell Place Ct
Tobaccoville, NC 27050
Phone: 1-336-969-0110

Recent 272 Comments

#Procond Elettronica by Tom R on 2005-07-23 14:45

I have a PWM Motor Controller card from a Proform treadmill that seems to be not working. Please email me. Thanks

#Procond Elettronica by Joseph Krug on 2005-11-23 01:08

I received the MC-70 motor controller board back today. It works perfectly, and I wish to thank you for your one-day turn around time and quick return shipping. Your service is better than you advertise, which is unusual and greatly appreciated.Thank You again!!!A very satisfied customer!!

#Procond Elettronica by Fred Santizo on 2006-01-29 05:40

Dear Sir/Madam:I need a device with tree switches. It must create the PWM to control the speed of a treadmill motor controller. One of the switch will turn on/off the treadmill the other two will be use to increase/decrease the speed of the motor or the treadmill. I want to eliminate the console of ...
Show More

#Procond Elettronica by Lloyd Anderson on 2006-02-01 17:26

Howdy! I was hoping to find out whether my procond board made to you folks through the mail and if so what the turnaround time might be. thanks, Lloyd

#Procond Elettronica by kenneth Anderson on 2006-02-04 02:00

I would like to thank the people and Industrial Electronic Repair for repairing a mc-70 motor control boad. I was working on an elderly couples treadmill and found the control board defective, when I contacted Industrial I explained how they were elderly and didn\'t have a lot of money. Industrial o...
Show More

#Procond Elettronica by EDDY MEDINA on 2006-03-01 21:15

I have an MC-70 motor controller that is not working from a Reebok ACD2 treadmill and I would like to know how do I get this part repair or replace. Please call me at your earliest convenience at (1917)662-2892 or email me asap. Thanks EDDY MEDINA

#Procond Elettronica by Sonny Ta on 2006-03-05 20:13

I need to find out what is the repair or replacement cost for this part , part # 124438, and the turn around time if I send it in. What is the best way to send in the part for repair ?orIf I decide to buy the part, how much would it cost ? Include shipping and Handling .Thanks.Sonny

#Procond Elettronica by Geo Suchora on 2006-03-29 01:09

I am a business customer contacting you regarding my Procond Elettronica 356033305 circuit board. The unit seems to be malfunctioning as it is unable to power on or function properly. There are no visible signs of damage or any other external issues that may have caused this problem. I suspect there...
Show More

#Procond Elettronica by Duanna Jorgensen on 2006-03-30 23:23

I have an AMF 7 day Paragon Timer. It controls my motor on my septic system. The problem is that it seems to run continuous, and I have no book to explain to me how to set the timer. Is there a way to find a manual that will explain this to me? I bought the house, and the system was already in. I ha...
Show More

#Procond Elettronica by marcus thomas on 2006-04-21 19:24

What are the type and specs for the Diodes on this Controller board? They are located in the DZ1 and DZ4 positions. Also, is the resistor that is located ajacent to these Diodes the best size? if not what do you recommend?

#Procond Elettronica by Keith Haufler on 2006-05-19 22:42

I am having trouble with my powertread nordictrack treadmill PT 6.0 and have traced power into the controller. I checked the DC motor by hooking it up to a drill battery and it works fine. What part usually fails on these things? If I need to a replacement, what will it cost? Is it cheaper to send y...
Show More

#Procond Elettronica by Xhuneyt on 2006-06-03 16:22

I have a problem with a motor controler for waching machines, and i wanted you to help me about this. It has not enough force to roll the clothes. I changewd the chip, but it is still not working properly. The code: 3 560 332 06

#Procond Elettronica by Jeff Haag on 2006-06-16 02:00

I believe my MC-70 controller board may be bad. Do you repair these boards? Is this board manufactured by Procond Elettronica?Thanks.

#Procond Elettronica by Dwight Holder on 2006-06-20 22:34

I need DZ-1 and DZ-2 diodes or their values.Or what is the repair cost of this item.Thanks

#Procond Elettronica by J. Haag on 2006-09-01 20:58

I have an ICON MC-70 motor controller for an IMAGE 10.8q treadmill (IMTL 19372), serial #K23693147 that requires repair as the controller is not functioning correctly. I believe the ICON part number for this controller is #152004. Do you fix these motor controllers?If so, what is the price range for...
Show More

#Procond Elettronica by Jon Schniers on 2006-10-05 16:06

Donna Im serious I will buy you dinner if you get me the part values and schematic for the MC-70 Controller.My number is 517-546-8314 Jon

#Procond Elettronica by Paul Brain on 2006-12-05 10:31

I have a Damamaged control board for the above washing machine. The procond type number is 3560 041 10 AI am trying to get hold of the circuit information for this board.Can you help ?

#Procond Elettronica by Larry Nadler on 2007-01-20 15:40

Got the board back and it works great! Amazing turn around time....you got in on a Friday and I had it back the next Wednesday....Unheard of especially with a check in the box for payment! Did you change anything else besides those 2 Zener diodes to heavier duty components? Thanks again.....Do you w...
Show More

#Procond Elettronica by Marco Garcia on 2007-02-03 04:46

I need schematics for the MC-70 for Proform 985 CD treamill. Where can I get a copy?

#Procond Elettronica by Joseph on 2007-02-03 22:39

Can you please advise what it would cost to repair a MC-70 board for my Nordic Track treadmill? The power supply board has all the LED\'s lit (the PWM flashes only when it calls for speed). The motor works (I\'ve used a 12 vdc power supply to test). I\'ve also checked to make sure that 120Vac is sup...
Show More

#Procond Elettronica by Marco Garcia on 2007-02-07 23:10

What are the replacement for DZ1 and DZ4 on the MC-70 board. I am looking for a p/n for DZ1 and DZ4. This will fixed my Mc-70I figure out DZ4 to be a zener diode 24V, 25mA, 1.5W and got a replacement zener diode 24V, 50mA, 5W but I do not know about DZ1. I need info on DZ1 zener diode voltage, and c...
Show More

#Procond Elettronica by Cristian on 2007-03-02 22:49

Hi, I\'ve a faulty Procond Elettronicatransformer for a switching power supply.The label says \"Procond Elettronica 411070276\"and the case is green.Can you help me in finding a replacement part ?ThanksCristian

#Procond Elettronica by jivat on 2007-03-07 18:14

The treadmill IMAGE 10.6Q has the KEY missing.Can you please provide us the Key or recommendwhere I will be able to get it.Thanks

#Procond Elettronica by mark on 2007-03-08 23:48

DZ4 A and B are both the same which turn out to be 12 volt 5 watt. for an upgrade you can only go so high on the voltage and from what NTE says 13 volts keeps the diodes cool enough. Also if you solder them in, don\'t push them to the board. Let them sit up some to allow total venting around the dio...
Show More

#Procond Elettronica by mark on 2007-03-24 03:30

Marco,I had a long conversation with a few people and here is what we have come up with for the MC-70 Board.Now depending on the versionDZ4- is the 24V,50ma,5watt zener ORDZ4A and DZ4B- are 12V,650ma,5watts each in series.DZ1- is 15V, 0.2a,1wattDZ2- is a 3.9V, 20ma, 1/2wattI have replaced them as re...
Show More

#Procond Elettronica by Sebastian Voss on 2007-03-27 16:08

Hello,I have a refrigerator and inside ist a plateType Procond 452747163 sw NGBF0A1L242523719 ERF2000P-01.D 220/240V 50Hz - ERF2000PBon this plate is the part, which ist marked with \"T1\" (a transformator)broken.Can you sell it to me, and what is the price.ThanksSebastian Voss

#Procond Elettronica by Uwe Jungbauer on 2007-05-21 09:30

Dear Sir In our Electrolux dishwasher W60, we have the printed circut, typ: 356083206. My question is, if we can get this part checked in Hungary or in Austria?With regardsUwe Jungbauer

#Procond Elettronica by ELBASSRI on 2007-06-02 14:41

HelloI would like to test this module, i don\'t know if it\'s working well Is it possible to have a schematic or technical datasheet of this moduleRef = Type P:451510051 F : 6210Type E: 12430392/5SW ver W2C01250 9/01THANKS A LOTBEST REGARDS

#Procond Elettronica by michael on 2007-06-02 20:05

HelloI would like to test this module, i don\'t know if it\'s working well Is it possible to have a schematic or technical datasheet of this modulename of washing machine gyzer san gorgo modole number 3 560 332 07

#Procond Elettronica by Kevin C McCurrie on 2007-07-13 00:19

Hi, I had the code E21 and had a repair service check all of the components. They concluded that the console had to be replaced and it isn\'t made anymore. I found one seller for $499.00 and it is too much. Its a shame because it was a good treadmill.

#Procond Elettronica by randon on 2007-08-09 13:55

HelloI would like to test this module, i don\'t know if it\'s working wellIs it possible to have a schematic or technical datasheet of this moduleRef = Type P:451510073 Type E: 12430382/1WL401009THANKS A LOTBEST REGARDS

#Procond Elettronica by Matthias on 2007-08-25 10:29

Dear Sir In our Ariston dishwasher LSI 62 A, we have the printed circut, typ: GE Precond Elettronica 356084601. My question is, if we can get this part checked or buyed in Germany?With regardsMatthias

#Procond Elettronica by MARTIN Alain on 2007-09-09 14:48

HelloIs it possible to have a schematic or technical datasheet of this module :Type P 451510061 F:6210Type E 12430392/7SW ver W2C013T2 31/01BEST REGARDS

#Procond Elettronica by Reimert on 2007-09-30 14:53

HelloIm also would like to test this my module, i don\'t know if it\'s working well Is it possible to have a schematic or technical datasheet of this module *******Waht is the cost for repair? What is the cost for a new one?GE Procond ElettronicaType P. 451510051 Type E. 12430392/5SW Ver. W2C01250 2...
Show More

#Procond Elettronica by PAUL MITCHELL on 2007-10-05 15:57

HI THERE COULD YOU TELL ME THE PRICE FOR A NEW PART FOR A PROCOND ELETTRONICA PART NO 411122430 OUT OF A ZANNUSI WASHING MACHINE.MANY REGARDS PAUL.

#Procond Elettronica by johnny liu on 2007-10-18 17:42

I need DZ1 and DZ24 diodes. Both appear to be burned. Can I repair them?Thanks,Johnny

#Procond Elettronica by johnny on 2007-10-18 20:17

where to buy these diodes?Thanks,

#Procond Elettronica by Sergio Dratwa on 2007-11-13 06:23

Elevation motor is working properly, drive motor does not starts.There are 2 diods that are burn: DZ1 and DZ4 (in between the relay and what look like to be 2 ceramic resistors). There is an overheat area on PCB under these diods, but PCB still OK.Would you sell me just the diods?If not, how should ...
Show More

#Procond Elettronica by james on 2007-11-28 00:56

I replaced DZ1 and DZ4 for my Reebok ACD2 per Mark\'s comment, and it works fine now. Great thanks to Mark\'s info. -james

#Procond Elettronica by henry gutierrez on 2007-12-02 22:58

MORNINGYOUR HAVE PARTS ELETRONIC OF TRADMILL AND BICYCLE UNIVERSAL MUCH MODELS FOR REPAIRTHANK YOUSINCERELYHENRY L.R. GUTIERREZ

#Procond Elettronica by roger moutal on 2007-12-10 22:48

Hi,COULD YOU TELL ME THE PRICE FOR A NEW PART FOR A PROCOND ELETTRONICA PART NO 451511735 . AND ALSO THE PRICE FOR A TRANSPORTATION TO FRANCE.THANK YOU

#Procond Elettronica by A. Redd on 2007-12-22 19:29

Proform 725si (PFTL 72560) board ID 170-0518 rev. 2.Do you have replacement board (new or refurb.)? What is the cost to repair?

#Procond Elettronica by Gianfranco Manunta on 2007-12-26 18:07

Hi,COULD YOU TELL ME THE PRICE FOR A NEW PART FOR A PROCOND ELETTRONICA PART NO 356071101 - LABEL NO 452650111 - FOR Ariston dishwasher LSI 66 A. AND ALSO THE PRICE FOR A TRANSPORTATION TO ITALY.With regards, GIANFRANCO MANUNTA, via M. Macchi 87 - 20124 Milano - ItalyTHANK YOU

#Procond Elettronica by Eric Tibbits on 2008-01-05 21:41

I have been having problems adjusting the maximum speed potentiometer for my treadmill. I am not an electrical guy. Could you send me a drawing showing the location of this part so I can fix my treadmill. Thanks

#Procond Elettronica by jimig on 2008-01-20 19:43

What is the cathode of DZ4 connected to via PWB traces top and bottom?Due to the heat from DZ4\'s overstress is looks like if there was a trace to DZ1- it vaporized.Are the cathodes of DZ1 and DZ4 connected?

#Procond Elettronica by Janclakson Silva Souza on 2008-02-10 12:10

part supply number: EN 132400

#Procond Elettronica by Tom Mitchell on 2008-02-19 11:27

Hello, I am a business customer seeking repair service for my Procond Elettronica MC-70 124438 treadmill board. The unit is exhibiting an issue where it fails to power on despite being connected to a power source. I have attempted to reset the unit multiple times without success. Based on initial di...
Show More

#Procond Elettronica by roberto arreola on 2008-03-20 02:51

Iwant to now the price in this part

#Procond Elettronica by james bryan on 2008-03-20 12:56

we need to t know the replacement cost for this item.Brand:gepruft#vc50er 9pi2004-22-lch3105

#Procond Elettronica by Pasquale Martusciello on 2008-03-25 17:53

My dishwasher Ariston LSI 61 E has broken down.Please How Much cost the board sended to Italy in caserta.Thanks

#Procond Elettronica by Andrew on 2008-04-01 17:51

Depending on the version you have....DZ2 = 3.9V 1/2Watt (replace with higher wattage)DZ1 = 15V 1 watt (replace with 5 watt)DZ4 = 24V 5 watt-OR-New versions haveDZ4A and DZ4B = 12v 5 watt eachResistor is 1K, I replaced it with a 10Watt wire wound 5%.

#Procond Elettronica by Charles on 2008-04-12 02:36

I have the same problem with mine. If I could get a value on these diodes, I could replace them. I need DZ2 and DZ4. I would like to have a schematic on this board.

#Procond Elettronica by Dejan Pantelić on 2008-04-17 10:33

Dear Sirs,please send your best offer for following items: GE INDUSTRIAL FILTERS: 1. TYPE RANGER 520-280 2 PC 520 V AC, 50-60Hz, 0345, 280A, 40 degrees C, 82480 high leakage current connect protective earth first 2. TYPE RANGER 520-450 1 PC 520 V Ac, 50-60Hz, 0150, 450A, 40 degrees C, 80447 high lea...
Show More

#Procond Elettronica by Ged McDaid on 2008-04-26 22:02

My treadmill seems to wish to go max speed regardless I have tested the potentiometer it is ok/Can you repair the mc-76?Can you supply to the uk?Cheersged

#Procond Elettronica by Jean-Marc CARREE on 2008-05-05 09:16

Hello,I have a dishwasher Hotpoint Aquarius FDW60.(The guarantee is over). And a Procond part in it is burnt, then I want to know if it\'s possible to order this part :Procond Elettronica 41326005P/N : EN132400If it possible could you transmit me the price and how can i do that, please?Thank you.Bes...
Show More

#Procond Elettronica by Nestor Juguera on 2008-05-26 23:32

need schematics for the 356069403 for even microwave delonghy mw605/3. Where can I get a copy?

#Procond Elettronica by Charles Ray on 2008-05-28 13:34

I have a sears treadmill with mc-70 motor controller #124438 that has shorted diodes. I would like to have a price on repairs or replacement.Thanks Charles

#Procond Elettronica by jeff on 2008-06-01 16:13

what are the values? i assume they are zener diodes, since the other diodes are labeled d10, d15, etc without the Z

#Procond Elettronica by jeff on 2008-06-01 16:43

anyone know the values of dz2 and dz4luserjeff@yahoo.com

#Procond Elettronica by Jeff Northam on 2008-06-20 17:10

I need a replacement board or the diodes replaced on a circuit board with #509130200 for a motor control unit (part number FR 131146900) from a White-Westinghouse LT 350R front loading washing machine.

#Procond Elettronica by Dan Baldauf on 2008-06-20 23:44

I have a treadmill that when turned on starts slowly for about 1 minute and then shuts down. it displays an Er2 error message. Any thoughts on what is wrong the cost it might be to fix it.????Dan

#Procond Elettronica by Bobby on 2008-07-31 00:56

Replaced the diodes like all others. Replaced the big resistors as well. Still not working. Getting 130v out from the motor +/- but the motor isn\'t turning. There is a lot of corrosion near this board, as if the previous owner spilled something and maybe shorted out the board. Is there supposed to ...
Show More

#Procond Elettronica by János Madarasz on 2008-08-10 18:58

Wellcome!I would like to know conecting up of 356069403 microwave.How can you help me ?Sincerelly János Madarasz

#Procond Elettronica by laurence hamilton on 2008-08-19 02:25

I need a value for R57 &wattage rating on the above mc-70 pcb.

#Procond Elettronica by Jim Cox on 2008-08-22 00:59

Did you find the value for this power resistor? I\'m still looking.

#Procond Elettronica by Jim Cox on 2008-08-22 01:18

There is no resistor in R17 and JP1 and JP2 should be jumpered. What value do you have for R57?

#Procond Elettronica by brunner gerhard on 2008-09-10 06:51

please tell me for what application ist this part used?thank you

#Procond Elettronica by hackle berry fin on 2008-10-16 05:32

please!!can you help me fix my raphaie sw-x7i don\'t know the value of dz1 and r3(zener diode and resistor)thanks!!

#Procond Elettronica by Andy Bren on 2008-10-20 20:57

I am an electronics tech and I am attempting to repair this MC-70 controller board. Do you have schematics on .pdf you could email me? I would sure appreciate it.Also I noticed you are hiring. Perhaps I could do some work for you on the West coast. I tried calling the number but I only got a busy to...
Show More

#Procond Elettronica by lou broder on 2008-10-25 19:53

i am getting error message 21. any clue on what is wrong?

#Procond Elettronica by Jimmy Paragh on 2008-11-10 09:10

Hello , i am looking for a washing machine Electronic part, please let me know the prize and how to get it as quick as possible? Procond Elettronica Type Procond 451513003 Type E.Z 132120000 SW Ver. W1D00109 07/03

#Procond Elettronica by Jimmy Paragh on 2008-11-11 12:02

Hello , please send me the prize of the controll board Procond Electtronica Type Procond 451513003 Type E.Z. 132120000 SW Ver. W1D00109 07/03 I have been around to ask on several places here in Holland and found that the prize that i have to pay here is so high that if you put a € 100 on top of the ...
Show More

#Procond Elettronica by heri on 2008-11-21 04:54

Procon Elettronica 411514410 SH.047.p.F(x2)+0.68M2x0.00. p.F (Y2)+2x0.5mH250V 50/60 Hz-16A/40\'CHMF 25/100/21EN.133200

#Procond Elettronica by sanjay on 2008-11-21 22:35

R57 resistance value is 1k ohms wire wound around 5watts. presently i am looking for the value of R68. can you help?sanjay

#Procond Elettronica by Andrew Walford on 2008-12-08 19:30

Hi can you gve me a price for the above, cheers

#Procond Elettronica by Dusan Andjelkovic on 2009-01-02 15:23

Hello! I am from Serbia, and I need the board GE Procond Elettronica Type P. 451510051 F: 4290 Type E. 12430392/5 SW Ver. W2C01250 . I was wondering if there is a shop in Serbia, so I can buy it from here, and if you don\'t have a shop there, is there any chance of ordering it from my country, by th...
Show More

#Procond Elettronica by John Kennedy on 2009-01-05 01:04

My 10.6QI just stopped-no warning. When I start it it it makes a mild thumping sound- The display works ok. I want to fix it

#Procond Elettronica by FRANCESCO PARI on 2009-01-14 10:21

Dear Sir In my Ariston dishwasher LSI 41, we have the printed circut, typ: GE Precond Elettronica 356084601. My question is, if i can SEND YOU THIS CIRCUIT TO A CONTROL, CAUSE I DON\'T KNOW IF IT WORKS OR NO, AND HOW MUCH IT COSTS THE CONSIGNMENT + THE JOBWith regardsFRANCESCO

#Procond Elettronica by Edy Gerah on 2009-01-17 22:16

> Dear Sir/Madem,>>> I would like to asking you about your product sale .> I\'m looking for the HP 62A .New or other stocks .> Do you sale them ? Can I reguest order to you and internasional delivery> order to Singapore .> Because I have small business/personal.> Hope we c...
Show More

#Procond Elettronica by Mike Stalzer on 2009-01-29 20:55

Have the same problem. Proform treadmill. DZ4 burned out.Have been trying to get what the DZ4 diode was. Hope you got it right and Thanks for the info

#Procond Elettronica by freddy on 2009-01-30 03:07

Tengo problema con mi treadmill. aparece en la pantalla E2 lo que no permite que funcione mi treamill. Que debo hacer, por favcor ayudenme.gracias. espero su respuesta

#Procond Elettronica by freddy on 2009-01-30 03:11

Tengo un treadmill Image 10.6Q, aparece en la pantalla E2. y no funciona mi treadmill. que debo hacer. por favor ayudenme. gracias

#Procond Elettronica by Velazquez on 2009-02-05 19:54

I have some problems with my dishwasher Ariston LSI 66A, it seems the elettronic control does not work 45650110.It\'s possible to buy it on line? How does it cost?

#Procond Elettronica by danno on 2009-02-23 13:36

Hi,Do you have a line filter made by Procond Elettronica # 411.10.5040this is in a Varian Turbo V 550 pump controller.

#Procond Elettronica by Moti on 2009-03-02 06:50

Wellcom! I have a burnt component ty1. I need the component no\' of this part.

#Procond Elettronica by Mirwanto on 2009-03-16 06:36

Dear Sir,My LUX washing machine, the CPU is not working properly, so the tachniciant replace them with the new one. the CPU written as below: GE Procond ElettronicaType P4515100093 F6495Type E.1234303983SW Ver.W2C01551 06/feb/04EWM2000 WMS WMV200APMMy question is can that CPU be repair. give me your...
Show More

#Procond Elettronica by Duncan Macaskill on 2009-03-21 18:21

Hello can u give me a price for part number 411122430 Procond Elettronica this is out fo a Bendix Washing machine

#Procond Elettronica by Orlando on 2009-04-28 17:53

i need schematic diagram for control board MC-70 AW P/n124438 or

#Procond Elettronica by Manuel on 2009-05-25 17:30

HelloIm also would like to test this my module, i don\'t know if it\'s working well Is it possible to have a schematic or technical datasheet of this module*******Waht is the cost for repair? What is the cost for a new one?GE Procond ElettronicaType P. 451510050Type E. 12430392/4SW Ver. W2C01202THAN...
Show More

#Procond Elettronica by hamed on 2009-06-17 10:29

Dear Sir, Mam,I have a treadmill icon health & fitness and it is damaged so I open the cover and see the board with this model MC-70 Aw.revPart #124438 damaged .I have a qouestion:Two parts of this board are damaged and I cant read the part number on them.so please let me know the parts number(d...
Show More

#Procond Elettronica by Gergõ Mészáros on 2009-06-25 09:24

HelloI would like to enquire the undermentioned washing machine from the available of a component and the data of technical:Procond Elettronika411 625 431kWith thanks :Gergõ

#Procond Elettronica by Howard Karloff on 2009-06-26 03:21

I have two broken Proform MC60 motor controllers. How much wouldit cost to fix them?

#Procond Elettronica by DOENLEN on 2009-07-05 09:32

BONJOUR,COULD YOU TELL ME THE PRICE FOR A NEW PART FOR A PROCOND ELETTRONICA PART NO 356066303-FOR SIEMENS REFRIGERATOR REF KI24L451FF/01?BEST REGARDSGUY DOENLEN

#Procond Elettronica by Gerald Harman on 2009-07-23 16:55

Please repair and tesT under load for satisfactory operation. Believe burn out at DZ1, dz4a, dz4b LOCATION ON BOARD.

#Procond Elettronica by ricard on 2009-09-07 12:00

HelloIm also would like to test this my module, i don\'t know if it\'s working well Is it possible to have a schematic or technical datasheet of this module*******What is the cost for a new one?GE Procond ElettronicaType P. 451510051Type E. 12430392/5SW Ver. W2C01250

#Procond Elettronica by feri setiawan on 2009-09-28 04:07

mesin cuci saya klo d nyalakan aliran listrik k mana2(semua body nyetrum).saya kasih tau service center nya daerah mana?

#Procond Elettronica by C Westerhof on 2009-10-15 17:16

manual ge procond 356092103

#Procond Elettronica by davor prizmic on 2009-11-03 10:34

To whom it may be concern!please advice me as soon as possible if any opportunity exist for buying356084601 Circuit Board for Ariston LSI62 dishwash machine.I will pay by bank or by amEX OR VISA.Pls give me some advice or help me in any way-pls include all charges for shipping.

#Procond Elettronica by DAVID MARSH on 2009-11-20 10:11

I have a new GE Procond Elettronica Type P. 451510085 F:5065Type E. 124303975 SW Ver. W2C01551Electrolux Part Number 1321226746This is a new part (never fitted however the box is a bit tatty) it cost well over £100, as the part is of no use to me, would you know where I could sell it for a nominal s...
Show More

#Procond Elettronica by SETIABUDI on 2009-11-24 15:23

Electronic Module for washing machineHelloI would like to test this module, i don\'t know if it\'s working wellIs it possible to have a schematic or technical datasheet of this moduleRef = Type Procon :451511360Type E.Z: 13200353/2SW ver USA0020515/00 T70THANKS A LOTBEST REGARDS

#Procond Elettronica by SETIABUDI on 2009-11-24 17:53

I would like to request a schematic or technical datasheet of Ref =Type Procon :451511360Type E.Z: 13200353/2SW ver USA0020515/00 T70THANKS A LOTBEST REGARDS

#Procond Elettronica by Ron Hopkins on 2010-01-06 18:16

What did you find the value of DZ1 to be?What about the value of R57, the long round tube resister that gets over heated.

#Procond Elettronica by PICARD alexandre on 2010-01-13 22:34

hello , I search this product please:PROCONDELETTRONICA413.2712.00.10ìFthank you

#Procond Elettronica by kevin on 2010-01-15 02:55

DEAR SIRS,COULD YOU TELL ME THE PRICE FOR A PROCOND ELETTRONICA PART NO. 411624430.MANY REGARDS KEVIN

#Procond Elettronica by john lotherington on 2010-02-03 02:49

hi i have a amana stainless steel side by side fridge freezer model XRSS687BB.IM AFTER A CIRCUIT BOARD new,reco,or mine tested onboard it has hv international 451011010 ..122544-01------------------------------------amfel V18.hex B590-------------------------------------------GE PROCOND ELETTRONICA ...
Show More

#Procond Elettronica by Rajni on 2010-02-04 02:57

How can I get circuit diagram with block for this circuit board?There are two large fuse type resistors or right hand side of board, what are they? Looks like they are burned. What are the reasons for this overheated ?

#Procond Elettronica by marc schmuck on 2010-03-29 16:20

Hello, can zou give me a price for follow boardType P. 451510050Type E. 12430392/4SW Ver. W2C01202ThanksbrMarc Schmuck

#Procond Elettronica by CHK AR CONDICIONADO LTDA on 2010-04-09 12:43

NEED BOARD MACHINE INSTALLED IN A CARRIER AIR CONDITIONER BRAND MODEL:GE ELECTRONIC PROCOND 356,068,908.YOU CAN DELIVER IN THE U.S. EVEN VIA FEDEX?OUR CUSTOMER WILL BE IN THE USA next week.PLS WAIT RETURN.CLÓVIS HIROSHI KUNII

#Procond Elettronica by Detlef Rinke on 2010-04-13 20:58

Hello,I am search with the condensator unit.as the delivery terms are for Germany?ThanksD.RinkeIn German:Hallo,ich such dieses besagte Kondensatoreinheit.Was für Lieferkonditionnen haben Sie für Deutschland?DankeD.Rinke

#Procond Elettronica by ramon on 2010-08-05 13:18

Hola, esta maquina con nº prod. 914602703-00 no hace el programa de secado, cuando acaba de lavar activa un relé gira el tambor unas vueltas y para, no llega tension al motor de secado ni a la resistencia.Sospechamos de la placa 451510238 type E.132156823, el Servicio Oficial ha dicho que no hay rec...
Show More

#Procond Elettronica by raffaele on 2010-08-16 01:33

am looking for the replacement or the value of the ptc 2 which as a no ptc x240 L025 or the diagram whith the value of the componentvery gratefull asap please

#Procond Elettronica by Anita Hadlow on 2010-08-30 11:23

Dear SirWe are looking for the above part for a servis 1500 Caress washing machine. could you please advise cost and availability.RegardsAnita Hadlow

#Procond Elettronica by M. Boulmier olivier on 2010-08-30 21:51

Dear, I have a electronic card from a electrolux clothes washer , and i think it out of order.Part number : elettronica GE procond 12430381/6 356084806Could you test it and repair for witch prize ? Thanks for your feed back.Best RegardsO. Boulmier

#Procond Elettronica by Antonin on 2010-09-26 16:44

I have a Damamaged control board for the above washing machine. The procond type number is 3560 987 02.an other reference number is Ge Procond 451513144.I am trying to get information for this board.Can you help ?Thanks in advanceAntonin

#Procond Elettronica by PEDRO PABLO PRIETO MONZON on 2010-10-01 23:38

Tengo una cafetera de Nespresso el cual tiene dos tarjetas:Procond Electtronica #3560102109Procond Electtronica #3560102059Desearia informacion que me puede ayudar, ya que controla el cafe, pero no la leche.Espero que me ayude e informe de los costos por reparacion .

#Procond Elettronica by salvatore rassu on 2010-10-20 15:21

Hi,Got a zanussi jet system 1400 xc and i am looking for the electronic board 45151005112430381/5If you have this part ? How much with the shipping to the uk?Looking to speak to you.RegardsSalvatore

#Procond Elettronica by Elimir Iliev on 2010-11-15 19:38

Dear Mrs or MrI\'ve got serios problem! I use a washing machine electrolux but suddenly normaly work stop! I think microprocesor is out! Is it posible to purchace this part from you! Here is details:GE Procond ElectronicaType P. 451510133 F:6437Type E. 132156810SW Ver. W2C01450 50/02

#Procond Elettronica by lajcsi on 2010-11-23 13:27

please service manual

#Procond Elettronica by fraz ahmad on 2010-12-07 09:26

Hihow are you, hope you are doing very well. i have this part at home, the problem is this some z are burned-out. . ..and i cant figure what the exact , voltages and watts of these ZsDZ2,DZ3, DZ4 and D10i have rough guess abt these parts, like DZ2 and Dz3 = 24V 1 wattplease reply. . . . and tell me ...
Show More

#Procond Elettronica by fraz ahmad on 2010-12-07 09:32

please i have this part MC 70 Part #124438. . . .. please some can tell me the exact values of these locations DZ3 or DZ1, DZ2,DZ4,D10,D11. . . . . please reply. . then i could repair my Treadmill . . .

#Procond Elettronica by Peter Hancock on 2010-12-18 19:07

Hi,Please quote your repair, exchange or refurbished unit prices for Procond Elettronica controller PN 141877 used in a Proform 830 treadmill.Thanks,Peter

#Procond Elettronica by mr D A Wilkinson on 2011-01-07 16:52

is it possible to find repacement control board for our frigefreezer Number on existing is 452702001 thankyou

#Procond Elettronica by fabiana di porto on 2011-01-13 16:48

It seems that the Precond Elettronica 356084601 circuit of my Ariston LS 41 dishwasher is broken.Is it possible to buy a new one?How much would it cost?Thank youFabiana

#Procond Elettronica by Andrea on 2011-02-03 07:27

Buon giorno, sono nella necessità di reperire la sche elettronica della lavastoviglie Indesit che monta la scheda --GE PROCOND ELETTRONICA 356084601--- sull\'adesivo, oltre alla scritta procond elettrronica c\'è scritto: 23/01 ed i seguenti numeri: 452650801 21004683801avrei una certa urgenza di sap...
Show More

#Procond Elettronica by Frank on 2011-02-06 07:06

Does anyone know where I can get the circuit diagram for Procond Elettronica board n. 3560033089 or at least the value of RV8?Many thanks

#Procond Elettronica by John McGeady on 2011-03-09 22:12

think we need a new transformer, which has procond eletrrronica written on itcan you assist ?

#Procond Elettronica by Mark on 2011-03-15 14:30

Hello,I am search with the condensator HMF 25/100/21C unit.as the delivery terms are for Germany?ThanksBernd Mark

#Procond Elettronica by EL FETOUHI on 2011-03-19 16:35

bonjour, je cherhe le module BOCOND ELECTTRONICA 3560033089POUR LA CAFETIERE DELONGHI MAGNIFICA MERCI

#Procond Elettronica by DIEHL on 2011-03-29 10:45

Hello,Could you tell me the price for the Procond Elettronica Part no 3560061009 ( V16 ) for a refrigerator Vedette RC306.I only need the electronical cartBest RegardsMr DIEHL

#Procond Elettronica by SCHROETTER on 2011-04-01 16:10

Hello,Could you tell me the price for the Procond Elettronica Part no 3560066303 for a congelator SIEMENS .I only need the electronical cart .I am also ready to do a standard exchange if possible . Best RegardsMr SCHROETTER

#Procond Elettronica by Ben Hinx on 2011-04-21 10:10

Is it possible to purchase the control unit for an AEG Oko Lavamat 72630 update:GE Procond Elettronicatype P - 451510051 F:4875Type E - 12430392/5SW Ver - W2C01250 26/00

#Procond Elettronica by Jiri Kastura on 2011-05-01 16:52

Please, I need schematic electronic board for refrigerator Brandt CE 3220Xnumber bord is M1-A/B C15350940

#Procond Elettronica by Javier mendoza on 2011-05-02 23:15

Dear SirsNeed for technical information on the MC-70 card and power supply, I need relates to electronic card or not responding at start up.Very grateful for your attentionJavier mendoza..

#Procond Elettronica by marco azevedo on 2011-05-11 10:42

hi all. if possible give us a schema of procond electronica bord 35600a1139 of washing machine from electrolux ewf 1035 models.all regraetsMarco azevedo

#Procond Elettronica by Richard Montalvo on 2011-05-11 15:54

I need DZ1 and DZ24 diodes. Both appear to be burned. Can I repair them? Thanks.

#Procond Elettronica by villain on 2011-05-17 07:30

Cherche module Brandt C 3220X/1

#Procond Elettronica by MALIK RIAZ on 2011-05-18 08:18

I HAVE MC-70 MOTOR CONTROLLER CARD, PLEAS I WANT TO KNOW SOME PARTS VALUES OF THESE LOCATION ,R57,DZ1,DZ4 ITS BURNED WITH OVER VOLTS

#Procond Elettronica by Dimitris Poulis on 2011-05-18 13:03

i have problems with my electronic board is it possible for you to repair it or replace it and how is the cost? if this is possible please inform me about the way to send you my electronic board and the payment method.type P: 451510051 F: 5100type E: 12430392/5SW Ver. W2C01250 21/00

#Procond Elettronica by Ian thomas on 2011-05-19 18:02

Please could I purchase this part number from you 411312431How much Thanks Ian

#Procond Elettronica by Enrique Arturo Macias Acevedo on 2011-06-02 23:06

Me gustaria tener el diagrama electrico de su tarjeta con numero de parte 124438. Es posible conseguirla?

#Procond Elettronica by Mike Holzbauer on 2011-07-02 15:37

How much will it cost to get my circuit board repaired? Where can I send it, how long will it take?

#Procond Elettronica by geoff hards on 2011-07-17 17:00

I have a faulty control board for AEG L74810. The resistor R82 has burnt out. I wish to replace it but I do not know it\'s value. Please can you send me the value and a schematic please?Thank you for your help.Geoff Hards

#Procond Elettronica by Ron Ledwell on 2011-07-29 17:27

NTE Part #\'s NTE145A and NTE5137A (about $2 each at a local Electronis Suppy Store. Fixed my Problem.

#Procond Elettronica by Jozsef Domonyik on 2011-08-09 17:38

HelloIs it possible to have a schematic or technical datasheet of this moduleProcond Elettronica 3560132009Thanks Jozsef

#Procond Elettronica by Guenat on 2011-08-22 14:52

Bonjour je recherche le module Procond elettronica 3560089039 pour un lave vaisselle FAGOR et le prixMerci

#Procond Elettronica by schepers didier on 2011-08-24 12:31

My module for aeg lavamat 72800 /ge procond type p 451515351-e 132219810,version W1a 30106 19 apr 04.give me please the price to repair or to exchange my module ,en how to proceed.thanks

#Procond Elettronica by Traverso Gian Piero on 2011-09-06 08:34

Ronco Scrivia, 06/09/2011Vi sarei grato se poteste inviarmi preventivo di spesa ed eventuale indirizzo di spedizione per la riparazione della scheda in oggetto.Ringrazio anticipatamente.Gian Piero Traverso

#Procond Elettronica by sunil de silva on 2011-09-08 18:11

I have Zanussi Washing machine SWF1440W, which has Procond 451517403PCB. I want to test this PCB as the washing machine does not work. It turns on and nothing happens. Please send me a quote or if you have this part for sale, please let me know the price.Thanks

#Procond Elettronica by Tim Dong on 2011-09-11 15:51

I am in need of the schematic for MC-70 AW.Rev -, Motor Control, P/N: 124438. Apprearantly, Zener diode, DZ1 and diode D10 were damaged. Does anyone know where I can get it? Thank you very much.Best Regards,Tim Dong

#Procond Elettronica by schepers.didier@gmail.com on 2011-10-07 06:32

module doesnt work,no output

#Procond Elettronica by Tim Cumings on 2011-10-23 22:15

I have an error code e21 on my treadmill. I found that the speed sensor wire was broken off the screw on the motor attachment. Do you have one and how much is the cost. Thanks

#Procond Elettronica by Kazmarcik on 2011-10-25 17:32

Ich benötige eine neue Elektronik

#Procond Elettronica by k burnett on 2011-10-27 10:28

is the following availiableAEG circuit board for arctic upright freezer

#Procond Elettronica by Thomas Riis on 2011-11-18 07:29

Hi,We have a defect controller board : \"3560144009\" from Procond Elettronica.It fails by periodically stops the motor and heating elements. It seems that the ignition for the motor is unstable. For me it sounds like it is a moped / motorcycle with a bad ignition :-)Please could you infor...
Show More

#Procond Elettronica by ADNAN HRNJIC on 2011-11-23 21:31

Hello,I would like to order part no.411312431 and how much it cost

#Procond Elettronica by ruwinda sa on 2011-11-30 04:36

dir : mr ple give me a ELETTONIC CRD [ 3560 041 10 a] 0030-0013c cirkite diagram mr: Ruwinda E/N hotel blue woter sri lanka

#Procond Elettronica by ian pierce on 2011-12-03 11:25

have you got one of these and how much please many thanks i pierce

#Procond Elettronica by Bernd on 2011-12-06 20:42

Would anyone be so kind and send me an circuit diagram for Procond Elettronica board n. 3560033089 many thanksBernd

#Procond Elettronica by Johann Ogmundsson on 2011-12-15 23:04

I\'m dealing with problems in this machine . It is hard to start programs and when it start the machine run for several minutes and is working constantlywhen it has 51 minutes to remaining of the program. I think it is something wrong with Circuit-board Type P 451510069 F371. Please comment if it ri...
Show More

#Procond Elettronica by Lee Birloton on 2011-12-27 20:14

PLS price for Procond Elettronicatype:P451525507 F:3711Type: E132219814SW VER.W1a30140 07/dec/05Thanks for help L.Birloton

#Procond Elettronica by Lee Birloton on 2011-12-27 20:15

PLS price for Procond Elettronicatype:P451525507 F:3711Type: E132219814SW VER.W1a30140 07/dec/05Thanks for help L.Birloton

#Procond Elettronica by david conley on 2011-12-30 23:42

AEC Electrolux fridge freezer circuit board has burnt out part no GE ITA:452707180 sw NFBFOA24 :20/054225. can you advise cost of replacement and delivery time please.

#Procond Elettronica by Pavel Zima on 2012-01-10 12:52

HelloIs it possible to have a schematic or technical datasheet of this moduleProcond Elettronica 3560132009 Pavel Zima

#Procond Elettronica by Pavel Zima on 2012-01-10 12:52

HelloIs it possible to have a schematic or technical datasheet of this moduleProcond Elettronica 3560132009 Pavel Zima

#Procond Elettronica by angel on 2012-01-17 03:14

do you need the part #? dz1 is a zener 15v dz4a and b id zener 12v the d10 is a regular recti 1n4148

#Procond Elettronica by George Bellamy on 2012-02-01 14:21

Can I purchase SW1 push switch for the Procond Electronica 356084601 LED mudule ?

#Procond Elettronica by joel on 2012-02-05 11:13

Bonjour je recherche un condensateur procond electronica zem411 13 22 038 OU S H 0.1µF (X2)+2x 0.015µF (Y) +2.2M om250V~ HPF 25/Q85/21RB 24 565-1Cette piece viens d\'une cuisiniére rosière trio ( plaque four lave vaisselle )merci

#Procond Elettronica by Dieter Pauwels on 2012-02-28 18:08

Hello GeoffI have the exact same problem. Did you find the answer?Yhx

#Procond Elettronica by Dieter Pauwels on 2012-02-28 18:08

Hello GeoffI have the exact same problem. Did you find the answer?Thx

#Procond Elettronica by Antonio Sánchez Ortiz on 2012-03-01 17:22

Good afternoon, I`m looking for a module Procond Elettronica 3560089039 for a washdisher Fagor, and also the price.Thank you very much.

#Procond Elettronica by Antonio Sánchez Ortiz on 2012-03-01 17:27

Good afternoon, I`m looking for a module Procond Elettronica 3560089039 for a washdisher Fagor, and also the price.Thank you very much.

#Procond Elettronica by Barbara Anselmi on 2012-03-09 15:39

Dear Sir,the Procond Elettronica 356084601 circuit of my Ariston LSI 41 dishwasher is broken.Is it possible to buy a new one?How much would it cost?Thank you Barbara AnselmiSIENA-ITALY

#Procond Elettronica by suparjo on 2012-03-20 11:32

My LUX washing machine was in problem. According to the technision the CPU is not working properly. He remove the CPU but he did not sure.The CPU written as below:GE Procond ElettronicaType P451510093 F:6473Type E.124303983SW Ver.W2C01551 24/giu./05My questions are:1. Can that unit be repair2. if it...
Show More

#Procond Elettronica by Orukwo Amaechi on 2012-03-24 09:17

Please get me quote urgently for a Procond Ellectronica capacitor/switch of 0.25 micro farad with part no 411135901 for dish washing machine. We need it to replace the faulty one on our dish washing machine with the following specification:ELX Model: LS9PPN: 9CGX50502215EL: AC 400 V3 N AC 230V/3/50H...
Show More

#Procond Elettronica by Patrick séguy on 2012-04-14 12:34

Bonjour,je suis à la recherche d\'un condensateur réf : 411122430sh 0,047µF(X2)+0,68Mhome2X0,025µF(Y2)+2X1mH250 V~50/60Hz -10A/40°cHMF 25/100/21CEn avez-vous en stock?CordialementPatrick

#Procond Elettronica by patrick on 2012-04-18 17:19

This Procond elettronica is bad because no responces!!!

#Procond Elettronica by FRANCOIS on 2012-04-30 18:15

Bonjour,je suis à la recherche d\'un condensateur réf : 411.10.5060GMF 40/100/21sh 0,15µF(X2)+ 2x 0.004µF (Y)2X0,5 mH + 1.5 MQ250 V~ 50/60Hz -10A/40°c46-94CordialementFrancois

#Procond Elettronica by Gary Diamond on 2012-05-01 06:34

ARE YOU GUYS BUY USED BOARDS PULLED FROM TREADMILLSIF SO HOW MUCH NOT TESTED? OR REPAIRED, UNLESS YOU WANTED THEM REPAIRED

#Procond Elettronica by Sasa Todorovic on 2012-06-03 13:04

Hello,Is it possible to send me schematic datasheet for this module of washing machine Zanussi TurbodryProcond Elettronica 3 560 339 02Greetings,Sasa

#Procond Elettronica by gaga on 2012-06-22 13:09

Hi My Lux washing machine serial number is WM1007S20091200266, model WM1007S, pcb board code is 3013007A0008, I need pcb board, can you send me this part in georgia country?

#Procond Elettronica by Michele De Moja\' on 2012-07-11 07:10

My dishwasher Ariston LSI 61 E has broken down.Please How Much cost the board sended to Italy in Reggio Calabria.Thanks

#Procond Elettronica by Michael Cox on 2012-07-14 14:00

Hi there wonder if you can help me find and price, a pcb for a zanussi washing machine, FJS 1425w Prod no 914512721Serial no 10400034Type P6348639IPX4PleaseRegards mike

#Procond Elettronica by FERRATON on 2012-07-26 17:38

Bonjour Je recherche le module de procond elettronica 3560089039 Pour Un lave vaisselle FAGOR .pouvez-vous me communiquer le prix de cette pièce ?merci

#Procond Elettronica by Attila Tóth on 2012-08-22 07:01

Hi!I have an AEG Lavamat 74850 washing machine. On the control panel, in the power supply circuit the LNK305 off-line switcher IC and the fusible resistor has gone. I\'ve replaced them, but the resistor\'s value was not recogniseble and I did not have a circuit diagram and the hungarian service cent...
Show More

#Procond Elettronica by Marlene Duval on 2012-09-09 20:53

Would be glad if you couldt help me with a schematic diagram for my ESAM4200.Cod.Procond: 454010272Cod.De Longhi: 5232121200Wk: 49/08 Op:0043 SW:7.2For your effort many thks in advanceWith kind regardsMarleneDuval

#Procond Elettronica by tamgho kevin on 2012-09-13 08:08

j\'ai besoin de savoir combien coute cette carte

#Procond Elettronica by Joseph Buhagiar on 2012-09-30 14:51

I would like to enquire the cost of a repair or purchase of a new control card for an AEG lavamat silent system plus 74650. The number on the control card is Procond elettronica 3560132009.Thanks and regards,Joseph

#Procond Elettronica by Rohan Navaratnam on 2012-11-06 09:36

0203050000230Ge procond elettronicaProcond 452750010 M1B V1.0.3 1535-0940 18/05Hello there I need this product immediately to my fridge-freezer(make BRANDT)complete component print-plate - sectionhow much it cost totally to send it to Denmark?

#Procond Elettronica by Unzeitig Lubomír on 2012-11-12 16:07

Bonjour Dže recherche le modul de PROCOND elettronica 3560089039 Pour Un umývat vaisselle FAGOR. pouvez-vous me communiquer le prix de cette pièce? merci

#Procond Elettronica by Maliki herman on 2012-12-03 04:30

I need chasis mounted filter type efnf 3,in indonesia maybe semarang..please info to pay,tq

#Procond Elettronica by Ruben Sousa on 2012-12-15 21:17

Hi there.I want to ask if you have this part supply on stock?!The reference is 132400 / 413 26 005.If you do, just tell me how much is the price in total with shipping to Portugal.Thank you very much.

#Procond Elettronica by Jacques Erades on 2013-01-17 02:17

Would be glad if you couldt help me with a schematic diagram for my ESAM4200.Cod.Procond: 454010272Cod.De Longhi: 5232121200Wk: 49/08 Op:0043 SW:7.2For your effort many thks in advanceWith kind regardsJacques Erades

#Procond Elettronica by Charles Mataure on 2013-01-22 18:45

Please advise the value of this capacitor.

#Procond Elettronica by George Katinios on 2013-03-09 08:52

Dear Sirs,Is it possible to tell me the value of R82 resistor or send me the electronic schematics? Thank you in advance,Best wishesGeorge.

#Procond Elettronica by ronnie byrne on 2013-03-12 21:20

hi i am looking for card for zanussi zwn 1220w washing mc procond ecettronica type procond 451516703type assembly 132191513type e board 124307062sw vwr uda30202t70 wk 48/08

#Procond Elettronica by Zsohár Imre on 2013-03-30 16:21

Please help me!AEG LAVATHERM Dryer turns off after 10 seconds.PNC: 91601416300S / N: 34285616I do not know what is wrong!

#Procond Elettronica by bratialav on 2013-04-04 06:47

Please for electrical scheme my Esam 3500.THANK YOU...

#Procond Elettronica by Casella Vincenzo on 2013-04-05 22:57

Dear Sirs, I have a PROCOND ELETTRONICA card damaged.It is inside the yellow cover with these codesTYPE: 452604120COD ZANUSSI: 15248541/0220/240 Vac - 50 Hz T65 Ver. AWK 27/00The ELECTRONIC CARD inside damaged is marked:GE PROCOND ELETTRONICA 356084500The processor assembled on the card is marked SI...
Show More

#Procond Elettronica by Laszlo Dubai on 2013-04-16 20:19

I have a faulty control board for AEG L74810. The resistor R82 has burnt out. I wish to replace it but I do not know it\'s value. Please can you send me the value and a schematic please?Thank you for your help.

#Procond Elettronica by Emilio Utrilla on 2013-06-03 17:10

Hello, I need where to buy or repair a Procond elettronica 3560089039 module and the price.Its for an EDESA dishwasherThank you.Hallo,Bonjour je recherche le module Procond elettronica 3560089039 (neuf ou réparation du vieil) pour un lave vaisselle EDESA et le prixMerciHola,Estoy buscando un módulo ...
Show More

#Procond Elettronica by pericop1 on 2013-06-13 16:47

Hola Laszlo Dubai:R82 = 0 (fuse) Simply conductiveCan you help me? Please, I need value R91.Thank you in advance

#Procond Elettronica by Nickolay on 2013-06-27 06:21

Good day.Have you the power board for delonghi coffee machine cod DeLonghi 5232109600, cod Procond Elletronica 3560033089?How much cost and can you send this part for me?

#Procond Elettronica by mr m ibrar on 2013-11-18 12:09

The red light is all the time flashing, when the the compressor first comes on it stays on for good 5-10 min and goes to standby and then when it comes back on after a while it stays on for round about 3 min and there about . The supper freeze dose not come on as well, so i will be very great full i...
Show More

#Procond Elettronica by mr m ibrar on 2013-11-25 15:15

The red light is all the time flashing, when the the compressor first comes on it stays on for good 5-10 min and goes to standby and then when it comes back on after a while it stays on for round about 3 min and there about . The supper freeze dose not come on as well, so i will be very great full i...
Show More

#Procond Elettronica by REALI on 2014-11-17 18:25

I HAVE AN ARTHUR MARTIN ELECTROLUX WASHING MACHINE AND THE ELECTRONIC CARD HAS TAKEN WATER AND IT BURNED OUT. i WANTED TO KNOW WHETHER YOU COULD REPAIR IT OR EXCHANGE IT.CAN YOU GIVE YOUR PRICE FOR IT.i give you the references:prod number:91451270400type p:451510050F:4875Type E: 12430392/4SW ver. W2...
Show More

#Procond Elettronica by Lucien Huble on 2015-03-08 11:13

I have a faulty control board for EWF 1620 The resistor R82 has burnt out. I wish to replace it but I do not know it\'s value. Please can you send me the value and a schematic please? Thank you for your help.

#Procond Elettronica by brusselle on 2015-06-21 10:48

Hello, I need where to buy or repair a Procond elettronica 3560089039 module and the price.

#Procond Elettronica by Roberto Filippelli on 2015-09-18 17:59

I have a faulty board for the aeg 64811.pcb inside : 3560041139.Component D11 is broken, can you tell me the type please.

#Procond Elettronica by Tamadite on 2015-11-04 22:02

Can you please give me the value of component C34 of PCB Procond 3560144029?

#Procond Elettronica by Tamadite on 2015-11-04 22:29

Can you please give me the value of component C34 of PCB Procond 3560144029?

#Procond Elettronica by Tamadite on 2015-11-04 23:05

Can you please give me the value of component C34 of PCB Procond 3560144029?

#Procond Elettronica by Chansac on 2016-03-03 16:41

BonjourJe recherche le schéma pour une platine Procond électronica 356O1029 montée sur un réfrigérateur Brandt 1153HBien à vous

#Procond Elettronica by Muhammad usman on 2016-07-26 10:01

Dear Sir,Please helpot me hoe i repair this controller , its burnt due to 220V ,or please send me its technical data sheet where i can fix it Thanks

#Procond Elettronica by Jørgen Toft-Petersen on 2017-04-22 09:08

HI ThereI need a schematic over the above PCB. It is siiting in a Atlas NFS242 frezer

#Procond Elettronica by amin moradi on 2017-06-01 23:37

HiI need schematic of this board Procond Elettronica 3560101029thanks

#Procond Elettronica by amin moradi on 2017-06-01 23:41

HI Please attach any schematics, hook-up diagrams, or manuals you may have.

#Procond Elettronica by Greg on 2017-06-08 07:30

Hellol Need schematic for procond elettronika 3560144029 or information about ferrite transformer (voltage winding or equivalent resistance)thank you

#Procond Elettronica by gerardo aldape salas on 2017-06-21 16:29

i need repair a module 170-0518 rev.2 im live in mexico

#Procond Elettronica by aleks on 2017-06-25 19:47

Circuit Diagram procond elettronica 3560033089. R68 - ?????

#Procond Elettronica by Quy P Nguyen on 2018-01-03 14:10

Procond 451523906

#Procond Elettronica by Brunet on 2018-01-04 09:08

HelloIs it possible to have a schematic or technical datasheet of this moduleProcond Elettronica 3560132009Thanks Martial Brunet

#Procond Elettronica by RaymondMop on 2018-09-05 04:19

Hello. We invite you to the placement of video from yon the world. Online for Adults

#Procond Elettronica by julien on 2018-10-27 12:59

I need to replace (or repair) the electeonic card of my dryer Faure. The Start button donnot work any more.Thanks,Michel Julien

#Procond Elettronica by JUGIE on 2019-02-05 19:38

HiI need schematic of this board Procond Elettronica 3560101029thanks

#Procond Elettronica by Rune Møller Hauser on 2019-04-03 20:01

Print number: 3560101029Is mounted in Brandt refrigeratorNormal function in about 8 years, then it start writiing "e" in display, and start bipping. Then I turn the temperature up and down, and then it have normal function again, maybe in 1 hour, sometimes 14 days I think its a´fai...
Show More

#Procond Elettronica by Knud Oellgaard on 2019-04-25 20:13

HiWhere can I get a new electronic thermostat print to my Atlas NFS242

#Procond Elettronica by HURTADO Alain on 2019-05-09 15:31

Bonjour je cherche une carte GE Pocond ElecttronicaType P. 451510133 F : 6154Type E. 132156810SW Ver. W2C01450. 50/02Pourriez-vous m'indiquer comment puis- je en acheter une ou faire réparer la mienne ?

#Procond Elettronica by Hassan Sulaiman on 2019-07-30 05:47

Hello,I ve this Procond Elettronica card part no: 12430381/5 356084806 of which its functionality is suspect. How can I get it tested/repair and what's the likely cost if I send it across to you for test/repair?Plse reply via email.Best rgds.

#Procond Elettronica by M.Beatriz Silveira MD on 2019-08-11 16:08

procono electtronica part 413 26 016I need this part to fix a machine

#Procond Elettronica by Ignasi López on 2019-12-10 07:35

My fridge don't work correctly. Continuesly put a message with E and whistle.The tecnic said me that that isn t a water problem, and he prove the motor and it works good.He said that the problem is is electronic system.I can t find a new electronic base.This base looks good and I m not sure...
Show More

#Procond Elettronica by Jaypet on 2020-03-12 20:04

Electrical installation in Kazan

#Procond Elettronica by catalin on 2020-05-30 11:38

how much would a spare part Procond Elettronica411612438 costs? thanks

#Procond Elettronica by Niels Sylvest on 2020-09-04 14:35

I have a printcard it is mounted in AEG Electrolux Lavatherm TN95670is it possible to repair, so that machine can be used again, there is no light in the panel at all, and the repair man told me that the failure is in the computer/print.please inform me adress for repair of the card in Denmark

#Procond Elettronica by Essak on 2020-09-16 11:38

I have circuit board and R82 resistor blown. How can I repair it? Where to get replacement part. How can I find exact value of resistor? Is it 0.82 ohms or 820 ohms. Please reply soon. I live in Leicester, the U.K. Thank you.

#Procond Elettronica by Hassaan on 2020-12-12 05:05

Dear sirPlease provide me the electrical diagrammatic of wohlenberg 115 1984 Thanks

#Procond Elettronica by Arvi Raud on 2021-10-07 16:50

Hi, I need a display on the Fagor refrigerator 07-0992440circuit board barcode180809506006manufacturerProcond Elettronica

#Procond Elettronica by Flashpaqmzt on 2021-11-18 14:10

elements (case, binding).

#Procond Elettronica by WILDKATcck on 2021-11-18 20:28

A handwritten book is a book

#Procond Elettronica by Telecasterkds on 2021-11-20 12:32

only a few survived.

#Procond Elettronica by WILDKATpvt on 2021-11-22 10:41

Europe, and in Ancient Russia

#Procond Elettronica by Herberttep on 2021-11-25 06:17

economic crisis in pakistan essay 2020

#Procond Elettronica by Telecasterduv on 2021-11-30 03:37

reproduced by hand, in contrast

#Procond Elettronica by Juicerxnh on 2021-12-02 03:52

Libraries of the Carolingian era). IN

#Procond Elettronica by kellyTag on 2021-12-09 02:09

hello. topic for me thanks kelly

#Procond Elettronica by Visionouv on 2021-12-10 22:38

drafts of literary works

#Procond Elettronica by kellyTag on 2021-12-15 04:05

hello. topic for me thanks kelly

#Procond Elettronica by kellyTag on 2021-12-29 15:17

hello. topic for me thanks kelly

#Procond Elettronica by RainMachinexqn on 2022-01-02 10:47

"Julia's Garland" (fr. Guirlande de Julie)

#Procond Elettronica by KrisstiGreed on 2022-01-02 20:29

Two girls have no place to celebrate the new year, who will invite us? copy link past browser and write me twi.kz/K5Wl

#Procond Elettronica by Holographiccjr on 2022-01-03 08:52

multiplies (see also article

#Procond Elettronica by GiBlobado on 2022-01-03 11:17

kwatery augustow www.noclegi-pracownicze-augustow.online stx21

#Procond Elettronica by ThomasFum on 2022-01-04 10:17

An firm intimate property and greatly ready treatment in behalf of Covid would be a significant breakthrough as a remedy for managing the pandemic, but two antivirals recently authorized in the US explore up with some eloquent caveats, including ungentlemanlike gear up and incident single to each th...
Show More

#Procond Elettronica by Pouringjyy on 2022-01-11 08:42

Middle Ages as in Western

#Procond Elettronica by Josephfug on 2022-01-12 00:21

I just want to say thank you for this great forum. I found a solution here on computer-cnc-repair.info for my issue.

#Procond Elettronica by Gisenobby on 2022-01-19 06:19

noclegi augustow bon turystyczny noclegi pracownicze augustow w augustowie www.noclegi-pracownicze-augustow.online stx21

#Procond Elettronica by Vitamixxfp on 2022-01-20 00:51

secular brotherhoods of scribes.

#Procond Elettronica by Blenderdwt on 2022-01-23 04:42

Of his works, he is especially famous

#Procond Elettronica by CHIRPpdm on 2022-01-27 01:09

antiquities. These are the Egyptian papyri

#Procond Elettronica by RainMachinezda on 2022-02-06 00:31

(palimpsests). In the XIII-XV centuries in

#Procond Elettronica by Raymondskype on 2022-02-20 05:12

Gdzie postrzega? celuloidy a seriale online – pochwalane architektury streamingowe Celuloidy plus seriale online ostatnie gwa?tem konsekwentny fragment modnej rekreacje. Kontrahenci nagminnie zabiegaj? najcudowniejszych tezy do przewertowania w odpoczynek, zmrokiem akceptuj w linii. Masowy przekrój ...
Show More

#Procond Elettronica by Garminzwfm on 2022-02-23 00:26

ancient and medieval Latin,

#Procond Elettronica by Glassuth on 2022-02-27 02:48

At the same time, many antique

#Procond Elettronica by Squierpzr on 2022-03-02 00:54

inventions of typography

#Procond Elettronica by Herbert2Caure on 2022-03-02 08:27

Are you an American who is upon looking notwithstanding exigency loans ? Do you think you clout need to drift compete for a accommodation soon? Are you on tap to drop of engaging normal loans that appear along with a tombola of hassle? Whatever your setting is, we are here to skedaddle! We be underg...
Show More

#Procond Elettronica by WILDKATmln on 2022-03-07 20:36

manuscripts held onto

#Procond Elettronica by Independentmgc on 2022-03-12 06:19

or their samples written

#Procond Elettronica by PatrickvoB on 2022-05-19 20:44

An injury that renders a person handicapped and prohibits them from returning to work for a lengthy period of time is known as a long-term disability. Long-term disability lawyers in Brampton can offer you peace of mind and support during this difficult time.

#Procond Elettronica by Jasondow on 2022-06-04 15:08

Republican politicians all over the country have repeated the Great Replacement theory A century-old racist theory reentered the political discourse around immigration and has become commonplace on the campaign trail as Republicans hope to retake control of Congress in November.

#Procond Elettronica by meext on 2022-06-07 03:04

SWWiuxREMgBB4MS6wlttlQTFCSHIyC7SKf79pv1TtrKZMgmiUTMQCxZgSIyG6TLDt3BoAYjgAkvACRirj8ALSaw94G9ujkTFL9T1iqS0GSx25fcW4n62EXi6hobmMJxHaKJxnHMzNQ4BB14MGkP8Qb9isVXJ2HsI

#Procond Elettronica by pooDug on 2022-06-11 09:37

hallo ich bin POO :P ich wohne in IR. Das ist wohl thema? hmmmm , best regards for all :) POO I need to use eng or can GER?

#Procond Elettronica by Daviddoody on 2022-06-16 03:18

A large amount of people looking for a new job are unsure expediting veteran resume services constitutes a solid investment and this is a excellent puzzle, so we ought to first take a look at some of the every-day finishes that Commenced with executives that make the contract and use a on-the-ball r...
Show More

#Procond Elettronica by Tom on 2025-04-16 23:53

seeking repair service for my Procond Elettronica MC-70

Contact Us

🚑Shop Location🛠️

Industrial Electronic Repair
145 Rockwell Place Ct
Tobaccoville, NC 27050
🚑 Rush repair shipments only — no walk-ins.

📞Phone

📦Mailing Address🚛

Industrial Electronic Repair
931-E S. Main St #204
Kernersville, NC 27284
📦 Mailing Address (for invoices or shipped repairs)
No walk-ins accepted.