Sanyo Denki Service & Repair Forum

Sir,i am using sanmotion TS1-AA2AA for sanmotion servo motor.this a fully programmable drive.the main problem i am facing with this one is iam enabling the servo on function any time.but the servois not switched means 140v to the drive is not going.please tell me the solution,regardsSreekanth reddy.C

— Posted by sreekanth reddy on 2008-08-26

Reply🗨️Ask a New Question Below❓

If you need your Sanyo Denki unit tested or repaired,
give us a call at 1-336-969-0110.
We offer fair estimates and extended warranties on the work performed.
Shipping/Receiving:
Industrial Electronic Repair
145 Rockwell Place Ct
Tobaccoville, NC 27050
Phone: 1-336-969-0110

Recent 6 Comments

#Sanyo Denki by santosh kumar chauhan on 2007-01-09 12:03
Dear sir I am using PM driver (sanyo denki PMM-MD-23120-10) for stepper motor (sanyo denki 103H71121-0410). As I selected pulse/direction mode the motor runs in CW direction only when I down the direction pin low. The output of PC4 is high when its input is low. what is wrong with PM driver ?rgdsSan...
Show More
➡️ Reply
#Sanyo Denki by sreekanth reddy on 2008-08-26 07:49
Sir,i am using sanmotion TS1-AA2AA for sanmotion servo motor.this a fully programmable drive.the main problem i am facing with this one is iam enabling the servo on function any time.but the servois not switched means 140v to the drive is not going.please tell me the solution,regardsSreekanth reddy....
Show More
➡️ Reply
#Sanyo Denki by sankar on 2009-04-24 13:09
sir,our cnc m/c brother tcs2a table axis servomotor (sanyo denki) having position shifting error is facing because of encode got detororated due to coolant entry. is it possibe to change the encoder , if it is possible please guide me.thanks&regardss.sankar
➡️ Reply
#Sanyo Denki by Nir Ben-Hur on 2009-05-31 08:37
Hi,I have few (around 5) PM Driver (Model: PMAPA1A6B20) units that failed while used at TEL Prober Machine. The part age is 3-4 years.Usually the problem reflects as noisy motor and motion followed by encoder errors. What will the common repair cost for that?Best regardsNir Ben-hur972-54-3339535
➡️ Reply
#Sanyo Denki by Arpit Bhatnagar on 2010-08-28 07:14
We have one equipment in which sanmotion motor is used for motion and now gone bad. we want to repair this motor. Symptoms:- Armature jam, Tight in motion.Model no:- Q1AA06040DXS24MMake:-Sanyo Denki.Please reply soon.
➡️ Reply
#Sanyo Denki by SRIKANTH R on 2011-03-03 11:01
we have amplifier sanyo denki make1.60BA100FFW0H2.60BA030FXW0T3.60BA030FXW0PPLEASE HELP US IN GETTING CONNECTING MANUALSREPLY SOON
➡️ Reply

Contact Us

🚑Shop Location🛠️

Industrial Electronic Repair
145 Rockwell Place Ct
Tobaccoville, NC 27050
🚑 Rush repair shipments only — no walk-ins.

📞Phone

1-336-969-0110

📦Mailing Address🚛

Industrial Electronic Repair
931-E S. Main St #204
Kernersville, NC 27284
📦 Mailing Address (for invoices or shipped repairs)
No walk-ins accepted.