Sitra Automazione Service & Repair Forum

Spindle drive VSH tipo vsh6 01VSH6356 I have a problem with this drive and hope you can help me.The display shows L20 and also the cnc control says the drive is not ready.Could you tell me if i could get the manual for this drive that would list all the alarms. Thank You Jim Aarssen email ak2maintenance1@aarkel.com

— Posted by Jim Aarssen on 2008-09-23

Reply🗨️Ask a New Question Below❓

If you need your Sitra Automazione unit tested or repaired,
give us a call at 1-336-969-0110.
We offer fair estimates and extended warranties on the work performed.
Shipping/Receiving:
Industrial Electronic Repair
145 Rockwell Place Ct
Tobaccoville, NC 27050
Phone: 1-336-969-0110

Recent 8 Comments

#Sitra Automazione by Mike Haverkamp on 2006-01-14 17:54
Sitra Automazione VSD 6Drive is showing a L 08 on the digital display before we try to start the spindle. When we try to start the spindle the drive shuts off & goes black. Any suggestions? I need help, my milling machine is down & I have work backed up for it.Thank you for your attention to...
Show More
➡️ Reply
#Sitra Automazione by Dmitry Vernikovsky on 2006-02-21 18:34
May by it is very late-on my instruction the L08 it is undervoltage. You must check input rectifier .
➡️ Reply
#Sitra Automazione by Pete Gallagher on 2007-09-20 09:29
The above drive is fitted to a Mecof 5 axis milling machine and controls the high speed finishing head.This is the 2nd occasion that the 4 large capacitors, thyristors, power resistors and varistors on the input side of the drive have failed (exploded), welding the main contactor closed blowing 125 ...
Show More
➡️ Reply
#Sitra Automazione by Jim Aarssen on 2008-09-23 16:48
Spindle drive VSH tipo vsh6 01VSH6356 I have a problem with this drive and hope you can help me.The display shows L20 and also the cnc control says the drive is not ready.Could you tell me if i could get the manual for this drive that would list all the alarms. Thank You Jim Aarssen email ak2mainten...
Show More
➡️ Reply
#Sitra Automazione by R S Raghavan on 2012-02-02 11:50
Dear Sir,We have one new CP 800 converter with us. On trying to install this unit we found the parameters were missing in the system. When we tried uploading the parameters through the serial interface of the CP 800 we found the system had no firm ware loaded. Can you please send us the firmware 1-9...
Show More
➡️ Reply
#Sitra Automazione by Krzysztof Pachucki on 2012-05-09 19:40
Hello,we need list of errors on Sitra HF converter model CP 800. Can you please send usBest RegardsKrzysztof PachuckiMaintenance EngineerTel: +48 33 499 3731Mobile: 0 785 009 517Fax: +48 33 499 3501PachuckiKrzysztof@eaton.comwww.eaton.comVehicle Group EMEAEaton Automotive Systems Sp. z o.o.Ul. Rudaw...
Show More
➡️ Reply
#Sitra Automazione by Carlos Melo on 2019-10-07 09:39
I´m repairing a VSD6 ampli-spindle witch have a problem in brake system.There are two resistances R3 and R4 that I don´t know the value. Can you help me?Ampli-spindle: Sitra VSD 6 sn: 98VSD6252PCB of brake: Sitra 1993-FR.Thanks in advance.Melo
➡️ Reply
#Sitra Automazione by Genesis mold on 2021-09-24 19:41
Digit 165 with C1 control that is giving me a PL2317 " VSD Inverter Error 03 - Desaturation " ? Any direction would be helpful and appreciated
➡️ Reply

Contact Us

🚑Shop Location🛠️

Industrial Electronic Repair
145 Rockwell Place Ct
Tobaccoville, NC 27050
🚑 Rush repair shipments only — no walk-ins.

📞Phone

1-336-969-0110

📦Mailing Address🚛

Industrial Electronic Repair
931-E S. Main St #204
Kernersville, NC 27284
📦 Mailing Address (for invoices or shipped repairs)
No walk-ins accepted.