Anilam for Service call 1-336-969-0110 at Industrial Electronics Repair

Anilam Service & Repair Forum

Hi john I called you earlier about connectors for servo driver card. We had cmos setting problems and fixed them on the 1100 by replacing the cpu board bios chip which contains internal batteries. We can walk you throughit if you need help. Interesting how your post about this problem poppedup in front of me while looking for more info on the 1100.

— Posted by steve wood on 2010-04-02

Reply🗨️Ask a New Question Below❓

If you need your Anilam unit tested or repaired,
give us a call at 1-336-969-0110.
We offer fair estimates and extended warranties on the work performed.
Shipping/Receiving:
Industrial Electronic Repair
145 Rockwell Place Ct
Tobaccoville, NC 27050
Phone: 1-336-969-0110

Recent 30 Comments

#Anilam by Scott Redfern on 2007-05-31 14:34

One of the PCB boards in the controller came off it\'s mountings during transport and was damaged. The servos do not power up and the release for Spindle operation is not enabled (even in Spindle manual). Do you need the electrical schematics that I have to make the repair?

#Anilam by David on 2007-08-04 00:09

we got a new cnc lathe in our shope with an anilam crusader II control but if we try to jog the axis in manual mode you get an error code 18 we know what the book says about it but we do not know what to do to fix it any help would be greatly appreciatedThanks,David

#Anilam by christopher atwan on 2007-10-18 13:40

Did you reset the unit before you tried to jog it? Does it move at all before the error 18 code shows up?Christopher Atwan

#Anilam by muhammad amin on 2008-03-07 11:33

Dear SirHow we adjust the backlash in machinethanksAMIN

#Anilam by rasheed on 2008-05-20 11:30

sorry i have softlimit problem but do not know how to remove

#Anilam by OMAR AZHAR RANA on 2008-09-29 00:25

I have a Anilam Crusader II on my Milling Machine not working plz help me to know weather I can Retrofit an other unit with minimun change in parts and also tell me where I can get a complete Repair Manually of this THANKS OMAR AZHAR RANA

#Anilam by marc snel on 2008-10-19 17:49

i have a milling machine with a anilam crusader when i start up the machine he gives a error 18 after 3 seconds and the x as moves 0.5 mm the machine have indramat servos please can you help me

#Anilam by JOSE PRADA on 2008-11-26 19:16

We have an Anilam machine that is died.The screen show +x or -x limit. Can you help me?...Thanks..

#Anilam by Russell Bilby on 2009-02-24 17:52

hello, i have a cruasder m controller that has a broken membrane face where you push the program buttons. can you supply a new or good used one?and for what price, thanks Russell

#Anilam by Michael James on 2009-03-07 17:02

Russell,I may know where theres a used control \"head\" with a functional touch pad membrane. I sold one to a friend several years ago and I believe he never used it. Email me at drembedded_AT_yahoo_DOT_com with your contact info.Cheers,Michael

#Anilam by Minhas on 2009-10-23 16:43

Mr.Umer Azhar Rana We are in pakistan and we have all of Anilam Cursader II Help tell me in detail what condition of your,s Control You can replay below minhas1986@gmail.com

#Anilam by John Klingaman on 2010-03-10 00:42

I have an Anilam 1100 control that wont keep the cmos settings. The control starts to boot up but then tells me to push F2 to enter setup. I enter setup then save the changes but when I reboot the control does the same thing. What can be done to fix my problem?

#Anilam by steve wood on 2010-04-02 22:59

Hi john I called you earlier about connectors for servo driver card. We had cmos setting problems and fixed them on the 1100 by replacing the cpu board bios chip which contains internal batteries. We can walk you throughit if you need help. Interesting how your post about this problem poppedup in fr...
Show More

#Anilam by RANJIT SINGH on 2010-09-11 14:03

Sir, We have purchased 1 used Ernault Samoua milling Machine model ZHV-1.travels of the machine x,y,z are 710*270*400. Machine has been retrofittedwith Anilam Microprocessor model CRUSADER-2.problem with the machine isthat when machine is switched on, the display on the monitor is showingERROR-18 an...
Show More

#Anilam by RANJIT SINGH on 2010-09-20 16:16

WE NEED ELECTRICAL CIRCUIT DIAGRAM+REPAIRING MANUAL FOR ANILAM CRUSADER-2(3-AXIS).WHAT WILL BE THE CHARGES FOR THE SAME.

#Anilam by Richard S. Heckman Sr. on 2010-09-27 14:14

The Z axis is inoperative, manual movement of the Z axis results in the power contactor tripping out. This is the same contactor that is controlled by the limit switches. When the machine is first powered up the Y,X servo motors are powered, the Z is not getting power.

#Anilam by Muhammad Javed on 2010-10-10 15:58

Daer Sir,We are working on Anilam Since 4 years. We made many mould on it and machine working quality is good. So that is why we purchase one more Anilam 1100 machine from a old machinery ware house. but machine have no software, can you plz send us Anilam 1100`s software ver1.66. we will be very th...
Show More

#Anilam by K PRABHAKARA RAO on 2011-01-17 08:22

DEAR SIRORDNANCE FACTORY, MINISTRY OF DEFENCE, TIRUCHIRAPALLI- 620 016, (TAMILNADU STATE), SEARCHING FOR CNC SYSTEM AND DRIVE SERVICING AGENCY, WHO CAN REPAIR KIRLOSKAR CRUSADER MARK-II SYSTEM FITTED ON BFW VERTICAL MILLING MACHINE . KINDLY INTIMATE THE FEASIBILITY OF REAPAIRS OF THE SAME AT YOUR WO...
Show More

#Anilam by Gerald Hamilton on 2011-09-24 23:19

When I booted machine COMS battery state lowStandard COMS setupAdvance COMS setupauto configuration with BIOS defaultsauto configuration with power on defaultschange passwordauto detect hard diskauto detect hard disk utilitywrite to COMS and exitdonot write to COMS and exitI dont know where batterie...
Show More

#Anilam by chuck green on 2011-10-07 22:29

1100m on a bridgeport style knee mill,i was told the mother board is out. anyway to check it and how much would a replacement board cost.

#Anilam by Gary Boomgarden on 2011-11-16 20:43

We have a bridgeport with the 1100 anilam control on it. About a year ago the feed on the x @ y stopped working. Not able to engage the servos. We had a repairman come in who told us that the board that controls the servos is out. Have been waiting for him to have this repaired but has not found any...
Show More

#Anilam by Jose Maldonado on 2012-02-02 03:44

Hi I has a problem with a Lagun CNC with control anilam cruzader II I would like to buy the manual first and then expaint to you whats is our problem

#Anilam by abdoaakl on 2012-02-22 00:22

i need the Anilam Anilam Crusader II wiring Diagramabdoaakl-cairo - egypt-abdoaakl1@yahoo.comthanks for you.

#Anilam by chris hendricks on 2012-08-15 17:08

i need servo Y servo wiring diagram

#Anilam by kraig kather on 2012-09-12 12:44

I have no docs on servo power wiriing. Enable servo power on back of the crusader to does nothing. Do I have to reverse eng. this thing???

#Anilam by Ranjit Singh on 2012-09-16 17:23

Hi,I have a Arnault Samua machine ZXV1 which is fitted with Anilam Crusador 2 controller and Indramat TRM2 DC servo drives. When the machine is switched on , the controller displays ERROR CODE 12. and I am not able to enter anything. It is not accepting any command. I tried pressin Deelte Event butt...
Show More

#Anilam by piyush on 2012-10-14 04:42

i have anilam 1100 control with bridge port i have change Battery but now i have start machine y axis go to Negative direction and message Y axis lag over.

#Anilam by John Steimer on 2013-11-18 21:16

We have not used the machine with the Anilam SR1100 for several years.Replaced the battery and tried to reload the software but get the following message: Bad or Missing Shell ( command.com).I assume the discs have degraded.If you agree how do I get a new set of discs?Disk: 1100 M 2AXVer: 6.22A:use ...
Show More

#Anilam by carlos on 2018-03-16 16:56

I am sorry to hear that you are experiencing issues with your Anilam 501 901-159 circuit board. Can you please provide more details about the problem you are facing with the unit? Specifically, have you noticed any specific functionality that is not working as expected, such as error codes or malfun...
Show More

#Anilam by trammel rushing on 2018-09-24 15:54

where does the R5232 connect to

Contact Us

🚑Shop Location🛠️

Industrial Electronic Repair
145 Rockwell Place Ct
Tobaccoville, NC 27050
🚑 Rush repair shipments only — no walk-ins.

📞Phone

📦Mailing Address🚛

Industrial Electronic Repair
931-E S. Main St #204
Kernersville, NC 27284
📦 Mailing Address (for invoices or shipped repairs)
No walk-ins accepted.