Atlas Copco Service & Repair Forum
Electronikon shows converter failure 001.Siemans drive shows F0001. I was told that is motor failure.Test motor w/ 500 volt megemeter. showed no leakage to ground.Tested w/ ajustable AC Volt induction meter, trips @ 1700 volts / 10 meg ohms also trips trips @ 500 volt / 3 meg ohmsPulled fan cover, motor turns free. Observed motor rocking back and forth between fealds prior to trip F0001. Is the second test enough leakage to cause fault?
—> Purchase or Repair:
Reply🗨️Ask a New Question Below❓
Recent Comments Search: "Atlas Copco"
- Atlas Copco → Atlas Copco ELEKTRONIKON MARK IV 1900 0710 31 ↗
- Atlas Copco → Electronikon ↗
- Atlas Copco → Elektronikon Systems ES300 ↗
- Atlas Copco → Atlas Copco Compressor controller repair ↗
- Atlas Copco → Technical manual of Elektronikon ↗
- Atlas Copco → elektonikon ↗
- Atlas Copco → request for documentation ↗
- Atlas Copco → Atlas Copco 1900 0701 02 ↗
- Atlas Copco → error of system ↗
- Atlas Copco → ELECTRONIKON FAILURE ↗
- Atlas Copco → Error control compressor Atlas Copco ↗
- Atlas Copco → Atlas Copco Documentation GA90 ↗
- Atlas Copco → Training period ↗
- Atlas Copco → REGARDING QUOTE FOR ELEKTRONIKON 2 ↗
- Atlas Copco → Elektronikon n. 1900 0701 24 & 1900 0701 63 ↗
- Atlas Copco → Request manual ↗
- Atlas Copco → Technical manual of Elektronikon II ↗
- Atlas Copco → Documentation PDF Atlas Copco ↗
- Atlas Copco → ok ↗
- Atlas Copco → i want know elektronikon ll data sheet ↗
- Atlas Copco → Atlas Copco re request for documentation ↗
- Atlas Copco → Atlas Copco : Pls quote ↗
- Atlas Copco → Ankor Engineering ↗
- Atlas Copco → ELECTRONIKON Technical MAnual ↗
- Atlas Copco → Electronikon Manual ↗
- Atlas Copco → fault finding tips ↗
- Atlas Copco → request manual for elektronikon regulator ↗
- Atlas Copco → Need Touch keypad ↗
- Atlas Copco → 1900-0701-06 ELEKTRONIKON ↗
- Atlas Copco → MANUAL FOR GA4FF WITH ELETRONIKON II CONTROL ↗
- Atlas Copco → Atlas Copco : ELEKTRONIKON MASTERCONTROL MODULE REPAIR ↗
- Atlas Copco → re Elektronikon n. 1900 0701 24 & 1900 0701 63 ↗
- Atlas Copco → Elektronikon ↗
- Atlas Copco → quiery for Electronikon PLC communicaton ↗
- Atlas Copco → Electronikon manual ↗
- Atlas Copco → neded detail manual on all ELECTONIKON MASTER CONT ↗
- Atlas Copco → reques FOR INFORMATION ↗
- Atlas Copco → GA22 manual ↗
- Atlas Copco → elettronikon ↗
If you need your Atlas Copco unit tested or repaired,
give us a call at 1-336-969-0110.
We offer free estimates and extended warranties on the work performed.
Shipping/Receiving:
Industrial Electronic Repair
145 Rockwell Place Ct
Tobaccoville, NC 27050
Phone: 1-336-969-0110
Recent 1316 Comments
may I have the configuration software so Ican change the calibration of an pressure input
—> Purchase or Repair:
—> Purchase or Repair:
pls send to me manual dan part list compressor atlas copco ga55 ( soft copy )thanksutomo
—> Purchase or Repair:
—> Purchase or Repair:
The above module was recently replaced due to display and inputs \"freezing up\" and not functioning. The new module works fine. Can the malfunctioning module be rebuilt and tested? Perhaps the K4 relay, which sees a lot of action could also be replaced? How much cost? It was running on a 2004 ZT55 …Purchase or Repair: 
...
Show More
Show More
Could you please confirm if the Atlas Copco Elecktronikon 1900-0590-12 controller is still supported, and if replacement parts are available for it? Thank you.
—> Purchase or Repair:
—> Purchase or Repair:
we operating oil free compressor ZR160 and the electronikon MK3 displays an error which reads as follows: internal failure 7001please send me trouble shooting and solution to this problem.thank you francis bonful
—> Purchase or Repair:
—> Purchase or Repair:
The unit equipped with the Atlas Copco Elecktronikon 1900-0590-12 controller experienced downtime earlier today around 330 PM. We are investigating the issue and require a quick response to prevent further disruption. Thank you.
—> Purchase or Repair:
—> Purchase or Repair:
Dear Sr.I Need ELECTRONIKON technical Manual..P/N: 1900 0700 08 ed: 01serial: 02024700083Mário
—> Purchase or Repair:
—> Purchase or Repair:
please send for me electronikonmaster control module operating and trouble shoothing manual details
—> Purchase or Repair:
—> Purchase or Repair:
Dear Service Please to Help me , we have two Electronik II new , when I connect to GA 30 On the LCD Display shown :1220000011000000982039780931How can solve this problem?Thank you
—> Purchase or Repair:
—> Purchase or Repair:
Hi my name is Luis and i need a manual of elektronicon mk4 and mk3 for specifications of the compresor and display thankz for ur help
—> Purchase or Repair:
—> Purchase or Repair:
we are using 12 numbers of screw compressor from yours. it good in service we need the above document
—> Purchase or Repair:
—> Purchase or Repair:
Looking for repair service for Atlas Copco Electronikon 1900-0701-04 Display Unit. Screen not displaying any information, need quick resolution for production unit.
—> Purchase or Repair:
—> Purchase or Repair:
Dear sir or Dear MadamAfter ten days from our 8000 hours maintenance, we have now a starter feedback contact fault in our GA 160FF Model Atloas Copco Compresor.What would you like to recommend for this problem as solution?Thanks....
—> Purchase or Repair:
—> Purchase or Repair:
I want to request user manual elektronikon II panel control of air compressor model GA30 VSD FF.thanks & Pls, feedback to me as soon as.Thanks and best regards.
—> Purchase or Repair:
—> Purchase or Repair:
Hi Pls I need your help to resolve an alarm problem on GA7 Atlas Copco compressor .I have a message on display (oil separeter) and alarm red led blincking how can I solve this fault. Pls send me an information on Email :- nadid_elpal@yahoo.comBest Regards Nadid BurbarElectro Teck co.—> …Purchase or Repair: 
...
Show More
Show More
i like the way you care about your customers.eg u send yo technicalstaff to help us if we get ga 22 ff problems.
—> Purchase or Repair:
—> Purchase or Repair:
dear sir, we have 4 instrument air compressor operating in MCC, No 1 compressor is master control for 3 compressors.we have one problem in atlas copco instrument air compressor no 3 this is not communicating with instrurment air compressor 1 and not sending to DCS also it means all process parameter…Purchase or Repair: 
...
Show More
Show More
Dear sir , Kindly arrange us to send the quote for elektronikon -2Thanks & regards S. Balaji
—> Purchase or Repair:
—> Purchase or Repair:
Can you please verify if the Atlas Copco 1900-0700-08 Controller is still supported or if replacement parts are available for this older unit? Thank you.
—> Purchase or Repair:
—> Purchase or Repair:
Hello,We are having issues with a GA30+ compressor. The controller is not accessible. It has a fault code that is locking out the controller and causing the not to start . The display on the controller is indicating B -SW 0106. Please can you assist by sending me a Troubleshooting/Service Manual and…Purchase or Repair: 
...
Show More
Show More
Do you have a replacement controller available for the Atlas Copco GA45 1900.0590.74? Our unit has gone down and we need to keep production running.
—> Purchase or Repair:
—> Purchase or Repair:
Dear sir,please send the Spare parts manual for GA22 air compressor for ordering spare from the local dealer.Thanks and regards,Chiranjeevi RajuManager- Maintenance.
—> Purchase or Repair:
—> Purchase or Repair:
I have an atlas copco compressor GA75 when switch on power it appears on the display 100300000000 and cannot start the compressor and also no touch switch are working .Please advice urgently
—> Purchase or Repair:
—> Purchase or Repair:
My GA 50VSD has a Simens Simovert inverter. 6SE7031-5EF20-OBBO. I have an E message on the screen. According to the manual I need to replace CU board. Can you help?
—> Purchase or Repair:
—> Purchase or Repair:
Hello, I am reaching out on behalf of a client regarding an issue with an Atlas Copco Elektronikon II 1900 0710 12 controller. Can you please provide information on potential repairs or troubleshooting steps for this specific part? Thank you.
—> Purchase or Repair:
—> Purchase or Repair:
Dear Sir,Can you give me the manual for elektronikon ?I need to looking for the password for set the range sensor. Because my compressor cannot start because it.please help meBest RegardsHamdi Ayussa
—> Purchase or Repair:
—> Purchase or Repair:
I have an Atlas Copco dryer FD410 in which I have problems with high pressure alarm in the refrigerant line and even I just presented a "dewpoint" alarm. You can, I suppose, support sending the manual with the faultsFirst of all, Thanks.
—> Purchase or Repair:
—> Purchase or Repair:
please tell me what can I do about alarm 110200000000 in display on air compressor atlas-Copco, GA 90 thank you very much serial number 0006004900031part number 900070124
—> Purchase or Repair:
—> Purchase or Repair:
please send me user manual and schematic diagram of elektronikon p/n:1900 0701 23s.n:0698 2800 149ed:0024vac
—> Purchase or Repair:
—> Purchase or Repair:
the Elektronikon 1900070008 panel on the Atlas Copco screw compressor unit went down mid-shift. Needs someone to look into it ASAP. Thanks!
—> Purchase or Repair:
—> Purchase or Repair:
need a user manual or someone to contact me on 0407000457 to get our compressor going again, won\'t start after a blackout
—> Purchase or Repair:
—> Purchase or Repair:
We have one Atlas copco compressor model: GA75VSD The compressor contains a MM440 Siemens drive. (6SE6440-2UD38-8FA1)The drive has been damaged and we need the application Parameters for the drive.Best regardsKlaus
—> Purchase or Repair:
—> Purchase or Repair:
I work in Jindal Stainless Limited in India..and we has the air compresor ATLAS COPCO( model no-ZR275)...and we has problem with controler ELEKTRONIKON...We are not receiving any display on the regulator inspite of giving a regular 24V supply and its interfacing with SI/O module.Please also send the…Purchase or Repair: 
...
Show More
Show More
—> Purchase or Repair: