Atlas Copco Service & Repair Forum

Originally had to send the simovert drive for repair due toit faulting on f11 and f26. The repair company told there had replaced 2 faulty items carried out a function test. all ok. They then returned the drive which I subsequently refitted and powered the compressor up and tried to start it only get 7301 displayed on the elektronican. Presumed that this was due to a communication problem between simovert drive and display. I telephoned the repair company and they told me they had tested the drive by hard wiring it and not used any serial communication device. I have tried everything to try to get elektronican to communicate but as yet have had no success. I have now made a mistake by resetting the parameters and only have a list of parameters up to 500. Any help wouldbe greatly appreciated. Thanks J Mitchell

—> Purchase or Repair: Ticket Image

— Posted by J Mitchell on 2013-05-09

Reply🗨️Ask a New Question Below❓


Recent Comments Search: "Atlas Copco"

If you need your Atlas Copco unit tested or repaired,
give us a call at 1-336-969-0110.
We offer free estimates and extended warranties on the work performed.
Shipping/Receiving:
Industrial Electronic Repair
145 Rockwell Place Ct
Tobaccoville, NC 27050
Phone: 1-336-969-0110

Recent 1316 Comments

#Atlas Copco by Humaid salim al-Mahrouqi on 2010-12-07 11:37
Dear Sir,I would like to know if your able to repaire MLVA unit for Noritsu machine model no 2901. If yes what is your coast of repair?regards,Humaid

—> Purchase or Repair:
➡️ Reply
#Atlas Copco by francisco juarez on 2009-10-30 01:33
i need the manual for elektronikon IIthank you

—> Purchase or Repair:
➡️ Reply
#Atlas Copco by satish on 2009-07-27 16:03
we are using 12 numbers of screw compressor from yours. it good in service we need the above document

—> Purchase or Repair:
➡️ Reply
#Atlas Copco by Alcantara on 2012-02-18 12:17
I'm experiencing some issues with the Atlas Copco 1900-0700-08 controller, as something seems to have stopped working properly. I'm not entirely sure what the model does, but I would appreciate some assistance in resolving this issue. Thank you.

—> Purchase or Repair:
➡️ Reply
#Atlas Copco by hadi on 2009-11-02 02:53
hello,dear! my company have two compressor model ga55 ff. and this compressors is good product. But I have problem abaut \" dp oil separator\". It problem is pressure to high. To high from maximum servise [ 1 bar ].Please, can you help for this problem?

—> Purchase or Repair:
➡️ Reply
#Atlas Copco by aamir on 2013-07-05 15:09
we are using GA75 Atlas Copco the ELEKTRONIKON MODULE showing fault \'system failure\' so please give us some solution to rectify above problem thanks and regards

—> Purchase or Repair:
➡️ Reply
#Atlas Copco by kevin schofield on 2014-12-10 21:24
Please send the operation manual for the ElektroniconII on our 2006 compressor. type GA11VSDNr AP1160620I am in need of the manual for the Elektronikon II only.Thank you,kevi schofield

—> Purchase or Repair:
➡️ Reply
#Atlas Copco by Dante Linares on 2008-09-21 20:36
Dear Sr.I Need ELECTRONIKON II technical Manual..Dante LinaresC. M. AntaminaTelef 1 51 2173647AncashPeru

—> Purchase or Repair:
➡️ Reply
#Atlas Copco by manik chandra kar on 2010-09-22 18:45
dear sir i want to your produt manual modle no GA55 for my job perpose

—> Purchase or Repair:
➡️ Reply
#Atlas Copco by Bala on 2016-12-24 16:31
Hi,How to reset Elektronikon password to enable "modify parameters" load and unload setting.

—> Purchase or Repair:
➡️ Reply
#Atlas Copco by Miroslav Virok on 2011-04-18 09:27
Comunikation manual Elektrikom 2.Thamks

—> Purchase or Repair:
➡️ Reply
#Atlas Copco by Marcos Bartoloni on 2008-09-29 18:52
Good afternoon people. I need a PDF copy of the elektronicon 1900 0700 03 control module, because we have an error that its shown on the display, and we want to start and investigation of it, but we need the information about the control module. Reggards Marcos Bartoloni EDELCA, VENEZUELA—> …Purchase or Repair: Ticket Image...
Show More
➡️ Reply
#Atlas Copco by Muhammad Mansoor on 2009-07-16 08:46
We have replaced the module of G11A with the module of G11FF , kindly do advise as it is giving sensor light ,

—> Purchase or Repair:
➡️ Reply
#Atlas Copco by Watson Sawadye on 2008-11-20 05:15
I would like to tap a signal from the Electronika module and connect it to the PLC as well as SCADA.I need to know where to do it and how that can be acieved.So would it be possible to get a copy of the Electronika II Technical manual?

—> Purchase or Repair:
➡️ Reply
#Atlas Copco by tor on 2009-04-04 03:42
We need the Atlas copco Pass Word to Reboot the ECU Electronic System on the GA37( forgot pass word)

—> Purchase or Repair:
➡️ Reply
#Atlas Copco by Yalember Setotaw on 2017-01-24 07:07
Best Brand i ever see

—> Purchase or Repair:
➡️ Reply
#Atlas Copco by ahmed aly on 2009-06-29 14:16
Dear Sir,I would like to request the technical detailed catalogue for your compressor type GA5 FF S/N: AII 158303 as we need the technical catalogue for it (including troubleshooting procedures) thank youAhmed A. Aly | Chief EngineerIHG Port Ghalib | PO Box 23, Port Ghalib, Marsa Alam, Red Sea, Egyp…Purchase or Repair: Ticket Image...
Show More
➡️ Reply
#Atlas Copco by ASHRAF KHLIL on 2010-12-06 00:07
Electronikon II controller

—> Purchase or Repair:
➡️ Reply
#Atlas Copco by SALMAN on 2018-11-23 05:40
GA 37 part list manual is of importance to enable my company get genuine parts

—> Purchase or Repair:
➡️ Reply
#Atlas Copco by nassim zouaoui on 2013-12-30 14:27
operating manual thank youragrds

—> Purchase or Repair:
➡️ Reply
#Atlas Copco by msureshchander on 2010-10-14 06:13
good efficiency compressor

—> Purchase or Repair:
➡️ Reply
#Atlas Copco by Ghislain Gagnon on 2010-03-06 18:01
J\'ai besoin de connaitre les contacts auxiliaires du compresseur pour qu\'il démare un ventillateur quand il démare.

—> Purchase or Repair:
➡️ Reply
#Atlas Copco by PHAM HAI on 2011-09-01 04:30
Dear Sir, I am from VN, I have one machine Ga22 ( year 2001)now, controller alarm: system failure 11 & 104. machine can not run.I turn off the power and turn on but machine can not run!Pls, tell me, what must I do?Thanks & best regards,

—> Purchase or Repair:
➡️ Reply
#Atlas Copco by yahya asy on 2009-02-02 14:05
please i need service manual for Elektronikon II

—> Purchase or Repair:
➡️ Reply
#Atlas Copco by GANESH on 2009-06-06 12:45
dear sir, i have elektronikon II unit but some problem is inside i want some information ragarding cirquit digram or IC Details used in unit i hope u will give me response kindly.. Thanks ganesh

—> Purchase or Repair:
➡️ Reply
#Atlas Copco by bill berke on 2012-04-07 01:55
The Atlas Copco 1900-0700-08 controller just failed - drive or board issue. Need immediate attention to resolve the problem.

—> Purchase or Repair:
➡️ Reply
#Atlas Copco by alinavaz merchant on 2012-01-05 12:19
dear sir,my atlas copco scrow air comprassor display folt folt 200 so what can i do pleas give your manualthanksalinavaz merchant

—> Purchase or Repair:
➡️ Reply
#Atlas Copco by ARUN KUMAR SRIVASTAVA on 2011-05-28 13:17
Pl send me immediately the detail part nos. of Manual of GA 55 AWP.

—> Purchase or Repair:
➡️ Reply
#Atlas Copco by Gary Jelen on 2009-12-19 16:47
Pleas can you send me an operation manual for the Elektronikon

—> Purchase or Repair:
➡️ Reply
#Atlas Copco by Norm Hodder on 2011-12-25 11:07
We have this compressor on board our rig and we require a download schematic. Can you tell me how I can get thisNorm

—> Purchase or Repair:
➡️ Reply
#Atlas Copco by mohamed ait lahssaine on 2021-06-28 11:00
i have a problem with compressor i need the drowing to solve this problemthanks

—> Purchase or Repair:
➡️ Reply
#Atlas Copco by mohamed on 2011-01-20 18:56
I need spare parts , INSTRUCTION , AND MAINTENANCE list for air copressor ga 55plus , ga 55

—> Purchase or Repair:
➡️ Reply
#Atlas Copco by Darek on 2012-06-19 18:13
I need manual for GA15ff

—> Purchase or Repair:
➡️ Reply
#Atlas Copco by Wimol F on 2013-07-24 18:32
The Atlas Copco GA45 1900.0590.74 is down due to a controller issue. Please have someone check it first thing in the morning.

—> Purchase or Repair:
➡️ Reply
#Atlas Copco by khushnood on 2009-06-16 06:54
need software to connect the Elektronikon control module with pc and and need all hex file of Elektronikon control module

—> Purchase or Repair:
➡️ Reply
#Atlas Copco by Chiranjeevi Raju on 2012-04-16 11:55
Dear sir,please send the Spare parts manual for GA22 air compressor for ordering spare from the local dealer.Thanks and regards,Chiranjeevi RajuManager- Maintenance.

—> Purchase or Repair:
➡️ Reply
#Atlas Copco by Wawan Arif on 2012-05-07 04:16
help me please,I can not activate the remote start stop?i use elektronikon operation system 1900523027Board Modul 1900524001

—> Purchase or Repair:
➡️ Reply
#Atlas Copco by ibrahim abdel salam on 2008-09-10 00:36
manual and offer to get repaired or new panel

—> Purchase or Repair:
➡️ Reply
#Atlas Copco by georgi on 2009-11-01 12:30
how much is the price of regulator part nr: 1900 0701 06

—> Purchase or Repair:
➡️ Reply
#Atlas Copco by surendra kumar shahani on 2010-11-18 11:50
Pls send to me, manual repair for compresso Atlas Copco ga55thanks

—> Purchase or Repair:
➡️ Reply
#Atlas Copco by Ignacio Choque on 2010-12-05 15:17
I ned help for install module elektronikon.

—> Purchase or Repair:
➡️ Reply
#Atlas Copco by Nguyen Ngoc Quang on 2009-11-06 16:27
My company use air compressor system of atlas copcobut i don\'t have manual about electronikon II, because I can\'t modify any parameter. I want to have manual about atlas copco GA75+ (both mechanical and electrical manual). My company is Cement Hatien 1 stock company. Can you help me?Thanks & best …Purchase or Repair: Ticket Image...
Show More
➡️ Reply
#Atlas Copco by ajit on 2011-03-30 05:50
Dear Sir/Madam ;we have GA7 and GA7FF Compressors. We need this units\' documents as soon as possible. Please send me GA7 and GA7FF Compressors\' Installation Operation and Maintenance Manuals.Waiting for your reply as soon as possibleBest Regards,Ajit kumar

—> Purchase or Repair:
➡️ Reply
#Atlas Copco by V S yadav on 2012-03-31 13:18
Dear sirMy elektronikon\'s power of every 15 minut Please sugestV s yadav9351471656

—> Purchase or Repair:
➡️ Reply
#Atlas Copco by aziz on 2015-03-26 09:20
dear sir, please send me the inverter parameters. best regards

—> Purchase or Repair:
➡️ Reply
#Atlas Copco by Mauro leonardo Zarate on 2012-04-04 21:59
He tenido algunos detalles de mi compresor que resuelvo con su manual, estare muy agradecido si me hace el favor de proporcionarmelo.Saludos

—> Purchase or Repair:
➡️ Reply
#Atlas Copco by george on 2011-05-10 07:16
the module on condition only display back light glow.no message displayed

—> Purchase or Repair:
➡️ Reply
#Atlas Copco by andrew matewu on 2019-06-19 10:11
Hello,I have a Atlas Copco ga55 compressor, the display show 100400000000when power up and nothing else is funtion. what wrong with the controller or machine? Thanks,

—> Purchase or Repair:
➡️ Reply
#Atlas Copco by Martin Ramiro Juarez on 2010-04-21 17:37
I'm experiencing some issues with the Atlas Copco Elektronikon 1900070124 controller. It seems like something has stopped working, but I'm not exactly sure what it does. Any help or guidance would be greatly appreciated.

—> Purchase or Repair:
➡️ Reply
#Atlas Copco by labinot on 2014-12-29 11:54
Hello MR. I have the same problem, do you find the solution?

—> Purchase or Repair:
➡️ Reply

Contact Us

🚑Shop Location🛠️

Industrial Electronic Repair
145 Rockwell Place Ct
Tobaccoville, NC 27050
🚑 Rush repair shipments only — no walk-ins.

📞Phone

1-336-969-0110

📦Mailing Address🚛

Industrial Electronic Repair
931-E S. Main St #204
Kernersville, NC 27284
📦 Mailing Address (for invoices or shipped repairs)
No walk-ins accepted.