Cybelec for Service call 1-336-969-0110 at Industrial Electronics Repair

Cybelec Service & Repair Forum

previo cordial saludo me comunico con uds. por q soy propietario de una plegadoramarca hammerle con control dnc y quisiera saber como puedo obtener el manual de usuario para poder hacer uso de el.agradecido de antemanome despido de ud.atte lucio gamarra sotocusco peru

— Posted by lucio gamarra on 2010-12-30

Reply🗨️Ask a New Question Below❓

If you need your Cybelec unit tested or repaired,
give us a call at 1-336-969-0110.
We offer fair estimates and extended warranties on the work performed.
Shipping/Receiving:
Industrial Electronic Repair
145 Rockwell Place Ct
Tobaccoville, NC 27050
Phone: 1-336-969-0110

Recent 16 Comments

#Cybelec by walid on 2008-09-14 07:29

We are facing a problem in our bending machine which is controlled by cybelec modeva-10 where upon switching on the machine only white screen appear on monitor and as some technicians informed us that maybe they cpu is defected so kindly inform us if it can be repair and the cost of such problem and...
Show More

#Cybelec by Walter Krahenbuhl on 2009-02-03 15:50

Good Morning,We have a Cybelec DNC 7400 Controller (serial #444) on one of our Press Brakes that is not operating correctly. We have narrowed the problem down to the NX2-103 board ( Cybelec SA N2X102), but can not find a replacement. Do you have a board available to sell us? If not, can you repair t...
Show More

#Cybelec by Peter Dieperink on 2009-04-26 11:14

Are you still looking for a repair of this control or has your problem been solved in the meantime?We can repair most of the Cybelec controls and we can aslo supply spare parts for it.Please don\'t hesitate to contact me.

#Cybelec by Peter Dieperink on 2009-04-26 11:16

Dear Sir,We have new N2X boards for DNC7000 series available.Are you still looking for one?Please don\'t hesitate to contact me.Peter Dieperink

#Cybelec by ALIREZA on 2009-12-22 07:28

HelloPlease monitor the messages that come on help me.Message is:AUSFUEHRUNGSKOD ---

#Cybelec by Ernesto Reyes on 2010-02-20 03:56

We have a trouble with a DNC 60, when we turn on the machine, it ask us a password, but the last operator had put a new password and we don\'t know it. How can we reset that password and leave it clean? We have so many requests pending and we need to operate it as soon possible. Can we clean it with...
Show More

#Cybelec by lucio gamarra on 2010-12-30 23:22

previo cordial saludo me comunico con uds. por q soy propietario de una plegadoramarca hammerle con control dnc y quisiera saber como puedo obtener el manual de usuario para poder hacer uso de el.agradecido de antemanome despido de ud.atte lucio gamarra sotocusco peru

#Cybelec by lucio gamarra on 2011-01-07 05:15

hello i am from peru i have a dnc 7000 i need the manual because i can´t work it please send if you have it

#Cybelec by Gonzalo Gonzalez on 2011-01-26 20:25

Good after noon sirwe run a Hurco PR150-3100 with a Cybelec DNC60 controller had a tech try to replace the battery he disconected the ground cables in the back of the controller and our screen whent from the main page to this message even afetr we re-installed the ground cables back thescreen doesn\...
Show More

#Cybelec by Francois on 2011-01-30 10:18

we need your assistance in CYBELEC DNC 60 G CONT0RLLER.is not accepting data.

#Cybelec by Yuri on 2011-05-23 15:49

How I can reset CMOS password on mainboard S-CPU-4472/G-06m07D

#Cybelec by Vyacheslav on 2012-09-24 08:08

NC - Cybelec SA Type DNC-7400-PSGY Serial ¹ 2737CNC press brake is set to GWF System MENGELEType H160-3/4 1989g.v Fabr Nr.10556fault - N2X-102 - NSP-102

#Cybelec by Paulo Cyrus G. Abaring on 2013-04-28 00:00

Experiencing issues with my Cybelec 112 industrial unit's circuit board. Need a repair specialist to diagnose and fix the malfunction.

#Cybelec by Jacques Erades on 2014-01-23 00:00

Cybelec DNC 53 P not responding to inputs, display screen is blank. Looking for repair service for control module unit. Please advise on availability.

#Cybelec by Larry Unruh L on 2017-02-05 00:00

Cybelec ModEva 10 CPU control unit not powering on or responding. Need repair service urgently.

#Cybelec by Bulama on 2023-05-04 21:43

: My Cybelec ModEva 10 monitor has stopped displaying an image. It appears to be a functional problem with the display itself, as I can hear the fan, and there is no error message on screen. The monitor was recently placed in use, so it's still under warranty. I am concerned about the cost of repair...
Show More

Contact Us

🚑Shop Location🛠️

Industrial Electronic Repair
145 Rockwell Place Ct
Tobaccoville, NC 27050
🚑 Rush repair shipments only — no walk-ins.

📞Phone

📦Mailing Address🚛

Industrial Electronic Repair
931-E S. Main St #204
Kernersville, NC 27284
📦 Mailing Address (for invoices or shipped repairs)
No walk-ins accepted.