Cybelec Service & Repair Forum

Are you still looking for a repair of this control or has your problem been solved in the meantime?We can repair most of the Cybelec controls and we can aslo supply spare parts for it.Please don\'t hesitate to contact me.

—> Purchase or Repair:

Reply🗨️Ask a New Question Below❓

• Cybelec → Cybelec ↗
• Cybelec → Cybelec V-AST-241A33 ↗
• Cybelec → Cybelec MODEVA 10 ↗
• Cybelec → dnc 7000 ↗
• Cybelec → Cybelec DNC60 locked ↗
• Cybelec → Cybelec S-MB8-204 ↗
• Cybelec → Cybelec N2X Board for DNC7400 ↗
• Cybelec → Repair ↗
• Cybelec → Cybelec DNC 53 P ↗
• Cybelec → DNC 60 locked ↗
• Cybelec SA → Cybelec Sa DNC 7000 ↗
• Cybelec → application ↗
• Cybelec → Cybelec NSU 120 ↗
• Cybelec → manual dnc7000 ↗
• Cybelec → Cybelec cybelec modeva-10 ↗
• Cybelec → Cybelec DNC 800 ↗
• Cybelec → Cybelec 112 ↗
• Cybelec → Cybelec : N2X board for DNC7000 series ↗
• Cybelec → Ryazan ↗
• Cybelec → Reapir ModEva control ↗

Recent 21 Comments

#Cybelec by Bulama on 2023-05-04 21:43

: My Cybelec ModEva 10 monitor has stopped displaying an image. It appears to be a functional problem with the display itself, as I can hear the fan, and there is no error message on screen. The monitor was recently placed in use, so it's still under warranty. I am concerned about the cost of repair…Purchase or Repair: ...: My Cybelec ModEva 10 monitor has stopped displaying an image. It appears to be a functional problem with the display itself, as I can hear the fan, and there is no error message on screen. The monitor was recently placed in use, so it's still under warranty. I am concerned about the cost of repair or replacement considering that the unit is a relatively new purchase. Could you please provide an estimate for a potential repair or replacement? I believe this issue may be related to a malfunctioning display panel and would like to know if replacing the entire monitor might be the most efficient solution. Any information on repair costs, estimated turnaround time, and warranty coverage would greatly assist me in making a decision.:

—> Purchase or Repair:
Show More

➡️ Reply

#Cybelec by Ernesto Reyes on 2010-02-20 03:56

We have a trouble with a DNC 60, when we turn on the machine, it ask us a password, but the last operator had put a new password and we don\'t know it. How can we reset that password and leave it clean? We have so many requests pending and we need to operate it as soon possible. Can we clean it with…Purchase or Repair: ...We have a trouble with a DNC 60, when we turn on the machine, it ask us a password, but the last operator had put a new password and we don\'t know it. How can we reset that password and leave it clean? We have so many requests pending and we need to operate it as soon possible. Can we clean it with a bridge between some terminals? Removing the power supply, could be the solution?We apreciate your attention.Best Regards

—> Purchase or Repair:
Show More

➡️ Reply

#Cybelec by walid on 2008-09-14 07:29

We are facing a problem in our bending machine which is controlled by cybelec modeva-10 where upon switching on the machine only white screen appear on monitor and as some technicians informed us that maybe they cpu is defected so kindly inform us if it can be repair and the cost of such problem and…Purchase or Repair: ...We are facing a problem in our bending machine which is controlled by cybelec modeva-10 where upon switching on the machine only white screen appear on monitor and as some technicians informed us that maybe they cpu is defected so kindly inform us if it can be repair and the cost of such problem and time required for such repair CPU board, Type S-CPU-4472/B-01g01D The screen model: v-modeva-10 Type: DNC-ME-10D-A Serial: 0343 The cpu unit model: v-cnc lcc04ps2d Type: CNC-ME04 PSlc Serial: 0172 Your fast reply will be highly appreciated Best regards Walid naim RIYADH FACTORY FOR PANEL BOARDSP.O BOX:60454 RIYADH 11545 SAUDI ARABIA TEL: 009661...FAX: 0096614985879

—> Purchase or Repair:
Show More

➡️ Reply

#Cybelec by Gonzalo Gonzalez on 2011-01-26 20:25

Good after noon sirwe run a Hurco PR150-3100 with a Cybelec DNC60 controller had a tech try to replace the battery he disconected the ground cables in the back of the controller and our screen whent from the main page to this message even afetr we re-installed the ground cables back thescreen doesn\…Purchase or Repair: ...Good after noon sirwe run a Hurco PR150-3100 with a Cybelec DNC60 controller had a tech try to replace the battery he disconected the ground cables in the back of the controller and our screen whent from the main page to this message even afetr we re-installed the ground cables back thescreen doesn\'t change and it won\'t let me into any other page any advice Thank you G.Ginitialisation DNC 60 ZONE PARAMETERS.. EFFACEMENT ZONE VARIABLES.. EFFACEMENT ZONE PARAMETERS MACHINE..EFFACEMENT ZONE TRANSFERI...CODE D\'EXECUTION.

—> Purchase or Repair:
Show More

➡️ Reply

#Cybelec by Calvert on 2025-06-06 10:42

Hello, I'm interested in purchasing a Cybelec NSU 120 CPU board. I'm not entirely certain if this is the correct model, but my team suggested reaching out to inquire. Could you please provide information on pricing and availability? We are looking to source one quickly. Thank you.—> …Purchase or Repair: ...Hello, I'm interested in purchasing a Cybelec NSU 120 CPU board. I'm not entirely certain if this is the correct model, but my team suggested reaching out to inquire. Could you please provide information on pricing and availability? We are looking to source one quickly. Thank you.

—> Purchase or Repair:
Show More

➡️ Reply

#Cybelec by Walter Krahenbuhl on 2009-02-03 15:50

Good Morning,We have a Cybelec DNC 7400 Controller (serial #444) on one of our Press Brakes that is not operating correctly. We have narrowed the problem down to the NX2-103 board ( Cybelec SA N2X102), but can not find a replacement. Do you have a board available to sell us? If not, can you repair t…Purchase or Repair: ...Good Morning,We have a Cybelec DNC 7400 Controller (serial #444) on one of our Press Brakes that is not operating correctly. We have narrowed the problem down to the NX2-103 board ( Cybelec SA N2X102), but can not find a replacement. Do you have a board available to sell us? If not, can you repair this? Please provide costs and turn-around time ASAP. Thank you.

—> Purchase or Repair:
Show More

➡️ Reply