Excellon Automation for Service call 1-336-969-0110 at Industrial Electronics Repair

Excellon Automation Service & Repair Forum

Display screen of the control panel shows the value of memory registers and do not boot the machines from any of the floppy drives. We also have tried to reset and boot it manually by BO,0 and BO,1 commands as given in the manuals. What might be the problem and how to solve it. Looking forward for a positive reply.Regards

— Posted by M. Salman Mughal on 2010-09-21

Reply🗨️Ask a New Question Below❓

If you need your Excellon Automation unit tested or repaired,
give us a call at 1-336-969-0110.
We offer fair estimates and extended warranties on the work performed.
Shipping/Receiving:
Industrial Electronic Repair
145 Rockwell Place Ct
Tobaccoville, NC 27050
Phone: 1-336-969-0110

Recent 15 Comments

#Excellon Automation by Qaiser Afzal on 2006-12-17 09:14

Dear Sir/Madam,Iv\'e lost my \"Excellone CNC-6 with EX-110\" Operating System and Softwarehow can i purchase or download this?

#Excellon Automation by paresh patel on 2007-01-26 01:51

dear sir,we are mfg pcb in india we have 4 machine excellonwe need two number vdc(vidio display card) & one repairingwe also need sofware original for ex-300 machinethanking you,your faithfully,gmcparesh patel

#Excellon Automation by paresh patel on 2007-01-26 01:53

dear sir,we are mfg pcb in india we have 4 machine excellonwe need two number vdc(vidio display card) & one repairingwe also need sofware original for ex-300 machinethanking you,your faithfully,gmcparesh patel

#Excellon Automation by sergio rojas on 2009-12-18 17:04

Dear Sir/Madam,Iv\'e lost my \"Excellone CNC-6 with EX-300 D/R\" Operating System and Softwarehow can i purchase or download this?HELP

#Excellon Automation by sergio rojas on 2009-12-18 17:06

we also need sofware original for ex-300 machineSERGIOAJI123@HOTMAIL.COM;SERGIOEMPRESA@HOTMAIL.COM

#Excellon Automation by ashraf bandeshah on 2009-12-23 07:54

WE NEED HARD DISK FOR OUR EXCELLON DRILLER/ROUTER CNC 6 EX200 MACHINE WITH BOOTABLE FEATURE.

#Excellon Automation by vijay on 2010-04-11 13:00

Dear Sir,I have one system 2000s excellon machine with cnc 07 console.I have a problem related software.I have installed four floppy in machine but after bootiung machine again it reboot system automatically.and if I remove the I/O-1 board power then it but full software but in mach file it shows co...
Show More

#Excellon Automation by Carlos Alarcón Vergara on 2010-07-20 14:59

Dear Sir/Madam,Iv\'e lost my \"Excellone CNC-6 with EX-300\" Operating System and Softwarehow can i purchase or download this? 1. WE NEED HARD DISK FOR OUR EXCELLON DRILLER/ROUTER CNC6 EX300 MACHINE WITH BOOTABLE FEATURE. 2. we also need sofware original for ex-300 machine3. SOFWARE EX-300...
Show More

#Excellon Automation by jeevan potluri on 2010-09-19 15:37

i need manual for excellon ex 300.

#Excellon Automation by M. Salman Mughal on 2010-09-21 04:53

Display screen of the control panel shows the value of memory registers and do not boot the machines from any of the floppy drives. We also have tried to reset and boot it manually by BO,0 and BO,1 commands as given in the manuals. What might be the problem and how to solve it. Looking forward for a...
Show More

#Excellon Automation by mrajamouli on 2010-10-13 10:59

sir my vdc card is proc

#Excellon Automation by Peter Frankish on 2010-12-19 08:56

Dear Sir, I have a problem with our XL5 D/R. TheD/R software will not run although i can run a MK V drilling software. Do you know what revision software the XL5 D/R should be running? and do you have any idea why the drilling software for MK V or EX200 will run but the D/R software will not. Many t...
Show More

#Excellon Automation by sivaramakrishna.d on 2011-04-21 02:35

Dear Sir, need excellon cnc6 cpu cord ,please send quote. Thanking you. sivaramakrishna.d M.S.ELECTRONICS. PHONE.+91-9293159245 +91-40 32585812

#Excellon Automation by Brandon on 2017-01-04 16:23

Contact Tim with PCB Machine ServicesHe works on Excellon Equipment and has helped me out a few times.Email: Tim@PCBMachineServices.com

#Excellon Automation by Ajay thaya on 2025-04-28 13:36

Once machine boots, home page shows error code as faulty limit switch , right travel limit

Contact Us

🚑Shop Location🛠️

Industrial Electronic Repair
145 Rockwell Place Ct
Tobaccoville, NC 27050
🚑 Rush repair shipments only — no walk-ins.

📞Phone

📦Mailing Address🚛

Industrial Electronic Repair
931-E S. Main St #204
Kernersville, NC 27284
📦 Mailing Address (for invoices or shipped repairs)
No walk-ins accepted.