Graseby/Goring-Kerr Service & Repair Forum

Hi, This is Mayank from India(Makson\'s Nutrition),We posses a metal detactor by you,request you to send a manual for its operation. As it is not working properly.Serial No:4833RegardsMayank00919302611867

— Posted by Mayank Agarwal on 2009-04-13

Reply🗨️Ask a New Question Below❓


Recent Comments Search: "Graseby/Goring-Kerr"

If you need your Graseby/Goring-Kerr unit tested or repaired,
give us a call at 1-336-969-0110.
We offer free estimates and extended warranties on the work performed.
Shipping/Receiving:
Industrial Electronic Repair
145 Rockwell Place Ct
Tobaccoville, NC 27050
Phone: 1-336-969-0110

Recent 85 Comments

#Graseby/Goring-Kerr by VICTOR CHANG on 2011-06-26 15:38
Dear sir : We had bought a GRASEBY CHECKWEIGHER with type E30 , S/N: B56645, Date : 31-07-98, and found problems as follows recently 1. When product be put in load cell , the reading moves up and down and is unstable. 2. When trim calibration , we run prodct many times to weighing and found some of …...
Show More
➡️ Reply
#Graseby/Goring-Kerr by Prakash Panchal on 2015-07-10 07:20
We required user manual for Graseby/goring Kerr Metal detector R-1940607.
➡️ Reply
#Graseby/Goring-Kerr by mario valente on 2009-03-31 14:37
I bought a used metal detector but have no manual, can you please find and send one to me. tks, regards,
➡️ Reply
#Graseby/Goring-Kerr by matthew lamontagne on 2009-12-21 05:27
If you can send me a parts breakdown of dsp-2 goring kerr it will be appreciated greatly. Thanks, Matthew Lamontagne
➡️ Reply
#Graseby/Goring-Kerr by Jesus on 2010-09-09 21:31
There is a fault in a metalcheck goring kerr tek 21, the fault is \"search head\" I can\'t not enable this problem
➡️ Reply
#Graseby/Goring-Kerr by sameera abeysinghe on 2010-12-07 18:45
can you get me oparating manual of TEK21 machine.thanks.
➡️ Reply
#Graseby/Goring-Kerr by Irfan on 2009-12-29 08:17
We would like to have some technical details of Best checkweigher D30.
➡️ Reply
#Graseby/Goring-Kerr by Mark on 2011-05-25 16:00
Does anybody know the special password required for the system config ?
➡️ Reply
#Graseby/Goring-Kerr by Terri Beach on 2009-03-12 14:17
I am trying to get a manufacture spec sheet on a goring kerr tek dsp
➡️ Reply
#Graseby/Goring-Kerr by Jim on 2011-04-19 20:33
Graseby G K no longer exists. The company that purchased them is Thermo Fisher Scientific. May be you could try that name in Poland. Good luck.
➡️ Reply
#Graseby/Goring-Kerr by Jim on 2011-04-19 20:41
Hi, did you locate a manual?
➡️ Reply
#Graseby/Goring-Kerr by Jesus Lamas on 2010-09-10 14:17
there is a fault \"search head\" I can not enable this fault.
➡️ Reply
#Graseby/Goring-Kerr by Melissa Frelka on 2012-06-11 18:46
I need a Goring Kerr Tek 21 manual.
➡️ Reply
#Graseby/Goring-Kerr by Adrian on 2009-10-08 10:22
I was wondering if you ever got a copy of this manual? I very am interested in the maintenance manual.I understand that the Anritsu KD7000 is the same machine?
➡️ Reply
#Graseby/Goring-Kerr by John Lindquist on 2010-04-14 16:43
I need a quote (price and delivery) on the drive and idler sprockets for the mattop belt on your unit # 72CS20INT, serial # 12873/3358. They have square bores and there are 15 0f them.Thank you.
➡️ Reply
#Graseby/Goring-Kerr by JOHN PUCELLA on 2008-06-01 20:37
I need an operating/illustration manual for Goring Kerr metal detector with band and nuematic reject system
➡️ Reply
#Graseby/Goring-Kerr by Joseph Cooney on 2019-09-25 20:49
Looking for the operational Manuals
➡️ Reply
#Graseby/Goring-Kerr by javier rivera on 2016-11-03 00:20
necesito comprar el manual de usuario del detector goring kerr tek dsp
➡️ Reply
#Graseby/Goring-Kerr by vic chiavola on 2008-06-13 15:26
I need an operating/Installation manual for a Graseby/Goreing-Kerr TEK-21 DSP Model Metal Detector.
➡️ Reply
#Graseby/Goring-Kerr by Isidro Servín on 2009-05-12 15:19
SERIAL : 46779 We need by PDF your instruction operation manual of our Graseby/Goring Kerr TEK DSP .21- Serial 46779Thank you in advance!!We have one units and need your operation manual asap. Preferable in Spanish. But if not, in English is fine.Sincerely,Isidro Servín.Santiago de Querétaro, Mexico…...
Show More
➡️ Reply
#Graseby/Goring-Kerr by Carlos Ortiz on 2006-08-05 14:36
Hi, We need new parts TK7951ISS.F rev. 1993 Display Board and TK7950 R.F. to Digital Board. What I need to do?
➡️ Reply
#Graseby/Goring-Kerr by Carsten on 2009-07-14 18:52
We have recently purchased a second hand Graseby Goring-Kerr Metal Detector, model DSP2. We did not receive an operating manual with the machine. It has been inspected, so we know it is functional, but we cannot have the computer programmed without the manual.Please advise if a manual is available o…...
Show More
➡️ Reply
#Graseby/Goring-Kerr by Edmundo Loyer on 2010-01-26 18:22
Dear Sirs:We own a goring metal detector but it has lost sensibility, so what I wantto know is were is the nearest place in south america that we can send itto be repaired. Thankyou in advance for your promt answer.Edmundo Loyer
➡️ Reply
#Graseby/Goring-Kerr by geffery on 2008-11-14 03:23
We have one Goring Kerr DSP2 metal detector with serial no 56467-1,we didn\'t use it for a long time.Now we want to set it up for a new product,we met problems to let it learn itself because nobady here know the password it.Could you please tell me the password of each level so I can access the sett…...
Show More
➡️ Reply
#Graseby/Goring-Kerr by Dennis Dahle on 2011-07-19 15:14
Good morning we have a TEK21DSP metal detector Is there anyway I could get some information on it. It has run beautifully for years and years but there is an issue right now (there is no signal) We changed the fuses. We just don\'t know what else to do. Thank you for your help Dennis
➡️ Reply
#Graseby/Goring-Kerr by timothy winkelkotter on 2008-03-04 23:42
I need a operation/maintenance manuel for a Goring Kerr DSP 2 metal detector. Where can I find one?
➡️ Reply
#Graseby/Goring-Kerr by Todd Flood on 2008-11-20 05:53
We need TEK DSP MODEL OPERATING MANUEL OF GORING KERR METAL DEDECTOR
➡️ Reply
#Graseby/Goring-Kerr by Rupender Rana on 2009-01-08 14:10
I have a problem with machine that is with calibrationwhen calibrate it in full calibration goes okay load cell gives proper output signal but again when try to do dynamic calibration its not gives any signal or value,,nothing happen on screen turn to weigh mode its shows the fault weigh plate is no…...
Show More
➡️ Reply
#Graseby/Goring-Kerr by nazeer ahmed on 2008-09-06 08:48
WE are leading manufacturers of biscuits in pakistan. we are facing problem at one of the units of mode s7683 metal detector machine as the touch panel has turned scrambled and no menu ia thus being shown on the screen.can you please advise at earliest to resolve this fatal problem.
➡️ Reply
#Graseby/Goring-Kerr by Jeffrey Amick on 2007-12-01 13:59
I need an operating/Installation manual for a Graseby/Goreing-Kerr TEK-DSP Model Metal Detector. There are two numbers associated with this unit, One on the digital readout (R1940607) and the other on a tag inside the metal detector head (51338-5) The unit works, but it is missing some parts. That i…...
Show More
➡️ Reply
#Graseby/Goring-Kerr by Orlando antillon muñoz on 2009-10-12 18:47
the reason for my post, is to ask the operations manual for our Graseby / Goring Kerr TEK DSP 21 Thanks in advance! We await your reply Sincerely: Deshidratadora Marata Chihuahua, Chihuahua. Mexico. Monday, 12 October 2009
➡️ Reply
#Graseby/Goring-Kerr by tho on 2009-11-17 19:23
We have second hand Goring Kerr metal detector DSP 2. Now we want to set it up for a new product,we met problems to let it learn itself because nobady here know the password it.Could you please tell me the password of each level ?Seed number : service : 45678123We wish receive your answerBest regard…...
Show More
➡️ Reply
#Graseby/Goring-Kerr by SWITU PATEL on 2009-04-05 05:26
We need TEK DSP MODEL OPERATING MANUEL OF GORING KERR METAL DEDECTOR
➡️ Reply
#Graseby/Goring-Kerr by Serkan ACAR on 2009-06-26 07:24
We have second hand Goring Kerr metal detector (but we dont know which model is this) with serial no 55358 Now we want to set it up for a new product,we met problems to let it learn itself because nobady here know the password it.Could you please tell me the password of each level so I can access th…...
Show More
➡️ Reply
#Graseby/Goring-Kerr by Edson Soares on 2009-03-02 16:35
I Need an operating manual for a Goring kerr DSP-2 to, Please answer me.
➡️ Reply
#Graseby/Goring-Kerr by greg waters on 2010-01-23 14:02
NEED TECHNICAL MANUAL
➡️ Reply
#Graseby/Goring-Kerr by JOE WYNN on 2011-08-18 14:16
I HAVE A GRASEBY GORING KERR DSP 2ON THE BOARD DP7916 (THE BOARD WITH THE BATTERY) I HAVE A PL10 AND A PL11. MY QUESTION IS THE RED AND BLACK WIRE CONNECTOR, I CAN NOT REMEMBER WHICH PL TO INSERT IT INTO? tHANKS FOR YOUR HELPJOE
➡️ Reply
#Graseby/Goring-Kerr by Bushra Latif on 2008-08-13 10:49
We has a Metal Dedector of Grasbey Goring KerrModel ....DSP 2 S.no .....56928-2110 v s/phase 50 HZ Full load 0.4Akindly inform us if you have its operating and instruction manual..Thanks And Regards Bushra Latif Asian Foods Industries Ltd
➡️ Reply
#Graseby/Goring-Kerr by Christian Torres Chilan on 2007-01-05 20:48
Good AfternoonSrs. Graseby/Goring KerrWe are the Company Farmayala. S.A. - Ecuador - Duran.We need to know and have instruction operation manual of your Graseby/Goring Kerr TEK DSP - Serial 50464Its commentaries awaiting Thanks so muchChristian Torres Chilan.Corporation Farmayala S.A.Engineer of Pro…...
Show More
➡️ Reply
#Graseby/Goring-Kerr by Jim on 2011-04-19 20:38
Did you get your manual? The Tektamet has 2 main circuit boards, power supply board has 2 LED\'s on it, red and green. Is this right?
➡️ Reply
#Graseby/Goring-Kerr by Jim on 2011-04-19 20:17
Try ( Z B Z B ) for the password. This may get you into the program so you can change it.
➡️ Reply
#Graseby/Goring-Kerr by Cristobal Perez on 2011-04-01 00:00
In my factory, I have a metal detector Graseby/Goring-Kerr, wihich Ican not to calibrate, because I don\'t have the password.I don\'t have the manual.Please, send the manual and the password to my email.Regards
➡️ Reply
#Graseby/Goring-Kerr by BEN AMEUR SAHBI on 2009-11-13 15:12
DEAR SIR , WE ASK SEND LIST PARTS OF METAL DETECTOR DSP-2 DATE 1997 /BEST REGARDS
➡️ Reply
#Graseby/Goring-Kerr by Nguyen Hung on 2008-04-21 03:17
I forgot password of DSP2, metal detectorpassword seed number:Operator: 12345678Supervisor:23456781Engineer: 34567812Service: 45678123Pls send me th passwordsBest regards
➡️ Reply
#Graseby/Goring-Kerr by Chris Grabarkievtz on 2010-01-27 17:20
My company had purchased 2 dsp2 metal detectors from an auction. We ordered the Operating and Instruction Manual. I need several parts just to get one of them working. I need the belt drive motor, a 7 pin harness from the motor to the control board, belting for the conveyor, also a wiring diagram wo…...
Show More
➡️ Reply
#Graseby/Goring-Kerr by Pedro Cabrera on 2011-04-14 23:54
Dear GentlemenI am working as a Project Engeneer in Britsh American Tobacco Operaciones Chile S.A. and I need the Set up and Operator Manual to put in service an old Goring Keer Metal Detector type TEK 2 serial number 43324. Please could you mind to help me sending the manuals?Awaiting your kindly r…...
Show More
➡️ Reply
#Graseby/Goring-Kerr by Juan Briseno on 2008-11-04 20:21
Hello, my name is Juan Briseno and I am a seller on Ebay (OB20_2). I got a hold of the following eqipment, and I was wondering if you were interested in buying them.3 Goring kerr TK7905 power supply board2 Goring Kerr DSP 1 control panel2 Goring Kerr DSP 2 control panel3 Goring Kerr DSP 3 control pa…...
Show More
➡️ Reply
#Graseby/Goring-Kerr by Tatjana on 2009-05-06 22:39
Hi Could you please provide us with an operational manual for Goring Kerr Tek 21 DSP.We could not locate it in the plant
➡️ Reply
#Graseby/Goring-Kerr by Delon Ogle on 2008-01-29 11:10
I am trying to locate an operating manual for a tek 21 dsp metal detecting device, serial no. 48796. I do have one but its in German
➡️ Reply
#Graseby/Goring-Kerr by Edson Soares on 2009-03-02 16:45
Hello Giorgio, can you help me?I need an operating manual for Metal Detector Goring Kerr DSP-2 to, you have?Please contact me.
➡️ Reply

Contact Us

🚑Shop Location🛠️

Industrial Electronic Repair
145 Rockwell Place Ct
Tobaccoville, NC 27050
🚑 Rush repair shipments only — no walk-ins.

📞Phone

1-336-969-0110

📦Mailing Address🚛

Industrial Electronic Repair
931-E S. Main St #204
Kernersville, NC 27284
📦 Mailing Address (for invoices or shipped repairs)
No walk-ins accepted.