Graseby/Goring-Kerr Service & Repair Forum

If you can send me a parts breakdown of dsp-2 goring kerr it will be appreciated greatly. Thanks, Matthew Lamontagne

— Posted by matthew lamontagne on 2009-12-21

Reply🗨️Ask a New Question Below❓


Recent Comments Search: "Graseby/Goring-Kerr"

If you need your Graseby/Goring-Kerr unit tested or repaired,
give us a call at 1-336-969-0110.
We offer free estimates and extended warranties on the work performed.
Shipping/Receiving:
Industrial Electronic Repair
145 Rockwell Place Ct
Tobaccoville, NC 27050
Phone: 1-336-969-0110

Recent 85 Comments

#Graseby/Goring-Kerr by vic chiavola on 2008-06-13 15:26
I need an operating/Installation manual for a Graseby/Goreing-Kerr TEK-21 DSP Model Metal Detector.
➡️ Reply
#Graseby/Goring-Kerr by Bushra Latif on 2008-08-13 10:49
We has a Metal Dedector of Grasbey Goring KerrModel ....DSP 2 S.no .....56928-2110 v s/phase 50 HZ Full load 0.4Akindly inform us if you have its operating and instruction manual..Thanks And Regards Bushra Latif Asian Foods Industries Ltd
➡️ Reply
#Graseby/Goring-Kerr by Jesus on 2010-09-09 21:31
There is a fault in a metalcheck goring kerr tek 21, the fault is \"search head\" I can\'t not enable this problem
➡️ Reply
#Graseby/Goring-Kerr by Delon Ogle on 2008-01-29 11:10
I am trying to locate an operating manual for a tek 21 dsp metal detecting device, serial no. 48796. I do have one but its in German
➡️ Reply
#Graseby/Goring-Kerr by Serkan ACAR on 2009-06-26 07:24
We have second hand Goring Kerr metal detector (but we dont know which model is this) with serial no 55358 Now we want to set it up for a new product,we met problems to let it learn itself because nobady here know the password it.Could you please tell me the password of each level so I can access th…...
Show More
➡️ Reply
#Graseby/Goring-Kerr by Chris Grabarkievtz on 2010-01-27 17:20
My company had purchased 2 dsp2 metal detectors from an auction. We ordered the Operating and Instruction Manual. I need several parts just to get one of them working. I need the belt drive motor, a 7 pin harness from the motor to the control board, belting for the conveyor, also a wiring diagram wo…...
Show More
➡️ Reply
#Graseby/Goring-Kerr by Juan Briseno on 2008-11-04 20:21
Hello, my name is Juan Briseno and I am a seller on Ebay (OB20_2). I got a hold of the following eqipment, and I was wondering if you were interested in buying them.3 Goring kerr TK7905 power supply board2 Goring Kerr DSP 1 control panel2 Goring Kerr DSP 2 control panel3 Goring Kerr DSP 3 control pa…...
Show More
➡️ Reply
#Graseby/Goring-Kerr by John Beddard on 2011-06-21 13:58
Can you supply a contact number in the uk so that we can get one of your technical people to look at our machineType 2022Serial number 56798-3Best regardsJohn Beddard
➡️ Reply
#Graseby/Goring-Kerr by Carsten on 2009-07-14 18:52
We have recently purchased a second hand Graseby Goring-Kerr Metal Detector, model DSP2. We did not receive an operating manual with the machine. It has been inspected, so we know it is functional, but we cannot have the computer programmed without the manual.Please advise if a manual is available o…...
Show More
➡️ Reply
#Graseby/Goring-Kerr by Ken Melech on 2008-10-23 23:24
We have recently purchased a second hand Graseby Goring-Kerr Metal Detector, model DSP2. We did not receive an operating manual with the machine. It has been inspected, so we know it is functional, but we cannot have the computer programmed without the manual.Please advise if a manual is available o…...
Show More
➡️ Reply
#Graseby/Goring-Kerr by John Lindquist on 2010-04-14 16:43
I need a quote (price and delivery) on the drive and idler sprockets for the mattop belt on your unit # 72CS20INT, serial # 12873/3358. They have square bores and there are 15 0f them.Thank you.
➡️ Reply
#Graseby/Goring-Kerr by Jesus Lamas on 2010-09-10 14:17
there is a fault \"search head\" I can not enable this fault.
➡️ Reply
#Graseby/Goring-Kerr by matthew lamontagne on 2009-12-21 05:27
If you can send me a parts breakdown of dsp-2 goring kerr it will be appreciated greatly. Thanks, Matthew Lamontagne
➡️ Reply
#Graseby/Goring-Kerr by Orlando antillon muñoz on 2009-10-12 18:47
the reason for my post, is to ask the operations manual for our Graseby / Goring Kerr TEK DSP 21 Thanks in advance! We await your reply Sincerely: Deshidratadora Marata Chihuahua, Chihuahua. Mexico. Monday, 12 October 2009
➡️ Reply
#Graseby/Goring-Kerr by JOE WYNN on 2011-08-18 14:16
I HAVE A GRASEBY GORING KERR DSP 2ON THE BOARD DP7916 (THE BOARD WITH THE BATTERY) I HAVE A PL10 AND A PL11. MY QUESTION IS THE RED AND BLACK WIRE CONNECTOR, I CAN NOT REMEMBER WHICH PL TO INSERT IT INTO? tHANKS FOR YOUR HELPJOE
➡️ Reply
#Graseby/Goring-Kerr by Byron Moran on 2012-11-06 15:36
DearsWe need price of metal detector with belt conveyor for cartons of frozen strawberries (-20°C) (10 kg). boxes measures are:500 mm X 500 mmThe metal detector will be at 18 °CBest regardsByron MoránSEVIND
➡️ Reply
#Graseby/Goring-Kerr by Isidro Servín on 2009-05-12 15:19
SERIAL : 46779 We need by PDF your instruction operation manual of our Graseby/Goring Kerr TEK DSP .21- Serial 46779Thank you in advance!!We have one units and need your operation manual asap. Preferable in Spanish. But if not, in English is fine.Sincerely,Isidro Servín.Santiago de Querétaro, Mexico…...
Show More
➡️ Reply
#Graseby/Goring-Kerr by Felix Bozo on 2009-04-13 15:04
Necesito Manual de operacion del Detector para metal Graseby - Goring Kerr \"TEC DSP\"
➡️ Reply
#Graseby/Goring-Kerr by Jose Luis Perez Contreras on 2011-11-25 19:34
Serian tan amables de venderme manual de usuario y o servicios del detector de metales Graseby/Goring-Kerr Tek DSP.Gracias por su atencion.Jose Luis Perez Contreras
➡️ Reply
#Graseby/Goring-Kerr by Jim on 2011-04-19 20:41
Hi, did you locate a manual?
➡️ Reply
#Graseby/Goring-Kerr by Rupender Rana on 2009-01-08 14:10
I have a problem with machine that is with calibrationwhen calibrate it in full calibration goes okay load cell gives proper output signal but again when try to do dynamic calibration its not gives any signal or value,,nothing happen on screen turn to weigh mode its shows the fault weigh plate is no…...
Show More
➡️ Reply
#Graseby/Goring-Kerr by Melissa Frelka on 2012-06-11 18:46
I need a Goring Kerr Tek 21 manual.
➡️ Reply
#Graseby/Goring-Kerr by Steve Brady on 2008-09-24 16:39
I am interested in purchasing manuals for a Greaseby/Goring Kerr metal detector. Model# DSP-2, Serial #22519, If you can help with this please respond. Thank you S. Brady
➡️ Reply
#Graseby/Goring-Kerr by sachin on 2011-09-20 10:26
Dear sir,we having TEK DSP Metal detector .Please send the calibration procedure of TEK DSP metal detector.Regards,Sachin
➡️ Reply
#Graseby/Goring-Kerr by VICTOR CHANG on 2011-06-26 15:38
Dear sir : We had bought a GRASEBY CHECKWEIGHER with type E30 , S/N: B56645, Date : 31-07-98, and found problems as follows recently 1. When product be put in load cell , the reading moves up and down and is unstable. 2. When trim calibration , we run prodct many times to weighing and found some of …...
Show More
➡️ Reply
#Graseby/Goring-Kerr by Dominic Patry on 2009-09-02 18:21
Hello,I\'m looking for a manual of a Graseby Goring/Kerr CDX 240 X-Ray machine. If you can sell me a copy of this manual.Thank you!
➡️ Reply
#Graseby/Goring-Kerr by serkan acar on 2009-06-26 07:16
We have 55358 serial metal dedectorsGraseby/Goring Kerr we need operation manuel and test partsBest regardsSultar Agriculture ProductsSerkan ACAR
➡️ Reply
#Graseby/Goring-Kerr by Pedro Cabrera on 2011-04-14 23:54
Dear GentlemenI am working as a Project Engeneer in Britsh American Tobacco Operaciones Chile S.A. and I need the Set up and Operator Manual to put in service an old Goring Keer Metal Detector type TEK 2 serial number 43324. Please could you mind to help me sending the manuals?Awaiting your kindly r…...
Show More
➡️ Reply
#Graseby/Goring-Kerr by Edson Soares on 2009-03-02 16:35
I Need an operating manual for a Goring kerr DSP-2 to, Please answer me.
➡️ Reply
#Graseby/Goring-Kerr by Giorgio Araujo on 2008-06-23 15:46
SERIAL : 48886 We need by PDF your instruction operation manual of your Graseby/Goring Kerr TEK DSP - Serial 48 886 110 volts.Thank you in advance!!We have two units and need your operation manual asap. Preferable in Spanish. But if not, in English is fine.Sincerely,Giorgio Araujo.Miami, FLA.
➡️ Reply
#Graseby/Goring-Kerr by christian on 2011-06-15 18:56
HelloI need a manual for a Goring Kerr DSP2.Can you help me?Best regardsFrode
➡️ Reply
#Graseby/Goring-Kerr by Cristobal Perez on 2011-04-01 00:00
In my factory, I have a metal detector Graseby/Goring-Kerr, wihich Ican not to calibrate, because I don\'t have the password.I don\'t have the manual.Please, send the manual and the password to my email.Regards
➡️ Reply
#Graseby/Goring-Kerr by Todd Flood on 2008-11-20 05:53
We need TEK DSP MODEL OPERATING MANUEL OF GORING KERR METAL DEDECTOR
➡️ Reply
#Graseby/Goring-Kerr by Jozef Granops on 2011-03-04 11:51
Iam looking for the representative in Poland of the Graseby /Goring Kerr metaldetector Type TEK 21
➡️ Reply
#Graseby/Goring-Kerr by SEMRA GÜMÜÞ on 2008-08-25 13:18
We need TEK DSP MODEL OPERATING MANUEL OF GORING KERR METAL DEDECTOR
➡️ Reply
#Graseby/Goring-Kerr by Charles Fultz on 2009-03-19 15:51
I have a few Goring Kerr boards for sale. I have some xt 7905, xt 7907 and xt 8908 if anyone is interesed in them. I would be willing to sell all for around the price of one board. There are about eight boards in all. We no longer have the machines and found boards left over. Respond to cfultz@chart…...
Show More
➡️ Reply
#Graseby/Goring-Kerr by Joseph Cooney on 2019-09-25 20:49
Looking for the operational Manuals
➡️ Reply
#Graseby/Goring-Kerr by Diversified Electronics on 2008-11-24 19:44
Dear SirsWe are in the buisness of servicing metal detectors and industrial electronics and one of customers has sent us a DSP-2 food production metal detector and would like us to provide a users manual for this unit.Can you help?ThanksTom Wood
➡️ Reply
#Graseby/Goring-Kerr by Suban Kotrbuppha on 2011-02-22 13:06
We need the manual of metal detector of GRASEBY GORING KERR model : TEK DSP (52528)Thank for your advance
➡️ Reply
#Graseby/Goring-Kerr by sameera abeysinghe on 2010-12-07 18:45
can you get me oparating manual of TEK21 machine.thanks.
➡️ Reply
#Graseby/Goring-Kerr by mario valente on 2009-03-31 14:37
I bought a used metal detector but have no manual, can you please find and send one to me. tks, regards,
➡️ Reply
#Graseby/Goring-Kerr by javier rivera on 2016-11-03 00:20
necesito comprar el manual de usuario del detector goring kerr tek dsp
➡️ Reply
#Graseby/Goring-Kerr by Carlos Ortiz on 2006-08-05 14:36
Hi, We need new parts TK7951ISS.F rev. 1993 Display Board and TK7950 R.F. to Digital Board. What I need to do?
➡️ Reply
#Graseby/Goring-Kerr by DARLENE CARTER on 2011-03-01 12:37
AM NEEDING MANUAL FOR MODEL 300 GORING-KERR. SER#17913/3tHANK YOU
➡️ Reply
#Graseby/Goring-Kerr by greg waters on 2010-01-23 14:02
NEED TECHNICAL MANUAL
➡️ Reply
#Graseby/Goring-Kerr by Irfan on 2009-12-29 08:17
We would like to have some technical details of Best checkweigher D30.
➡️ Reply
#Graseby/Goring-Kerr by BEN AMEUR SAHBI on 2009-11-13 15:12
DEAR SIR , WE ASK SEND LIST PARTS OF METAL DETECTOR DSP-2 DATE 1997 /BEST REGARDS
➡️ Reply
#Graseby/Goring-Kerr by VICTOR CHANG on 2011-07-01 10:37
Dear sir : We are Corner Corporation in Taiwan. We moved our Parmasol aerosol can line to Mainland China and found problems of E-30 checkweigher as follows : 1. The reading of weiight of single product goes up and down,is unstable. 2. When trim calibraton , there were some weight reading of product …...
Show More
➡️ Reply
#Graseby/Goring-Kerr by tho on 2009-11-17 19:23
We have second hand Goring Kerr metal detector DSP 2. Now we want to set it up for a new product,we met problems to let it learn itself because nobady here know the password it.Could you please tell me the password of each level ?Seed number : service : 45678123We wish receive your answerBest regard…...
Show More
➡️ Reply
#Graseby/Goring-Kerr by Tatjana on 2009-05-06 22:39
Hi Could you please provide us with an operational manual for Goring Kerr Tek 21 DSP.We could not locate it in the plant
➡️ Reply

Contact Us

🚑Shop Location🛠️

Industrial Electronic Repair
145 Rockwell Place Ct
Tobaccoville, NC 27050
🚑 Rush repair shipments only — no walk-ins.

📞Phone

1-336-969-0110

📦Mailing Address🚛

Industrial Electronic Repair
931-E S. Main St #204
Kernersville, NC 27284
📦 Mailing Address (for invoices or shipped repairs)
No walk-ins accepted.