Graseby/Goring-Kerr Service & Repair Forum

I need a operation/maintenance manuel for a Goring Kerr DSP 2 metal detector. Where can I find one?

— Posted by timothy winkelkotter on 2008-03-04

Reply🗨️Ask a New Question Below❓


Recent Comments Search: "Graseby/Goring-Kerr"

If you need your Graseby/Goring-Kerr unit tested or repaired,
give us a call at 1-336-969-0110.
We offer free estimates and extended warranties on the work performed.
Shipping/Receiving:
Industrial Electronic Repair
145 Rockwell Place Ct
Tobaccoville, NC 27050
Phone: 1-336-969-0110

Recent 85 Comments

#Graseby/Goring-Kerr by Delon Ogle on 2008-01-29 11:10
I am trying to locate an operating manual for a tek 21 dsp metal detecting device, serial no. 48796. I do have one but its in German
➡️ Reply
#Graseby/Goring-Kerr by Jim on 2011-04-19 20:33
Graseby G K no longer exists. The company that purchased them is Thermo Fisher Scientific. May be you could try that name in Poland. Good luck.
➡️ Reply
#Graseby/Goring-Kerr by timothy winkelkotter on 2008-03-04 23:42
I need a operation/maintenance manuel for a Goring Kerr DSP 2 metal detector. Where can I find one?
➡️ Reply
#Graseby/Goring-Kerr by Prakash Panchal on 2015-07-10 07:20
We required user manual for Graseby/goring Kerr Metal detector R-1940607.
➡️ Reply
#Graseby/Goring-Kerr by dean curbishley on 2007-07-28 15:29
we have TK7950 boards available, what frequency do you require?
➡️ Reply
#Graseby/Goring-Kerr by sameera abeysinghe on 2010-12-07 18:45
can you get me oparating manual of TEK21 machine.thanks.
➡️ Reply
#Graseby/Goring-Kerr by greg waters on 2010-01-23 14:02
NEED TECHNICAL MANUAL
➡️ Reply
#Graseby/Goring-Kerr by BEN AMEUR SAHBI on 2009-11-13 15:12
DEAR SIR , WE ASK SEND LIST PARTS OF METAL DETECTOR DSP-2 DATE 1997 /BEST REGARDS
➡️ Reply
#Graseby/Goring-Kerr by VICTOR CHANG on 2011-07-01 10:37
Dear sir : We are Corner Corporation in Taiwan. We moved our Parmasol aerosol can line to Mainland China and found problems of E-30 checkweigher as follows : 1. The reading of weiight of single product goes up and down,is unstable. 2. When trim calibraton , there were some weight reading of product …...
Show More
➡️ Reply
#Graseby/Goring-Kerr by Terri Beach on 2009-03-12 14:17
I am trying to get a manufacture spec sheet on a goring kerr tek dsp
➡️ Reply
#Graseby/Goring-Kerr by Giorgio Araujo on 2008-06-23 15:46
SERIAL : 48886 We need by PDF your instruction operation manual of your Graseby/Goring Kerr TEK DSP - Serial 48 886 110 volts.Thank you in advance!!We have two units and need your operation manual asap. Preferable in Spanish. But if not, in English is fine.Sincerely,Giorgio Araujo.Miami, FLA.
➡️ Reply
#Graseby/Goring-Kerr by RANDY P LAFORTEZA on 2011-06-16 19:46
i need a parts list for local start-stop button(the whole unit including box) for dsp3 metal detector.
➡️ Reply
#Graseby/Goring-Kerr by mario cardona on 2007-12-20 17:07
I have a problem with a graseby goring-ker dsp 2s, when I turned it on it makes a noise (alarm) and i can not quit this alarmI want to know if you know something about this problem because I do not have a manual to rapair this machine
➡️ Reply
#Graseby/Goring-Kerr by SWITU PATEL on 2009-04-05 05:26
We need TEK DSP MODEL OPERATING MANUEL OF GORING KERR METAL DEDECTOR
➡️ Reply
#Graseby/Goring-Kerr by Mayank Agarwal on 2009-04-13 10:05
Hi, This is Mayank from India(Makson\'s Nutrition),We posses a metal detactor by you,request you to send a manual for its operation. As it is not working properly.Serial No:4833RegardsMayank00919302611867
➡️ Reply
#Graseby/Goring-Kerr by matthew lamontagne on 2009-12-21 05:27
If you can send me a parts breakdown of dsp-2 goring kerr it will be appreciated greatly. Thanks, Matthew Lamontagne
➡️ Reply
#Graseby/Goring-Kerr by Carlos Ortiz on 2006-08-05 14:36
Hi, We need new parts TK7951ISS.F rev. 1993 Display Board and TK7950 R.F. to Digital Board. What I need to do?
➡️ Reply
#Graseby/Goring-Kerr by Suban Kotrbuppha on 2011-02-22 13:06
We need the manual of metal detector of GRASEBY GORING KERR model : TEK DSP (52528)Thank for your advance
➡️ Reply
#Graseby/Goring-Kerr by Chris Grabarkievtz on 2010-01-27 17:20
My company had purchased 2 dsp2 metal detectors from an auction. We ordered the Operating and Instruction Manual. I need several parts just to get one of them working. I need the belt drive motor, a 7 pin harness from the motor to the control board, belting for the conveyor, also a wiring diagram wo…...
Show More
➡️ Reply
#Graseby/Goring-Kerr by John Beddard on 2011-06-21 13:58
Can you supply a contact number in the uk so that we can get one of your technical people to look at our machineType 2022Serial number 56798-3Best regardsJohn Beddard
➡️ Reply
#Graseby/Goring-Kerr by Tatjana on 2009-05-06 22:39
Hi Could you please provide us with an operational manual for Goring Kerr Tek 21 DSP.We could not locate it in the plant
➡️ Reply
#Graseby/Goring-Kerr by JOHN PUCELLA on 2008-06-01 20:37
I need an operating/illustration manual for Goring Kerr metal detector with band and nuematic reject system
➡️ Reply
#Graseby/Goring-Kerr by Serkan ACAR on 2009-06-26 07:24
We have second hand Goring Kerr metal detector (but we dont know which model is this) with serial no 55358 Now we want to set it up for a new product,we met problems to let it learn itself because nobady here know the password it.Could you please tell me the password of each level so I can access th…...
Show More
➡️ Reply
#Graseby/Goring-Kerr by tho on 2009-11-17 19:23
We have second hand Goring Kerr metal detector DSP 2. Now we want to set it up for a new product,we met problems to let it learn itself because nobady here know the password it.Could you please tell me the password of each level ?Seed number : service : 45678123We wish receive your answerBest regard…...
Show More
➡️ Reply
#Graseby/Goring-Kerr by Jesus on 2010-09-09 21:31
There is a fault in a metalcheck goring kerr tek 21, the fault is \"search head\" I can\'t not enable this problem
➡️ Reply
#Graseby/Goring-Kerr by Joseph Cooney on 2019-09-25 20:49
Looking for the operational Manuals
➡️ Reply
#Graseby/Goring-Kerr by Jim on 2011-04-19 20:17
Try ( Z B Z B ) for the password. This may get you into the program so you can change it.
➡️ Reply
#Graseby/Goring-Kerr by Rupender Rana on 2009-01-08 14:10
I have a problem with machine that is with calibrationwhen calibrate it in full calibration goes okay load cell gives proper output signal but again when try to do dynamic calibration its not gives any signal or value,,nothing happen on screen turn to weigh mode its shows the fault weigh plate is no…...
Show More
➡️ Reply
#Graseby/Goring-Kerr by Jim on 2011-04-19 20:22
I don\'t know of a Model 300 unless it is a new one an Apex 300. With that number you have it sounds like an old Model called a Tektamet.
➡️ Reply
#Graseby/Goring-Kerr by Juan Briseno on 2008-11-04 20:21
Hello, my name is Juan Briseno and I am a seller on Ebay (OB20_2). I got a hold of the following eqipment, and I was wondering if you were interested in buying them.3 Goring kerr TK7905 power supply board2 Goring Kerr DSP 1 control panel2 Goring Kerr DSP 2 control panel3 Goring Kerr DSP 3 control pa…...
Show More
➡️ Reply
#Graseby/Goring-Kerr by Orlando antillon muñoz on 2009-10-12 18:47
the reason for my post, is to ask the operations manual for our Graseby / Goring Kerr TEK DSP 21 Thanks in advance! We await your reply Sincerely: Deshidratadora Marata Chihuahua, Chihuahua. Mexico. Monday, 12 October 2009
➡️ Reply
#Graseby/Goring-Kerr by Jesus Lamas on 2010-09-10 14:17
there is a fault \"search head\" I can not enable this fault.
➡️ Reply
#Graseby/Goring-Kerr by Melissa Frelka on 2012-06-11 18:46
I need a Goring Kerr Tek 21 manual.
➡️ Reply
#Graseby/Goring-Kerr by Charles Fultz on 2009-03-19 15:51
I have a few Goring Kerr boards for sale. I have some xt 7905, xt 7907 and xt 8908 if anyone is interesed in them. I would be willing to sell all for around the price of one board. There are about eight boards in all. We no longer have the machines and found boards left over. Respond to cfultz@chart…...
Show More
➡️ Reply
#Graseby/Goring-Kerr by Laura Machin on 2009-01-13 12:01
Srs. Graseby/Goring KerrI´m Laura Machin from Solvay pharma company. We are looking for the TSK DSP metal detector oparating manual. Maybe you can help us.Thank you.
➡️ Reply
#Graseby/Goring-Kerr by Dean Curbishley on 2012-08-27 13:38
pass code is ZBZB
➡️ Reply
#Graseby/Goring-Kerr by JOE WYNN on 2011-08-18 14:16
I HAVE A GRASEBY GORING KERR DSP 2ON THE BOARD DP7916 (THE BOARD WITH THE BATTERY) I HAVE A PL10 AND A PL11. MY QUESTION IS THE RED AND BLACK WIRE CONNECTOR, I CAN NOT REMEMBER WHICH PL TO INSERT IT INTO? tHANKS FOR YOUR HELPJOE
➡️ Reply
#Graseby/Goring-Kerr by VICTOR CHANG on 2011-06-26 15:38
Dear sir : We had bought a GRASEBY CHECKWEIGHER with type E30 , S/N: B56645, Date : 31-07-98, and found problems as follows recently 1. When product be put in load cell , the reading moves up and down and is unstable. 2. When trim calibration , we run prodct many times to weighing and found some of …...
Show More
➡️ Reply
#Graseby/Goring-Kerr by Kornelia Degorska on 2012-09-05 10:11
I\'ve lost password of DSP2, metal detectorpassword seed number:Operator: 12345678Supervisor:23456781Engineer: 34567812Service: 45678123Please send me the passwordsBest regardsKornelia.
➡️ Reply
#Graseby/Goring-Kerr by Doug Thompson on 2012-09-06 02:59
Hi Joe, did you ever get a response to your query on this or figure it out? I currently have the same problem. Any help would be much appreciated.Kind RegardsDoug
➡️ Reply
#Graseby/Goring-Kerr by Dennis Dahle on 2011-07-19 15:14
Good morning we have a TEK21DSP metal detector Is there anyway I could get some information on it. It has run beautifully for years and years but there is an issue right now (there is no signal) We changed the fuses. We just don\'t know what else to do. Thank you for your help Dennis
➡️ Reply
#Graseby/Goring-Kerr by Frode Arntsen on 2010-01-05 09:14
HelloI need a manual for a Goring Kerr DSP2.Can you help me?Best regardsFrode
➡️ Reply
#Graseby/Goring-Kerr by Brian Large on 2009-01-21 15:54
I have a Graseby Goring Kerr metal detectorMD: 60ALINTKSer: 10531/3046I am looking for any manuals that are available for this machine.Thank you,Brian LargePacific Foods19480 SW 97th Ave.Tualatin, OR 97062503 692-9666 ext. 1417Cell 971 218-5147
➡️ Reply
#Graseby/Goring-Kerr by nazeer ahmed on 2008-09-06 08:48
WE are leading manufacturers of biscuits in pakistan. we are facing problem at one of the units of mode s7683 metal detector machine as the touch panel has turned scrambled and no menu ia thus being shown on the screen.can you please advise at earliest to resolve this fatal problem.
➡️ Reply
#Graseby/Goring-Kerr by serkan acar on 2009-06-26 07:16
We have 55358 serial metal dedectorsGraseby/Goring Kerr we need operation manuel and test partsBest regardsSultar Agriculture ProductsSerkan ACAR
➡️ Reply
#Graseby/Goring-Kerr by Nguyen Hung on 2008-04-21 03:17
I forgot password of DSP2, metal detectorpassword seed number:Operator: 12345678Supervisor:23456781Engineer: 34567812Service: 45678123Pls send me th passwordsBest regards
➡️ Reply
#Graseby/Goring-Kerr by Jozef Granops on 2011-03-04 11:51
Iam looking for the representative in Poland of the Graseby /Goring Kerr metaldetector Type TEK 21
➡️ Reply
#Graseby/Goring-Kerr by Steve Brady on 2008-09-24 16:39
I am interested in purchasing manuals for a Greaseby/Goring Kerr metal detector. Model# DSP-2, Serial #22519, If you can help with this please respond. Thank you S. Brady
➡️ Reply
#Graseby/Goring-Kerr by DARLENE CARTER on 2011-03-01 12:37
AM NEEDING MANUAL FOR MODEL 300 GORING-KERR. SER#17913/3tHANK YOU
➡️ Reply
#Graseby/Goring-Kerr by Lisa on 2008-11-14 19:56
I need an operatin gmanual for a Graseby/Goring-Kerr DSP-2 CONTROL. Do you have one available? PLease advise.
➡️ Reply

Contact Us

🚑Shop Location🛠️

Industrial Electronic Repair
145 Rockwell Place Ct
Tobaccoville, NC 27050
🚑 Rush repair shipments only — no walk-ins.

📞Phone

1-336-969-0110

📦Mailing Address🚛

Industrial Electronic Repair
931-E S. Main St #204
Kernersville, NC 27284
📦 Mailing Address (for invoices or shipped repairs)
No walk-ins accepted.