Graseby/Goring-Kerr Service & Repair Forum

We would like to have some technical details of Best checkweigher D30.

— Posted by Irfan on 2009-12-29

Reply🗨️Ask a New Question Below❓


Recent Comments Search: "Graseby/Goring-Kerr"

If you need your Graseby/Goring-Kerr unit tested or repaired,
give us a call at 1-336-969-0110.
We offer free estimates and extended warranties on the work performed.
Shipping/Receiving:
Industrial Electronic Repair
145 Rockwell Place Ct
Tobaccoville, NC 27050
Phone: 1-336-969-0110

Recent 85 Comments

#Graseby/Goring-Kerr by BEN AMEUR SAHBI on 2009-11-13 15:12
DEAR SIR , WE ASK SEND LIST PARTS OF METAL DETECTOR DSP-2 DATE 1997 /BEST REGARDS
➡️ Reply
#Graseby/Goring-Kerr by Kornelia Degorska on 2012-09-05 10:11
I\'ve lost password of DSP2, metal detectorpassword seed number:Operator: 12345678Supervisor:23456781Engineer: 34567812Service: 45678123Please send me the passwordsBest regardsKornelia.
➡️ Reply
#Graseby/Goring-Kerr by VICTOR CHANG on 2011-06-26 15:38
Dear sir : We had bought a GRASEBY CHECKWEIGHER with type E30 , S/N: B56645, Date : 31-07-98, and found problems as follows recently 1. When product be put in load cell , the reading moves up and down and is unstable. 2. When trim calibration , we run prodct many times to weighing and found some of …...
Show More
➡️ Reply
#Graseby/Goring-Kerr by ourang on 2009-02-25 09:34
Dear Sr or MadamThis is Ourang Batmanghlich from solico meat product.I am technical manager.We have a check weigher machin from GRASEBY type BEST D30.we need user manual this machin.Please send me .Tank you
➡️ Reply
#Graseby/Goring-Kerr by timothy winkelkotter on 2008-03-04 23:42
I need a operation/maintenance manuel for a Goring Kerr DSP 2 metal detector. Where can I find one?
➡️ Reply
#Graseby/Goring-Kerr by Melissa Frelka on 2012-06-11 18:46
I need a Goring Kerr Tek 21 manual.
➡️ Reply
#Graseby/Goring-Kerr by Christian Torres Chilan on 2007-01-05 20:48
Good AfternoonSrs. Graseby/Goring KerrWe are the Company Farmayala. S.A. - Ecuador - Duran.We need to know and have instruction operation manual of your Graseby/Goring Kerr TEK DSP - Serial 50464Its commentaries awaiting Thanks so muchChristian Torres Chilan.Corporation Farmayala S.A.Engineer of Pro…...
Show More
➡️ Reply
#Graseby/Goring-Kerr by JOE WYNN on 2011-08-18 14:16
I HAVE A GRASEBY GORING KERR DSP 2ON THE BOARD DP7916 (THE BOARD WITH THE BATTERY) I HAVE A PL10 AND A PL11. MY QUESTION IS THE RED AND BLACK WIRE CONNECTOR, I CAN NOT REMEMBER WHICH PL TO INSERT IT INTO? tHANKS FOR YOUR HELPJOE
➡️ Reply
#Graseby/Goring-Kerr by Orlando antillon muñoz on 2009-10-12 18:47
the reason for my post, is to ask the operations manual for our Graseby / Goring Kerr TEK DSP 21 Thanks in advance! We await your reply Sincerely: Deshidratadora Marata Chihuahua, Chihuahua. Mexico. Monday, 12 October 2009
➡️ Reply
#Graseby/Goring-Kerr by Brian Large on 2009-01-21 15:54
I have a Graseby Goring Kerr metal detectorMD: 60ALINTKSer: 10531/3046I am looking for any manuals that are available for this machine.Thank you,Brian LargePacific Foods19480 SW 97th Ave.Tualatin, OR 97062503 692-9666 ext. 1417Cell 971 218-5147
➡️ Reply
#Graseby/Goring-Kerr by Prakash Panchal on 2015-07-10 07:20
We required user manual for Graseby/goring Kerr Metal detector R-1940607.
➡️ Reply
#Graseby/Goring-Kerr by Edson Soares on 2009-03-02 16:45
Hello Giorgio, can you help me?I need an operating manual for Metal Detector Goring Kerr DSP-2 to, you have?Please contact me.
➡️ Reply
#Graseby/Goring-Kerr by Jim on 2011-04-19 20:41
Hi, did you locate a manual?
➡️ Reply
#Graseby/Goring-Kerr by Suban Kotrbuppha on 2011-02-22 13:06
We need the manual of metal detector of GRASEBY GORING KERR model : TEK DSP (52528)Thank for your advance
➡️ Reply
#Graseby/Goring-Kerr by nazeer ahmed on 2008-09-06 08:48
WE are leading manufacturers of biscuits in pakistan. we are facing problem at one of the units of mode s7683 metal detector machine as the touch panel has turned scrambled and no menu ia thus being shown on the screen.can you please advise at earliest to resolve this fatal problem.
➡️ Reply
#Graseby/Goring-Kerr by christian on 2011-06-15 18:56
HelloI need a manual for a Goring Kerr DSP2.Can you help me?Best regardsFrode
➡️ Reply
#Graseby/Goring-Kerr by Dean Curbishley on 2012-08-27 13:38
pass code is ZBZB
➡️ Reply
#Graseby/Goring-Kerr by Laura Machin on 2009-01-13 12:01
Srs. Graseby/Goring KerrI´m Laura Machin from Solvay pharma company. We are looking for the TSK DSP metal detector oparating manual. Maybe you can help us.Thank you.
➡️ Reply
#Graseby/Goring-Kerr by mario cardona on 2007-12-20 17:07
I have a problem with a graseby goring-ker dsp 2s, when I turned it on it makes a noise (alarm) and i can not quit this alarmI want to know if you know something about this problem because I do not have a manual to rapair this machine
➡️ Reply
#Graseby/Goring-Kerr by Joseph Cooney on 2019-09-25 20:49
Looking for the operational Manuals
➡️ Reply
#Graseby/Goring-Kerr by Jesus Lamas on 2010-09-10 14:17
there is a fault \"search head\" I can not enable this fault.
➡️ Reply
#Graseby/Goring-Kerr by Felix Bozo on 2009-04-13 15:04
Necesito Manual de operacion del Detector para metal Graseby - Goring Kerr \"TEC DSP\"
➡️ Reply
#Graseby/Goring-Kerr by Carsten on 2009-07-14 18:52
We have recently purchased a second hand Graseby Goring-Kerr Metal Detector, model DSP2. We did not receive an operating manual with the machine. It has been inspected, so we know it is functional, but we cannot have the computer programmed without the manual.Please advise if a manual is available o…...
Show More
➡️ Reply
#Graseby/Goring-Kerr by RANDY P LAFORTEZA on 2011-06-16 19:46
i need a parts list for local start-stop button(the whole unit including box) for dsp3 metal detector.
➡️ Reply
#Graseby/Goring-Kerr by Rupender Rana on 2009-01-08 14:10
I have a problem with machine that is with calibrationwhen calibrate it in full calibration goes okay load cell gives proper output signal but again when try to do dynamic calibration its not gives any signal or value,,nothing happen on screen turn to weigh mode its shows the fault weigh plate is no…...
Show More
➡️ Reply
#Graseby/Goring-Kerr by Jim on 2011-04-19 20:22
I don\'t know of a Model 300 unless it is a new one an Apex 300. With that number you have it sounds like an old Model called a Tektamet.
➡️ Reply
#Graseby/Goring-Kerr by Bushra Latif on 2008-08-13 10:49
We has a Metal Dedector of Grasbey Goring KerrModel ....DSP 2 S.no .....56928-2110 v s/phase 50 HZ Full load 0.4Akindly inform us if you have its operating and instruction manual..Thanks And Regards Bushra Latif Asian Foods Industries Ltd
➡️ Reply
#Graseby/Goring-Kerr by Byron Moran on 2012-11-06 15:36
DearsWe need price of metal detector with belt conveyor for cartons of frozen strawberries (-20°C) (10 kg). boxes measures are:500 mm X 500 mmThe metal detector will be at 18 °CBest regardsByron MoránSEVIND
➡️ Reply
#Graseby/Goring-Kerr by Delon Ogle on 2008-01-29 11:10
I am trying to locate an operating manual for a tek 21 dsp metal detecting device, serial no. 48796. I do have one but its in German
➡️ Reply
#Graseby/Goring-Kerr by sameera abeysinghe on 2010-12-07 18:45
can you get me oparating manual of TEK21 machine.thanks.
➡️ Reply
#Graseby/Goring-Kerr by Jim on 2011-04-19 20:38
Did you get your manual? The Tektamet has 2 main circuit boards, power supply board has 2 LED\'s on it, red and green. Is this right?
➡️ Reply
#Graseby/Goring-Kerr by Tatjana on 2009-05-06 22:39
Hi Could you please provide us with an operational manual for Goring Kerr Tek 21 DSP.We could not locate it in the plant
➡️ Reply
#Graseby/Goring-Kerr by Irfan on 2009-12-29 08:17
We would like to have some technical details of Best checkweigher D30.
➡️ Reply
#Graseby/Goring-Kerr by DARLENE CARTER on 2011-03-01 12:37
AM NEEDING MANUAL FOR MODEL 300 GORING-KERR. SER#17913/3tHANK YOU
➡️ Reply
#Graseby/Goring-Kerr by John Lindquist on 2010-04-14 16:43
I need a quote (price and delivery) on the drive and idler sprockets for the mattop belt on your unit # 72CS20INT, serial # 12873/3358. They have square bores and there are 15 0f them.Thank you.
➡️ Reply
#Graseby/Goring-Kerr by greg waters on 2010-01-23 14:02
NEED TECHNICAL MANUAL
➡️ Reply
#Graseby/Goring-Kerr by Carlos Ortiz on 2006-08-05 14:36
Hi, We need new parts TK7951ISS.F rev. 1993 Display Board and TK7950 R.F. to Digital Board. What I need to do?
➡️ Reply
#Graseby/Goring-Kerr by Jose Luis Perez Contreras on 2011-11-25 19:34
Serian tan amables de venderme manual de usuario y o servicios del detector de metales Graseby/Goring-Kerr Tek DSP.Gracias por su atencion.Jose Luis Perez Contreras
➡️ Reply
#Graseby/Goring-Kerr by Edmundo Loyer on 2010-01-26 18:22
Dear Sirs:We own a goring metal detector but it has lost sensibility, so what I wantto know is were is the nearest place in south america that we can send itto be repaired. Thankyou in advance for your promt answer.Edmundo Loyer
➡️ Reply
#Graseby/Goring-Kerr by Jim on 2011-04-19 20:17
Try ( Z B Z B ) for the password. This may get you into the program so you can change it.
➡️ Reply
#Graseby/Goring-Kerr by Ron Giesbrecht on 2009-06-24 22:07
I recently bought a used GK DSP 2. Do you know where i could get an owners manual?Thanks
➡️ Reply
#Graseby/Goring-Kerr by Dennis Dahle on 2011-07-19 15:14
Good morning we have a TEK21DSP metal detector Is there anyway I could get some information on it. It has run beautifully for years and years but there is an issue right now (there is no signal) We changed the fuses. We just don\'t know what else to do. Thank you for your help Dennis
➡️ Reply
#Graseby/Goring-Kerr by Cristobal Perez on 2011-04-01 00:00
In my factory, I have a metal detector Graseby/Goring-Kerr, wihich Ican not to calibrate, because I don\'t have the password.I don\'t have the manual.Please, send the manual and the password to my email.Regards
➡️ Reply
#Graseby/Goring-Kerr by rob on 2011-06-30 17:59
Call Malcolm at DRM Weighparts on 44 (0)1527 558899 tell him Rob passed on his contact details. I n the meantime I have a few bits and pieces myself having been in th egame for a number of years e-mail me if you have any requirements I will check out what I have got.
➡️ Reply
#Graseby/Goring-Kerr by Diversified Electronics on 2008-11-24 19:44
Dear SirsWe are in the buisness of servicing metal detectors and industrial electronics and one of customers has sent us a DSP-2 food production metal detector and would like us to provide a users manual for this unit.Can you help?ThanksTom Wood
➡️ Reply
#Graseby/Goring-Kerr by dean curbishley on 2007-07-28 15:29
we have TK7950 boards available, what frequency do you require?
➡️ Reply
#Graseby/Goring-Kerr by Mayank Agarwal on 2009-04-13 10:05
Hi, This is Mayank from India(Makson\'s Nutrition),We posses a metal detactor by you,request you to send a manual for its operation. As it is not working properly.Serial No:4833RegardsMayank00919302611867
➡️ Reply
#Graseby/Goring-Kerr by vic chiavola on 2008-06-13 15:26
I need an operating/Installation manual for a Graseby/Goreing-Kerr TEK-21 DSP Model Metal Detector.
➡️ Reply
#Graseby/Goring-Kerr by Todd Flood on 2008-11-20 05:53
We need TEK DSP MODEL OPERATING MANUEL OF GORING KERR METAL DEDECTOR
➡️ Reply
#Graseby/Goring-Kerr by Lisa on 2008-11-14 19:56
I need an operatin gmanual for a Graseby/Goring-Kerr DSP-2 CONTROL. Do you have one available? PLease advise.
➡️ Reply

Contact Us

🚑Shop Location🛠️

Industrial Electronic Repair
145 Rockwell Place Ct
Tobaccoville, NC 27050
🚑 Rush repair shipments only — no walk-ins.

📞Phone

1-336-969-0110

📦Mailing Address🚛

Industrial Electronic Repair
931-E S. Main St #204
Kernersville, NC 27284
📦 Mailing Address (for invoices or shipped repairs)
No walk-ins accepted.