Graseby/Goring-Kerr Service & Repair Forum

I have a problem with machine that is with calibrationwhen calibrate it in full calibration goes okay load cell gives proper output signal but again when try to do dynamic calibration its not gives any signal or value,,nothing happen on screen turn to weigh mode its shows the fault weigh plate is not cleared

— Posted by Rupender Rana on 2009-01-08

Reply🗨️Ask a New Question Below❓


Recent Comments Search: "Graseby/Goring-Kerr"

If you need your Graseby/Goring-Kerr unit tested or repaired,
give us a call at 1-336-969-0110.
Estimates are free with an approved repair. Declined or unrepairable units are subject to a $75 evaluation, handling, and standard return-shipping fee. Extended warranties may be available.
Shipping/Receiving:
Industrial Electronic Repair
124 Five Forks Dr PMB #208
King, NC 27021
Phone: 1-336-969-0110

Recent 85 Comments

#Graseby/Goring-Kerr by Chris Grabarkievtz on 2010-01-27 17:20
My company had purchased 2 dsp2 metal detectors from an auction. We ordered the Operating and Instruction Manual. I need several parts just to get one of them working. I need the belt drive motor, a 7 pin harness from the motor to the control board, belting for the conveyor, also a wiring diagram wo…...
Show More
➡️ Reply
#Graseby/Goring-Kerr by Jesus on 2010-09-09 21:31
There is a fault in a metalcheck goring kerr tek 21, the fault is \"search head\" I can\'t not enable this problem
➡️ Reply
#Graseby/Goring-Kerr by Isidro Servín on 2009-05-12 15:19
SERIAL : 46779 We need by PDF your instruction operation manual of our Graseby/Goring Kerr TEK DSP .21- Serial 46779Thank you in advance!!We have one units and need your operation manual asap. Preferable in Spanish. But if not, in English is fine.Sincerely,Isidro Servín.Santiago de Querétaro, Mexico…...
Show More
➡️ Reply
#Graseby/Goring-Kerr by VICTOR CHANG on 2011-06-26 15:38
Dear sir : We had bought a GRASEBY CHECKWEIGHER with type E30 , S/N: B56645, Date : 31-07-98, and found problems as follows recently 1. When product be put in load cell , the reading moves up and down and is unstable. 2. When trim calibration , we run prodct many times to weighing and found some of …...
Show More
➡️ Reply
#Graseby/Goring-Kerr by SEMRA GÜMÜÞ on 2008-08-25 13:18
We need TEK DSP MODEL OPERATING MANUEL OF GORING KERR METAL DEDECTOR
➡️ Reply
#Graseby/Goring-Kerr by Dennis Dahle on 2011-07-19 15:14
Good morning we have a TEK21DSP metal detector Is there anyway I could get some information on it. It has run beautifully for years and years but there is an issue right now (there is no signal) We changed the fuses. We just don\'t know what else to do. Thank you for your help Dennis
➡️ Reply
#Graseby/Goring-Kerr by Charles Fultz on 2009-03-19 15:51
I have a few Goring Kerr boards for sale. I have some xt 7905, xt 7907 and xt 8908 if anyone is interesed in them. I would be willing to sell all for around the price of one board. There are about eight boards in all. We no longer have the machines and found boards left over. Respond to cfultz@chart…...
Show More
➡️ Reply
#Graseby/Goring-Kerr by greg waters on 2010-01-23 14:02
NEED TECHNICAL MANUAL
➡️ Reply
#Graseby/Goring-Kerr by Brian Large on 2009-01-21 15:54
I have a Graseby Goring Kerr metal detectorMD: 60ALINTKSer: 10531/3046I am looking for any manuals that are available for this machine.Thank you,Brian LargePacific Foods19480 SW 97th Ave.Tualatin, OR 97062503 692-9666 ext. 1417Cell 971 218-5147
➡️ Reply
#Graseby/Goring-Kerr by matthew lamontagne on 2009-12-21 05:27
If you can send me a parts breakdown of dsp-2 goring kerr it will be appreciated greatly. Thanks, Matthew Lamontagne
➡️ Reply
#Graseby/Goring-Kerr by vic chiavola on 2008-06-13 15:26
I need an operating/Installation manual for a Graseby/Goreing-Kerr TEK-21 DSP Model Metal Detector.
➡️ Reply
#Graseby/Goring-Kerr by Lisa on 2008-11-14 19:56
I need an operatin gmanual for a Graseby/Goring-Kerr DSP-2 CONTROL. Do you have one available? PLease advise.
➡️ Reply
#Graseby/Goring-Kerr by Dominic Patry on 2009-09-02 18:21
Hello,I\'m looking for a manual of a Graseby Goring/Kerr CDX 240 X-Ray machine. If you can sell me a copy of this manual.Thank you!
➡️ Reply
#Graseby/Goring-Kerr by Mark on 2011-05-25 16:00
Does anybody know the special password required for the system config ?
➡️ Reply
#Graseby/Goring-Kerr by DARLENE CARTER on 2011-03-01 12:37
AM NEEDING MANUAL FOR MODEL 300 GORING-KERR. SER#17913/3tHANK YOU
➡️ Reply
#Graseby/Goring-Kerr by Frode Arntsen on 2010-01-05 09:14
HelloI need a manual for a Goring Kerr DSP2.Can you help me?Best regardsFrode
➡️ Reply
#Graseby/Goring-Kerr by Mayank Agarwal on 2009-04-13 10:05
Hi, This is Mayank from India(Makson\'s Nutrition),We posses a metal detactor by you,request you to send a manual for its operation. As it is not working properly.Serial No:4833RegardsMayank00919302611867
➡️ Reply
#Graseby/Goring-Kerr by Orlando antillon muñoz on 2009-10-12 18:47
the reason for my post, is to ask the operations manual for our Graseby / Goring Kerr TEK DSP 21 Thanks in advance! We await your reply Sincerely: Deshidratadora Marata Chihuahua, Chihuahua. Mexico. Monday, 12 October 2009
➡️ Reply
#Graseby/Goring-Kerr by Prakash Panchal on 2015-07-10 07:20
We required user manual for Graseby/goring Kerr Metal detector R-1940607.
➡️ Reply
#Graseby/Goring-Kerr by sameera abeysinghe on 2010-12-07 18:45
can you get me oparating manual of TEK21 machine.thanks.
➡️ Reply
#Graseby/Goring-Kerr by VICTOR CHANG on 2011-07-01 10:37
Dear sir : We are Corner Corporation in Taiwan. We moved our Parmasol aerosol can line to Mainland China and found problems of E-30 checkweigher as follows : 1. The reading of weiight of single product goes up and down,is unstable. 2. When trim calibraton , there were some weight reading of product …...
Show More
➡️ Reply
#Graseby/Goring-Kerr by Ron Giesbrecht on 2009-06-24 22:07
I recently bought a used GK DSP 2. Do you know where i could get an owners manual?Thanks
➡️ Reply
#Graseby/Goring-Kerr by Suban Kotrbuppha on 2011-02-22 13:06
We need the manual of metal detector of GRASEBY GORING KERR model : TEK DSP (52528)Thank for your advance
➡️ Reply
#Graseby/Goring-Kerr by Giorgio Araujo on 2008-06-23 15:46
SERIAL : 48886 We need by PDF your instruction operation manual of your Graseby/Goring Kerr TEK DSP - Serial 48 886 110 volts.Thank you in advance!!We have two units and need your operation manual asap. Preferable in Spanish. But if not, in English is fine.Sincerely,Giorgio Araujo.Miami, FLA.
➡️ Reply
#Graseby/Goring-Kerr by Edmundo Loyer on 2010-01-26 18:22
Dear Sirs:We own a goring metal detector but it has lost sensibility, so what I wantto know is were is the nearest place in south america that we can send itto be repaired. Thankyou in advance for your promt answer.Edmundo Loyer
➡️ Reply
#Graseby/Goring-Kerr by Ken Melech on 2008-10-23 23:24
We have recently purchased a second hand Graseby Goring-Kerr Metal Detector, model DSP2. We did not receive an operating manual with the machine. It has been inspected, so we know it is functional, but we cannot have the computer programmed without the manual.Please advise if a manual is available o…...
Show More
➡️ Reply
#Graseby/Goring-Kerr by BEN AMEUR SAHBI on 2009-11-13 15:12
DEAR SIR , WE ASK SEND LIST PARTS OF METAL DETECTOR DSP-2 DATE 1997 /BEST REGARDS
➡️ Reply
#Graseby/Goring-Kerr by nazeer ahmed on 2008-09-06 08:48
WE are leading manufacturers of biscuits in pakistan. we are facing problem at one of the units of mode s7683 metal detector machine as the touch panel has turned scrambled and no menu ia thus being shown on the screen.can you please advise at earliest to resolve this fatal problem.
➡️ Reply
#Graseby/Goring-Kerr by timothy winkelkotter on 2008-03-04 23:42
I need a operation/maintenance manuel for a Goring Kerr DSP 2 metal detector. Where can I find one?
➡️ Reply
#Graseby/Goring-Kerr by Serkan ACAR on 2009-06-26 07:24
We have second hand Goring Kerr metal detector (but we dont know which model is this) with serial no 55358 Now we want to set it up for a new product,we met problems to let it learn itself because nobady here know the password it.Could you please tell me the password of each level so I can access th…...
Show More
➡️ Reply
#Graseby/Goring-Kerr by sachin on 2011-09-20 10:26
Dear sir,we having TEK DSP Metal detector .Please send the calibration procedure of TEK DSP metal detector.Regards,Sachin
➡️ Reply
#Graseby/Goring-Kerr by Delon Ogle on 2008-01-29 11:10
I am trying to locate an operating manual for a tek 21 dsp metal detecting device, serial no. 48796. I do have one but its in German
➡️ Reply
#Graseby/Goring-Kerr by Diversified Electronics on 2008-11-24 19:44
Dear SirsWe are in the buisness of servicing metal detectors and industrial electronics and one of customers has sent us a DSP-2 food production metal detector and would like us to provide a users manual for this unit.Can you help?ThanksTom Wood
➡️ Reply
#Graseby/Goring-Kerr by JOHN PUCELLA on 2008-06-01 20:37
I need an operating/illustration manual for Goring Kerr metal detector with band and nuematic reject system
➡️ Reply
#Graseby/Goring-Kerr by Rupender Rana on 2009-01-08 14:10
I have a problem with machine that is with calibrationwhen calibrate it in full calibration goes okay load cell gives proper output signal but again when try to do dynamic calibration its not gives any signal or value,,nothing happen on screen turn to weigh mode its shows the fault weigh plate is no…...
Show More
➡️ Reply
#Graseby/Goring-Kerr by Steve Brady on 2008-09-24 16:39
I am interested in purchasing manuals for a Greaseby/Goring Kerr metal detector. Model# DSP-2, Serial #22519, If you can help with this please respond. Thank you S. Brady
➡️ Reply
#Graseby/Goring-Kerr by Jim on 2011-04-19 20:41
Hi, did you locate a manual?
➡️ Reply
#Graseby/Goring-Kerr by Edson Soares on 2009-03-02 16:45
Hello Giorgio, can you help me?I need an operating manual for Metal Detector Goring Kerr DSP-2 to, you have?Please contact me.
➡️ Reply
#Graseby/Goring-Kerr by christian on 2011-06-15 18:56
HelloI need a manual for a Goring Kerr DSP2.Can you help me?Best regardsFrode
➡️ Reply
#Graseby/Goring-Kerr by Nasir hamalawey on 2009-07-01 06:40
i have a fault in metal detector DSP2 serial No:58464-1i need operation manual (english).i am ready to pay money for the manualThanksNasir
➡️ Reply
#Graseby/Goring-Kerr by Jim on 2011-04-19 20:38
Did you get your manual? The Tektamet has 2 main circuit boards, power supply board has 2 LED\'s on it, red and green. Is this right?
➡️ Reply
#Graseby/Goring-Kerr by Laura Machin on 2009-01-13 12:01
Srs. Graseby/Goring KerrI´m Laura Machin from Solvay pharma company. We are looking for the TSK DSP metal detector oparating manual. Maybe you can help us.Thank you.
➡️ Reply
#Graseby/Goring-Kerr by RANDY P LAFORTEZA on 2011-06-16 19:46
i need a parts list for local start-stop button(the whole unit including box) for dsp3 metal detector.
➡️ Reply
#Graseby/Goring-Kerr by Kornelia Degorska on 2012-09-05 10:11
I\'ve lost password of DSP2, metal detectorpassword seed number:Operator: 12345678Supervisor:23456781Engineer: 34567812Service: 45678123Please send me the passwordsBest regardsKornelia.
➡️ Reply
#Graseby/Goring-Kerr by Jose Luis Perez Contreras on 2011-11-25 19:34
Serian tan amables de venderme manual de usuario y o servicios del detector de metales Graseby/Goring-Kerr Tek DSP.Gracias por su atencion.Jose Luis Perez Contreras
➡️ Reply
#Graseby/Goring-Kerr by Cristobal Perez on 2011-04-01 00:00
In my factory, I have a metal detector Graseby/Goring-Kerr, wihich Ican not to calibrate, because I don\'t have the password.I don\'t have the manual.Please, send the manual and the password to my email.Regards
➡️ Reply
#Graseby/Goring-Kerr by John Beddard on 2011-06-21 13:58
Can you supply a contact number in the uk so that we can get one of your technical people to look at our machineType 2022Serial number 56798-3Best regardsJohn Beddard
➡️ Reply
#Graseby/Goring-Kerr by Jozef Granops on 2011-03-04 11:51
Iam looking for the representative in Poland of the Graseby /Goring Kerr metaldetector Type TEK 21
➡️ Reply
#Graseby/Goring-Kerr by Jim on 2011-04-19 20:33
Graseby G K no longer exists. The company that purchased them is Thermo Fisher Scientific. May be you could try that name in Poland. Good luck.
➡️ Reply
#Graseby/Goring-Kerr by Todd Flood on 2008-11-20 05:53
We need TEK DSP MODEL OPERATING MANUEL OF GORING KERR METAL DEDECTOR
➡️ Reply

Contact Us

🚑Shop Location🛠️

Industrial Electronic Repair
124 Five Forks Dr PMB #208
King, NC 27021
🚑 Rush repair shipments only — no walk-ins.

📞Phone

1-336-969-0110

📦Mailing Address🚛

Industrial Electronic Repair
124 Five Forks Dr PMB #208
King, NC 27021
📦 Mailing Address (for invoices or shipped repairs)
No walk-ins accepted.