Ird Mechanalysis for Service call 1-336-969-0110 at Industrial Electronics Repair

Ird Mechanalysis Service & Repair Forum

Dear Sirs,I have bought an used Fast Track analyser from an ebay seller.I am looking for a on operating software for this device, more specifically, the memory of the analyser had been reseted before and i look for the programms that can be played into the analyser that are: data collection, balancing, and the software package COASTDN for the start runs.Please inform me if you could send us files that we can than played onto the device (we have the software that can do it). Please make us an offerBest Regards.W. Makaruk

— Posted by W. Makaruk on 2008-09-25

Reply🗨️Ask a New Question Below❓

If you need your Ird Mechanalysis unit tested or repaired,
give us a call at 1-336-969-0110.
We offer fair estimates and extended warranties on the work performed.
Shipping/Receiving:
Industrial Electronic Repair
145 Rockwell Place Ct
Tobaccoville, NC 27050
Phone: 1-336-969-0110

Recent 26 Comments

#Ird Mechanalysis by Visalia Electric Motor Shoop on 2005-08-31 23:17

We have a model# 345 IRD Mechanalysis Balancer and we need to have it repaired. Do you repair these machines.Please let me know.Lisa Woodhouse

#Ird Mechanalysis by Craig Jackson on 2007-01-08 15:04

I need an operating manual for an IRD Mechanalysis Model 345. Can I get one scanned and emailed as a PDF file?

#Ird Mechanalysis by Roberto Perez on 2007-05-21 15:18

Hi: I am looking for a company that: First , I can send my IRD DATA LINe to be repair.Second: I need a new set of cables for IRd Fast trackThird: I need a chip for IRD Fast track DC_DC_ converter (dip371515db)part # IRD 35109.Do you service this equipmnet (data line) and do you sell chip and cables?...
Show More

#Ird Mechanalysis by Locklear on 2007-07-16 14:47

Looking for a Prom Board ASM IRD Part # 24144 fro the above Monitor

#Ird Mechanalysis by ANAS on 2008-01-31 08:05

DEAR I NEED A MANUAL BOOK OG IRD MECHANALYSIS WITH MODEL 880. BECAUSE I HAVE A IRD MECHANALYSIS BUT NO MANUAL BOOK. I NEED THE LESSON ABOUT THE BASIC OF VIBRATION MODULE 1 AND MODULE 2. I NEED IT FOR LEARNING ABOUT VIBRASTION..THANKYOU

#Ird Mechanalysis by JAYARAJAN.C.N on 2008-06-08 08:30

Hello, We are using the above model for three 130MW units in Moolamattom. Now we are suspecting some problems in some channels. We hope you will send your offer via my email.Regards,Jayarajan.C.N,Exceucutive Engineer,Generation Circle,KeralaState Electricity Board,Moolamattom -685589,Kerala, India.

#Ird Mechanalysis by Anas effendi on 2008-06-13 03:09

NEED A MANUAL BOOK OG IRD MECHANALYSIS WITH MODEL 880. BECAUSE I HAVE A IRD MECHANALYSIS BUT NO MANUAL BOOK. I NEED THE LESSON ABOUT THE BASIC OF VIBRATION MODULE 1 AND MODULE 2. I NEED IT FOR LEARNING ABOUT VIBRATION..THANKYOU

#Ird Mechanalysis by ISAAC SINYANGWE on 2008-07-12 06:49

We are currently using Model 290 IRD (c) 1998 Mechanalysis Balancer and we are in a position of not knowing what to do with the machine whether to have it repaired or only calibration is required.This is what we are experiencing:-the machine is not responding to the weights initially indicated as re...
Show More

#Ird Mechanalysis by W. Makaruk on 2008-09-25 19:27

Dear Sirs,I have bought an used Fast Track analyser from an ebay seller.I am looking for a on operating software for this device, more specifically, the memory of the analyser had been reseted before and i look for the programms that can be played into the analyser that are: data collection, balanci...
Show More

#Ird Mechanalysis by Benjamin Villegas on 2008-12-09 17:56

Hi, i have the files to load the os to the fast track, any version and the balancing and cost down program. my mail is cbdservicio@hotmail.com contact to me.

#Ird Mechanalysis by ertac hurdogan on 2009-01-15 08:22

DEARI NEED A MANUAL BOOK Of IRD MECHANALYSIS WITH MODEL 246. BECAUSE I HAVE A IRD MECHANALYSIS BUT NO MANUAL BOOK. THANKYOU

#Ird Mechanalysis by paul J. Guay on 2009-02-03 12:39

Units digitol output stuck on 00 does not scan

#Ird Mechanalysis by miguel bustillos calvo on 2009-04-14 21:34

recently acquire an ird balancing system model fast track, machine/instrument serial # 9311552, it was provide with your respective computer software.it was installed in my computer but when it runs appears the next messageird mechanalysis data analysis sistemwelcome to the ird7090 v.2.03oct 1989nor...
Show More

#Ird Mechanalysis by cristian ghita on 2009-06-24 13:44

. Data processing (diagnosis) with Amethist 1.01 program- data were taken over from the data collector 890 IRD Mechanalysis(England). Operating the data collector 890, model7090 PMP software, according to ISO 2372.

#Ird Mechanalysis by NARONG SIRIWATTANAWONG-SAKUL on 2009-11-15 05:27

We have this part for IRD FAST TRACK

#Ird Mechanalysis by rick gatchell on 2009-11-16 15:58

looking for spares for this unit or direct replacements

#Ird Mechanalysis by Dennis Dixon on 2010-07-28 17:08

Please advise if you can supply [2] only rebuilt or repaired IRD model 5806 vibration monitorAwaiting your reply Thanks, Dennis

#Ird Mechanalysis by Carlos Dominguez on 2010-12-01 21:46

1. How do I adjust the contrast on the Fast Track screen.2. We have Emonitor Odyssey. I could load the Fast Track Operating System, but how do I load the balancing program and the Startup-Coastdown programs.

#Ird Mechanalysis by Saul Bonilla on 2011-01-17 16:26

HelloWe are using the Model 5806 and only work a channel ( channel one)We Hope your offer .RegardsSaul BonillaEnee, HondurasPhone 26605706

#Ird Mechanalysis by John Richards on 2011-03-06 17:47

I have a vizio tv with a broken cable conecting the screen to the video buffer board, this cable has a chip on it .the chip is good . can you repair it?

#Ird Mechanalysis by Jose Sanchez on 2011-08-11 23:01

necesito por favor el manual de usuario de este modelo ird 880 mechanalysis, en español

#Ird Mechanalysis by saul bonilla on 2011-10-14 14:59

helloI have a ird 5806 it need repair.you can it ?

#Ird Mechanalysis by mohit bansal on 2011-11-02 07:12

SIR WE ARE USING IRD MECHANALYSIS 880 MODEL HERE IN NTPC AURAIYA. BUT NOWDAYS IT IS GIVING PROBLEM WHILE CHARGING. SO PLEASE PROVIDE ME REPAIR MANUAL SO THAT WE CAN REPAIR OUR EQUIPMENT

#Ird Mechanalysis by Saul Bonilla on 2011-12-19 22:17

HolaNecesito la reparacion de un monitor model 5806 de IRD MECHANALYSIS, no aparece nda en displey , no funciona nada.Ing. Saul BonillaENEE, Honduras.

#Ird Mechanalysis by Carlos Eduardo Franco on 2012-05-15 16:43

Dear sirs:Please send me information and operation manual of IRD 345 mechanalisys.Very truly yours,carlos Eduardo Franco G.MECHANICAL ENGINEER

#Ird Mechanalysis by James M Gradick on 2025-02-26 22:11

I need Cleaning/Calibration/Certification (ISO NIST) Tracible, for my IRD Fast Track Data Collectors. OS Download and Balancing/Coast Down program. Is that something you do?

Contact Us

🚑Shop Location🛠️

Industrial Electronic Repair
145 Rockwell Place Ct
Tobaccoville, NC 27050
🚑 Rush repair shipments only — no walk-ins.

📞Phone

📦Mailing Address🚛

Industrial Electronic Repair
931-E S. Main St #204
Kernersville, NC 27284
📦 Mailing Address (for invoices or shipped repairs)
No walk-ins accepted.