Leland Faraday for Service call 1-336-969-0110 at Industrial Electronics Repair

Leland Faraday Service & Repair Forum

Model M-295E single phase motor. Is it possible to reverse the motor direction and if so, which wires would I change.Motor used in heating system, and running backwards, it\'s trying to force water back to radiators, instead of to the boiler.

— Posted by Ben Jarnutowski on 2009-01-16

Reply🗨️Ask a New Question Below❓

If you need your Leland Faraday unit tested or repaired,
give us a call at 1-336-969-0110.
We offer fair estimates and extended warranties on the work performed.
Shipping/Receiving:
Industrial Electronic Repair
145 Rockwell Place Ct
Tobaccoville, NC 27050
Phone: 1-336-969-0110

Recent 52 Comments

#Leland Faraday by Richard Harbert on 2006-01-27 23:59

We have a brand new (never used) 15 year old vacuum pump with a Leland Faraday motor attached to it. We need to wire it for 208/220 volts but the wiring instructions are missing. The id tag on the motor says it is Type: ASFA BB and Model: LFI 84015C. The wires all have their id tags, we just need to...
Show More

#Leland Faraday by Betty Cleveland on 2006-07-19 18:12

Need a wiring diagram for a compressor.Thank you for your help.

#Leland Faraday by AbraahamLcn on 2007-01-08 17:06

Give me link to SEO software (promotion, advertisement, etc.). I\'m need it to promote my new e-shop. Thanks.

#Leland Faraday by Julien Lepitre on 2007-06-02 20:59

I have a 1.5 HP motor, it has 4 wires, one black, one red, and two that appear to be brown? They may of been a different color before? I had to wipe grease off of them just too see the red, and black wires. Other info I have is a Type # R 59, 110/220 volts, No.3639L3580, CV 3071, FR 203/4, 1725RPM, ...
Show More

#Leland Faraday by Dennis Reiman on 2007-06-22 01:33

I need a wiring diagram for a Leyland Faraday Model M431, 3hp, 230v motor. Mfg#PB184C17FB2D. Another # not labeled is#LR-33543. I think the motor is currently wired wrong and the wire box plate is not original. Any help would be appreciated.

#Leland Faraday by Glenn Trapp on 2007-09-16 09:04

I require a wiring diagram for a KEW 1640HA High pressure cleaner, unit is complete but the hot water/steam side will not work. Any help with a schematic will be greatly appreciated.thanks, Glenn.

#Leland Faraday by Darryl Hendricks on 2008-01-12 01:27

I need the wiring diagram for a leland faraday motor for my air compressor the modell # xm005 thank you Darryl Hendricks

#Leland Faraday by Edward J. Parent on 2008-03-14 14:36

wiring diagram for 110 volts

#Leland Faraday by Bob Washburne on 2008-04-23 12:37

Hello. I recently purchased a used 60-gallon air compressor which appears to be about 50-years old. It is driven by a L-F motor. It was wired for 220V operation. There is no diagram to convert it to 115V. The wires have small, narrow colored strips of tape around them which appear to be from the fac...
Show More

#Leland Faraday by Charles mills on 2008-05-28 15:05

I need the wiring diagram for the motor. It\'s a M306

#Leland Faraday by al mccullough on 2008-06-03 01:00

please send diagram

#Leland Faraday by Todd Geis on 2008-09-22 18:39

I have a Leland Faraday motor that I can not get referenced. Can you help?Stock # M-680EHP: 1.5RPM: 1725Volts: 208, 230/ 460Phase: 3Insul: class BFrame: LA56Hduty: Cont.Type: SCModel #: 8-182446-01

#Leland Faraday by Bill Henry on 2008-09-28 13:35

Where can I find parts and a manual for a KEW 1840HA machine. Thanks Bill

#Leland Faraday by terry on 2008-11-08 21:06

i have a lelan faraday motor model # m-546da . i would like to know if that motor is reverisable or not. i would like a wireing diagram for that model . thank you

#Leland Faraday by Anil Singh on 2008-12-14 08:49

I require a wiring diagram/Manual for a KEW 1640HA, KEW 3040H High pressure cleaner, Any help with a schematic will be greatly appreciated.thanks, Glenn.

#Leland Faraday by Ben Jarnutowski on 2009-01-16 18:09

Model M-295E single phase motor. Is it possible to reverse the motor direction and if so, which wires would I change.Motor used in heating system, and running backwards, it\'s trying to force water back to radiators, instead of to the boiler.

#Leland Faraday by alan dapp on 2009-03-16 19:10

Please help I need the wiring diagram for a Leland Faraday electric motor, 3hp 1740 hp stock # xm003b date code dy Sincerely, Alan dapp

#Leland Faraday by Muhammed Salim on 2009-06-10 20:44

Dear Sir,We would like you to provide us with relevant information and valid quotation for the following requirements,MACHINE TYP CLEANING MACHI NE TYPE CLEANING ELECTRICAL RATING 380/460VAC 8KW 60HZ FFT COLD WATER; 20-170 BAR; CAPACITY 500-1290 L/H; MAXIMUM TEMPARATURE 65 DEG C; “NEW MODEL IS 100% ...
Show More

#Leland Faraday by H.R. Heggedal on 2009-06-23 00:10

i have a leland faraday 5hp electric motor it is 3 phase. model #smd0367. i need a wiring diagram

#Leland Faraday by Robert Krakowiak on 2009-07-23 09:11

I,m looking for circuit diagram of KEW high pressure cleaner 3040HA. Would You like to help me to resolve this problem

#Leland Faraday by greg baer on 2009-09-22 20:19

we have a 5 hp, 1740 rpm, 24.5, single phase stock # sm-005b motor to drive a compressor. we manufacture solar heating panels and finally the business is starting to pick up where we can justify using this compressor. the wiring schematic is gone. can you either help with the wiring schematic or dir...
Show More

#Leland Faraday by Mike Jarrett on 2010-08-06 18:49

Have a MN-M-2052A motor. What color/number wire controls the cintrifical switch

#Leland Faraday by Glenn Fodor on 2010-08-27 15:56

Does anyone have a wiring diagram for a 3hp, 230 volt, 1750 rpm, M431 motor?

#Leland Faraday by eldon evans on 2010-10-16 18:12

i need a wiring diagram for a wood splitter - leland farady- 3/4 horse motor M271 -from 220 to 110

#Leland Faraday by Ronald Rocap on 2010-11-06 23:17

I have had this lathe for some time and have retired, I have free time and would like my lathe tobe able to reverse. I found the tag but no wiring diagram. I am trying to get this wired but I need a little help. I have a square D drum switchand think i have that figured out but I\'m not sure which w...
Show More

#Leland Faraday by Ron Rocap on 2010-11-11 04:35

1. Red wire from capacitor. 2. Blue from motor to sw. 3. White and Green were hooked together at motor. 4. Yellow and Black were connected together at motor To reverse you changed the Red and Black The motor is wired as 220V 1 Phase. I had no wiring for the motor but I did have the Plate The switch ...
Show More

#Leland Faraday by luis miguel rios diego on 2010-11-16 10:10

Hi I have a machine kew good 3040ha and I can not connect the power contactor, I see the winding water pump is burned and I would like to know how to put the said coil. We appreciate you send me the installation diagram of the coil. I would be very grateful and thank you very much.

#Leland Faraday by Ron Rocap on 2010-12-28 22:52

Thanks anyhow guys I figured it out, Just sat down with my dog (he wasn\'t much help but company) got the motor reversing and running foward without any mishaps.Didn\'t need any repair just info. they didn\'t seem to want to share any info. I\'m sure the motor came with some instructions for an elec...
Show More

#Leland Faraday by stan mooneyham on 2011-02-04 22:46

I have a customer looking for a LELAND FARADAY motor. These are the only specs that I have on it.5HP1800RPM1 PHASE230 VOLTF213T FRAMEEXPLOSION PROOFThank you, Stan.

#Leland Faraday by Bob Siever on 2011-06-27 21:09

model# 365003stk#XM-015Edate KDRPM 1745Amp 15/7.8-7.5Hertz 60 Single phase I really need a wiring diagram. This motor can run 120V or 230V. A diagram for both would be GREAT!!Thank You!!!!!

#Leland Faraday by JOE on 2011-09-12 17:39

LELAND-FARA DAY STOCK NO.XM005BHP-5 RPM-1740VOLT-230F.L AMP 24.5

#Leland Faraday by Gordon Cammock on 2011-10-15 05:36

Fault Codes showing P1, can you help?

#Leland Faraday by didier on 2011-10-28 18:37

new watertank

#Leland Faraday by mike allermann on 2012-03-22 03:27

i have a 3 hp single phase 6 wire leland electric motor and do not know how to wire it

#Leland Faraday by jason on 2012-05-16 16:41

Leedid you get the problem sorted I have same fault in my unitany help I would be gratefulcheersJason

#Leland Faraday by rafal on 2012-05-28 09:20

pdf I need to servicing the 3040HA kew pressure washer quickly!

#Leland Faraday by Ken on 2012-06-21 15:45

I have Leland Faraday 3/4 HP V2550 model G56 1578 02. The wiring diagram is damaged on the motor plate. I am trying to hock up a reversing switch.. Thank you for any help. Ken

#Leland Faraday by nh soon on 2012-06-22 00:07

hi,i mr ng from malaysia.i have dynagen g26-2001 inverter but the use manual is lost,can you e-mail to me.TH

#Leland Faraday by gary joslin on 2012-06-28 02:55

part# m30502 frame s182t volts 115/230 the wiring diagram is not complete it has two capasatores and 8 wires

#Leland Faraday by Mary Ann Mathis on 2012-07-02 14:39

Good MorningCan you please forward a wiring diagram for a M-511U 1/3HP 3450 RPMCat# C48H2N109B1

#Leland Faraday by matt shea on 2012-09-11 20:42

i have a 1 hp 1 ph leland faraday compressor motor with no wiring diagram. i want to know if i can run it on 110. the number on the side plate is 51 j17 6131 1 m306 81c frame k203. the wires coming out of the motor are red green yellow white blue and black.i need to know how to wire it for the right...
Show More

#Leland Faraday by Jeanette Ashhurst on 2012-11-12 23:55

I am after Fuel level sensor #6420303 and Temp probe #1119270. Could you give me an idea on price and how much delivery to Australia would be.ThanksJeanette

#Leland Faraday by work\'s water works on 2013-01-10 01:27

I have a Logan leathe in my shop M 1920 need to wire it for 220 volts need wiring diagram. thank you John Work

#Leland Faraday by Terri / Western Electric Motors on 2013-04-11 21:15

Hello we have the following Leland Faraday Motor in our shop. I need to see if you have a wiring diagram for this motor. Below is all of the data from the plate.2HP, 3450 RPM, 56 Frame, 115/230 Volt, 21.2/10.6 Amps, 1 phase.#6145, 3 P19 8050 1, M2904.7 leads:WhiteRedGreenYellowRed/BlackBlackBrown.Th...
Show More

#Leland Faraday by rye on 2013-11-26 01:20

Hi Terri I have the wiring diagram which you desire. to ease my assistance please let me know how your motor is terminated and if is not than what voltage you prefer.let me know

#Leland Faraday by Greg Pink on 2015-01-29 17:32

I have one of your motors model # 8-186701-01 and I\'m looking to purchase another one just like this one. can you tell me if this motor is still available or is there an equal to this. Also where in the Boston area can I purchase one? Thank you, Greg Pink

#Leland Faraday by Nicole Miller on 2015-08-24 13:55

I am wondering if you have a quote on or would have a picture electrical diagram for a Leland Faraday SCR Variable speed drive Model # MSCR.Please let me know as soon as possible Thanks Nicole

#Leland Faraday by William Douglas Smith on 2016-04-02 17:44

I am replacing my current, bad, 4HP, which is a 3 wire (black, white & green) with your 2HP M-2958E, which has 4 wires (red, black, yellow & blue).How can I wire this to my pressure switch which has four attach locations, 2 hot and two for the motor attach and a ground location.Thanks,Doug

#Leland Faraday by James Gray on 2019-11-22 18:19

Part# 230HP 1/3 Frame F56Type RKModel F-56-3550-02SN# AAMIVolts 115/230RPM 1725

#Leland Faraday by TOM CALGARO on 2021-08-10 20:15

I HAVE A 1980'S LELAND FARADAY WATER WELL PUMP 1RM2-S/A 4H7127119, SK 2ABN-175. THE PUMP IS LEAKING WHERE THE MOTOR SHAFT GOES INTO THE OTHER UNIT AND IT LOOKS LIKE IT'S THE BEARING. MY QUESTION IS, CAN THIS BEARING BE REPLACED AND IF SO WHERE CAN I PURCHASE THE CORRECT BEARING?

#Leland Faraday by Wesley young on 2022-05-26 00:53

Need to know how the wires are hooked up on the pump all of them inside the canopy

#Leland Faraday by Robert Cancellieri on 2024-08-11 20:41

I have a Leland Faraday 3 hp 230 volt single phase motor. It has 6 wires coming out of the motor, Black, Blue, Red, Green, White, Yellow. Code K, 61J5-8500-2, Stock M390, 84D, I wish to wire it to a single phase, 230 Volt, incoming power. Any help with this would be much appreciated. Thank you

Contact Us

🚑Shop Location🛠️

Industrial Electronic Repair
145 Rockwell Place Ct
Tobaccoville, NC 27050
🚑 Rush repair shipments only — no walk-ins.

📞Phone

📦Mailing Address🚛

Industrial Electronic Repair
931-E S. Main St #204
Kernersville, NC 27284
📦 Mailing Address (for invoices or shipped repairs)
No walk-ins accepted.