Leroi Dresser Service & Repair Forum

voir partie compression

— Posted by ahmida on 2010-02-15

Reply🗨️Ask a New Question Below❓


Recent Comments Search: "Leroi Dresser"

If you need your Leroi Dresser unit tested or repaired,
give us a call at 1-336-969-0110.
We offer free estimates and extended warranties on the work performed.
Shipping/Receiving:
Industrial Electronic Repair
145 Rockwell Place Ct
Tobaccoville, NC 27050
Phone: 1-336-969-0110

Recent 178 Comments

#Leroi Dresser by Mark Milam on 2013-03-04 15:00
Model 1a 219-132-6 What is the CFM of this 100 HP compressor?
➡️ Reply
#Leroi Dresser by joe kelley on 2008-07-06 02:25
I recently purchased a 1978 Ford 7000 equpped with a road striping unit. It has a Leroi Dresser Compressor. It also has a hydraulic system driven by a Perkins diesel engine that drives both the hydraulics and the compressor. It starts up with no problem and will pump air up to 160 lbs, psi and then …...
Show More
➡️ Reply
#Leroi Dresser by matt on 2011-11-17 01:40
looking for the manual or specs on this unit myselfpls thxmatthewmhyde_16@hotmail.com
➡️ Reply
#Leroi Dresser by kit rosling on 2008-11-24 05:29
I have purchased a leroi, dresser compressor recently but the engine has not run for quite some time (5 yrs ?) and is obvious that it has had water in the heads and visible rust stains outside the block. Where can i find a comparable engine to replace this? It looks like this engine is a allis chalm…...
Show More
➡️ Reply
#Leroi Dresser by Jim Ferrell on 2010-01-18 13:07
Our compressor is needing service. The coupling between the engine and the compressor has failed.Please recommend the nearest service center.Thank you,JIM
➡️ Reply
#Leroi Dresser by Paul Woodworth on 2010-11-13 21:08
Hello sir: I am trying to wire up a 10 hp Leroi comperessor model 660A. I need a wireing deogram for the 3ph pressure unloader switch. Do you wire it to the pressure switch? Drop me a line monday if you can. Also is there a parts book on the compressor . Paul
➡️ Reply
#Leroi Dresser by Orlando Farnetti on 2010-11-16 12:38
I\'m looking for air compressor Dresser 440A.we need to buy new six.wuold you help pleaseBest regardsOrlando Farnetti
➡️ Reply
#Leroi Dresser by george on 2012-09-17 17:49
would like to know were to get vavles for the head cyl thanks george609 567-2295
➡️ Reply
#Leroi Dresser by Weissiope on 2009-11-15 12:18
I need a elliptical trainer or any other good excercise machine, to use at home. are there any websites where i can purchase this item? so i can train at home. as this is the excellent product to take as it train all the body.
➡️ Reply
#Leroi Dresser by steve on 2010-07-28 20:14
I am looking for the Model 20-25-30SS II Installation-Operation, Maintenance and Service Manual
➡️ Reply
#Leroi Dresser by MERLE HOOVER on 2008-04-02 13:07
drifter air control valve or substitute part for a leroi/dresser drill Model CDR-12E part number is AM81-247. Controls rotation/feed/drill and blow.
➡️ Reply
#Leroi Dresser by steve on 2012-06-16 23:15
hi thear steve at bigkidtoys.com looking to get parts fore a 550 leroy cmpresser need in and out valvs and all gsk.s and such 707-294-0133
➡️ Reply
#Leroi Dresser by Thomas Belesky on 2010-11-05 21:08
I am looking for the specifications of what appears to be a LeROI Dresser Rotary Screw Pump. The housing has the following stampings:Mfg: A219-84-3Serial No: 4154X110The best information I have been able to find is the original vendor was Gardner Denver but teh actual Rotary Screw Pump OEM is LeRoi …...
Show More
➡️ Reply
#Leroi Dresser by BOBBY RAY on 2008-04-03 19:15
I NEED HELP FINDING MANUALS FOR MODEL 130RGITHANKSBOBBY RAYBAXTER HEALTHCARECLEVELAND MS 38732
➡️ Reply
#Leroi Dresser by Rich on 2011-06-13 16:28
anyone know where I can get a parts book for this..
➡️ Reply
#Leroi Dresser by Dennis Hoffman on 2010-09-04 23:22
hi i have a leroi dressor compressor modelq160de ser3033x340 rotary vane compressor needs about 150.00 worth of parts and they are available but would like to sell this unit asking 1000.00 for it the johndeere engine runs great you can call me at 754-456-1906
➡️ Reply
#Leroi Dresser by Lee Burnett on 2010-12-01 14:16
Need upper end rebuild parts Series 800 LeRoi/Dresser air compressor Serial # 458X5251 20 H.P.
➡️ Reply
#Leroi Dresser by Tim Wolfe on 2011-01-14 22:28
Need a manual for this compressor and need to know what size motor should be on it. Thanks
➡️ Reply
#Leroi Dresser by Mark A Bellora sr on 2008-11-20 15:37
I am trying to find a starter for my compressor LeROI 175 Rotary Screw Portable Air Compressor 1973 or 1974Compressor Model---- 175SG1-USN ----------------------291X277International EngineEngin Model------------UC 200-L- LO 24AEngine SN -------------34871Can you help me find the correct part or a pa…...
Show More
➡️ Reply
#Leroi Dresser by Dustin Engle on 2010-12-16 20:51
I have a Le roi Dresser 440 compressor and want to get running.Ihave rebuilt the unit but it was already tore down when I acquired it.I am willing to pay for manuals, please let me know if you can help.
➡️ Reply
#Leroi Dresser by Brett Nelson on 2010-10-17 19:23
have a model 75 RGI and have the 4 cyl fordwater in the oil now and it smokes been tryin to get it put back to working order for just blowing out sprinkling systems seems to be a money pit no one knows or has heard anything about this model please help.
➡️ Reply
#Leroi Dresser by paget jarvis on 2012-09-06 15:56
I Have been using Leroi Compressor for the past 20 years i recently boughta newer model it will not hold the air in the tank with the valves shut off i think i know where the air is escaping from but i do not know the name of that particular part and i don\'t have a manual for the 660A.thanks,
➡️ Reply
#Leroi Dresser by Anthony Counts on 2008-04-08 11:43
I have been given a Dresser Series 5000, S/N 4005X22583 compressor (less motor and tank). I am building a compressor unit for running a small sandblaster, but I need to know specifications on the unit above and what HP and RPM motor, as well as the size of the motor pulley (double pulley) I need to …...
Show More
➡️ Reply
#Leroi Dresser by Mike Frank on 2012-12-17 20:13
I am attempting to secure an Installation, Operations and Maintenance (IOM) manual for LeROI 3274X30 (S/N 1A219-89) Air Compressors. I am developing maintenance procedures.
➡️ Reply
#Leroi Dresser by Matt on 2009-08-17 22:21
Hi, I am looking for a manual for a leroi dresser model Q160G, any help would be appreciated.ThanksMatt
➡️ Reply
#Leroi Dresser by Tom Parker on 2012-12-26 21:25
I have a 175D Portable compressor. Engine will not accelerate when there is a demand for air. Need help with troubleshooting and parts.Thanks Tom
➡️ Reply
#Leroi Dresser by Ken on 2019-02-26 17:59
Need a insert bearing h21-978
➡️ Reply
#Leroi Dresser by Phil Brown on 2011-11-19 04:51
I have the serial and model number for this pull behind air compressor. If you could find out when it was built and were I could find a owner\'s manual and repair manual that would be great.Serial #2057X22Model #0100RGW
➡️ Reply
#Leroi Dresser by Henning Small on 2009-02-05 08:13
HI I am looking for service kits for the above machines and cant find some one here to assist, Can u please help.Regards
➡️ Reply
#Leroi Dresser by luis f paredes on 2011-05-05 18:31
i am looking for the wiring diagram for my DOERR LR-13758 2hp motor model 90450-D XD. i need to convert it to 3 phase if you can please help ....... Thank You Luis Paredes cell (626) 373-6890
➡️ Reply
#Leroi Dresser by NESTOR VERGANI on 2009-06-30 22:51
WE NEED AS SOOM AS POSIBILITY THE FOLOWIN PARTS.FOR THE UNIT LERIO 1600 , MODEL A219-148-3, SERIAL 3165X95COUPLING (1 )BEARING 7313 BE.GAP (2)BEARING 7214 BUO ( 3 )GEAR P.O.P. 036.45.0 (1)GEAR P-O-P- 036.45.1 P/N 26944-2 (1)
➡️ Reply
#Leroi Dresser by reza on 2012-08-07 10:10
would you please answered below my question.1.)how con commissioning no-load test compressor type 4E3+BALANCE LINE CE-55985? 2.)during the fist start up when we REACH the speed more thane 37oorpm by turbine drive low speed gear vibration AND tried what is you recommended ? we check alignment everyth…...
Show More
➡️ Reply
#Leroi Dresser by CHRIS on 2009-12-02 12:58
i need the main barring . piston pin and bushing for the small piston in the pump. can you help me out?thanks chris847-778-2787
➡️ Reply
#Leroi Dresser by Dinesh Kannan on 2010-04-07 06:54
gents,i need to know where the above subjucted parts is availabe for the LE ROIin saudi arabia
➡️ Reply
#Leroi Dresser by Hannah on 2011-02-11 21:24
Please prvide pricing and availability on a gasket overhaul kit for aSeries 600 Serial Number:455X7411
➡️ Reply
#Leroi Dresser by Ben on 2011-08-23 03:22
Do you have a crankshaft for the Dresser 5000? I need one.. call or email me. I have the specs you need, I\'ll give them to you.
➡️ Reply
#Leroi Dresser by Al on 2008-09-14 22:51
2a116-407 Suction Valve assembly Leroi Model W40-50SS. This is the same Valve on W40
➡️ Reply
#Leroi Dresser by John Mitchell on 2011-05-13 15:58
Serial # 3138X226. The unit will not deliver any compressed air. When the valve is opened, it gives one little \"poof\" and nothing more. It seems to be making compressed air because when I shut the engine off, the compressor \"blows down\". It was working fine up until this problem. Can you tell me…...
Show More
➡️ Reply
#Leroi Dresser by john on 2011-06-13 11:08
Model 800 not 8000
➡️ Reply
#Leroi Dresser by James Geer on 2008-09-19 18:02
I have a dresser series 400 compresser (s)# 453x15390 five hp.it was made in Sidney Ohio.. What I need is aparts list and a co. to by parts from Thank you j geer
➡️ Reply
#Leroi Dresser by marc on 2010-09-05 07:07
Model 85rgewSerial 2022x156
➡️ Reply
#Leroi Dresser by Steve Kekedy on 2011-06-01 15:44
Compressor won\'t build up pressure beyond 60 psi, new regulator set at 110psi. Compressor has been slowly declining and won\'t shut off
➡️ Reply
#Leroi Dresser by Allister Davis on 2010-02-15 12:03
We have a customer with a Dresser compressor, model # 880A, ser# 4020x402. If this is your model please provide a parts breakdown & advise if you have a distributor in Canada.RegardsAllister
➡️ Reply
#Leroi Dresser by Ronald W. Riggan on 2008-11-20 19:29
I have a cylinder head that needs to be repaired. needs reed valves and a head gasket. Where do I need to send it for an estimate? I need to know ASAP. Thanks Ron.
➡️ Reply
#Leroi Dresser by Luis Fernando Santana on 2012-10-15 18:50
Good afternoon i need the manual for my compressor leroi CL30 CUB because i need to replace some parts.If you can sale the manual i appreciate that.Thanks.
➡️ Reply
#Leroi Dresser by DAVID WHITEMAN on 2010-05-05 17:10
I WAS WONDERING IF YOU MAY HAVE INFORMATION (SERVICE) FOR AN OLD WAYNE MODEL 6300-3H COMPRESSOR. ANY INFO WOULD BE APRECIATEDTHANKS
➡️ Reply
#Leroi Dresser by Brad Milmine on 2013-01-29 16:34
I have a 5 hp. electric Dresser compressor and the centrifugal unloader is not operating. Is there an adjustment for this system. Any help with this would be appreciated. Thanks Brad
➡️ Reply
#Leroi Dresser by GARRETT HUTCHISON on 2009-01-20 23:19
could i buy the manuals for a LEROI DRESSER 1500CFM 100PSI3054X27 NOT SURE ON THE YEAR THANKS
➡️ Reply
#Leroi Dresser by LV Sale on 2011-06-16 13:55
It is possible to tell, this exception :) Louis vuitton bags , Yes it is a fantasy In my opinion you are not right. I am assured. I can prove it. Write to me in PM, we will talk. I advise to you. You were mistaken, it is obvious.
➡️ Reply
#Leroi Dresser by Tim Wolfe on 2011-01-14 22:29
Need a manual for this compressor and need to know what size motor should be on it. Serial number 40052X4064 Thanks
➡️ Reply

Contact Us

🚑Shop Location🛠️

Industrial Electronic Repair
145 Rockwell Place Ct
Tobaccoville, NC 27050
🚑 Rush repair shipments only — no walk-ins.

📞Phone

1-336-969-0110

📦Mailing Address🚛

Industrial Electronic Repair
931-E S. Main St #204
Kernersville, NC 27284
📦 Mailing Address (for invoices or shipped repairs)
No walk-ins accepted.