Nuarc Service & Repair Forum

When I turn the camera on it comes on for just a second then turns off. It does not trip the breaker just turns itself off. I do not know where to start. Electricial, swtich or board problem. I teach at a Career Technical School and do not have much money to fix equipment so I need to fix it myself. Thanks for any suggestions.

—> Purchase or Repair: Ticket Image

— Posted by Anthony Mitchell on 2011-05-27

Reply🗨️Ask a New Question Below❓


Recent Comments Search: "Nuarc"

If you need your Nuarc unit tested or repaired,
give us a call at 1-336-969-0110.
We offer free estimates and extended warranties on the work performed.
Shipping/Receiving:
Industrial Electronic Repair
145 Rockwell Place Ct
Tobaccoville, NC 27050
Phone: 1-336-969-0110

Recent 8 Comments

#Nuarc by dennis on 2009-12-17 20:53
I am using a nuarc vv1418 camera with rapid access film, I always get a weak or dark image out in the corners. Longer times weaken the center of the image. wondering if the angle of the lights is wrong?

—> Purchase or Repair:
➡️ Reply
#Nuarc by Anthony Mitchell on 2011-05-27 15:33
When I turn the camera on it comes on for just a second then turns off. It does not trip the breaker just turns itself off. I do not know where to start. Electricial, swtich or board problem. I teach at a Career Technical School and do not have much money to fix equipment so I need to fix it myself.…Purchase or Repair: Ticket Image...
Show More
➡️ Reply
#Nuarc by Rick Gustafson on 2007-11-28 16:33
Nuarc Model # SST1418TR Serial # 94B68-38Looking for the solenoid to operate the camera shutter. Wondering if you sell this part?

—> Purchase or Repair:
➡️ Reply
#Nuarc by XAVIER GALLARDO on 2010-02-22 00:15
Hello: looking for a NuArc VV 1418 Itek LensThanks

—> Purchase or Repair:
➡️ Reply
#Nuarc by Jeffrey on 2017-11-03 19:46
lowered the bed to reduce and bed will not come back up any suggestionsThank youJeff

—> Purchase or Repair:
➡️ Reply
#Nuarc by Anthony Mitchell on 2011-08-12 12:48
I have a NuArc process camera, it is old but does a good job. When the power switch is turned on the camera comes on but after about 10 seconds turns off. I do not know where to start. What is your best guess of the problem and the estmated cost to fix it. I teach printing to high school kids so mon…Purchase or Repair: Ticket Image...
Show More
➡️ Reply
#Nuarc by Edward Rivera on 2009-03-01 22:42
I don\'t have a manual for it and i have rapid acess film for it. I also don\'t know where to set the lens for line and haft tone. Pleas help me out. Thank You.

—> Purchase or Repair:
➡️ Reply
#Nuarc by Aaron Bass or Eric Gant on 2015-05-26 19:19
We are a small art school with a broken NuArc unit (specs below). It seems to be a loose wire, as the bottom row of buttons (start, cancel E8, etc.) will not start. So, we are looking for a repair person in the area.Unit specs26-IKS-NTNT C00-005120609.5ThanksAaron Bass

—> Purchase or Repair:
➡️ Reply

Contact Us

🚑Shop Location🛠️

Industrial Electronic Repair
145 Rockwell Place Ct
Tobaccoville, NC 27050
🚑 Rush repair shipments only — no walk-ins.

📞Phone

1-336-969-0110

📦Mailing Address🚛

Industrial Electronic Repair
931-E S. Main St #204
Kernersville, NC 27284
📦 Mailing Address (for invoices or shipped repairs)
No walk-ins accepted.