Procond Elettronica Service & Repair Forum

The Procond Elettronica MC-70 124438 treadmill board is experiencing abnormal behavior in the warehouse.

—> Purchase or Repair: Ticket Image

— Posted by mark bunker on 2005-11-23

Reply🗨️Ask a New Question Below❓


Recent Comments Search: "Procond Elettronica"

If you need your Procond Elettronica unit tested or repaired,
give us a call at 1-336-969-0110.
Estimates are free with an approved repair. Declined or unrepairable units are subject to a $75 evaluation, handling, and standard return-shipping fee. Extended warranties may be available.
Shipping/Receiving:
Industrial Electronic Repair
124 Five Forks Dr PMB #208
King, NC 27021
Phone: 1-336-969-0110


Recent 569 Comments

#Procond Elettronica by brusselle on 2015-06-21 10:48
Hello, I need where to buy or repair a Procond elettronica 3560089039 module and the price.

—> Purchase or Repair:
#Procond Elettronica by Angelo on 2006-06-20 15:32
The Procond Elettronica MC-70 124438 treadmill board is malfunctioning, affecting the production line. Urgent repair service needed to resolve the issue

—> Purchase or Repair:
#Procond Elettronica by Xhuneyt on 2006-06-03 16:22
I have a problem with a motor controler for waching machines, and i wanted you to help me about this. It has not enough force to roll the clothes. I changewd the chip, but it is still not working properly. The code: 3 560 332 06

—> Purchase or Repair:
#Procond Elettronica by suparjo on 2012-03-20 11:32
My LUX washing machine was in problem. According to the technision the CPU is not working properly. He remove the CPU but he did not sure.The CPU written as below:GE Procond ElettronicaType P451510093 F:6473Type E.124303983SW Ver.W2C01551 24/giu./05My questions are:1. Can that unit be repair2. if it…Purchase or Repair: Ticket Image...
Show More
#Procond Elettronica by Deremer on 2007-09-29 00:09
The Procond Elettronica MC-70 124438 treadmill controller is displaying Error Code E3, which suggests a potential issue with the speed sensor. Resetting the system did not resolve the problem, and the treadmill is currently not operational. Please advise on next steps for troubleshooting and repair.…Purchase or Repair: Ticket Image...
Show More
#Procond Elettronica by Lucien Huble on 2015-03-08 11:13
I have a faulty control board for EWF 1620 The resistor R82 has burnt out. I wish to replace it but I do not know it\'s value. Please can you send me the value and a schematic please? Thank you for your help.

—> Purchase or Repair:
#Procond Elettronica by ALEMU on 2006-12-08 15:16
Just had a board failure on Procond Elettronica MC-70 124438 treadmill controller. Will investigate further once this round is done.

—> Purchase or Repair:
#Procond Elettronica by allermann on 2007-06-01 04:50
One of the Procond Elettronica MC-70 124438 treadmill controllers is displaying unusual behavior in the warehouse.

—> Purchase or Repair:
#Procond Elettronica by YONIER PINON on 2006-06-20 17:32
The Procond Elettronica MC-70 124438 treadmill controller is malfunctioning, causing a halt in production. Immediate repair service is urgently needed to resume operations.

—> Purchase or Repair:
#Procond Elettronica by Lind on 2005-12-30 14:51
The Procond Elettronica MC-70 control board on the treadmill line is malfunctioning, causing repeated shutdowns during operation. This issue is impacting productivity and needs urgent attention from the repair service to minimize downtime.

—> Purchase or Repair:
#Procond Elettronica by salvatore rassu on 2010-10-20 15:21
Hi,Got a zanussi jet system 1400 xc and i am looking for the electronic board 45151005112430381/5If you have this part ? How much with the shipping to the uk?Looking to speak to you.RegardsSalvatore

—> Purchase or Repair:
#Procond Elettronica by ennikl on 2013-08-12 11:35
The Procond Elettronica 356033305 47-90 circuit board is displaying Error Code E304 intermittently, preventing the equipment from powering up. Please advise on troubleshooting steps ASAP. Thank you.

—> Purchase or Repair:
Dear Sirs,please send your best offer for following items: GE INDUSTRIAL FILTERS: 1. TYPE RANGER 520-280 2 PC 520 V AC, 50-60Hz, 0345, 280A, 40 degrees C, 82480 high leakage current connect protective earth first 2. TYPE RANGER 520-450 1 PC 520 V Ac, 50-60Hz, 0150, 450A, 40 degrees C, 80447 high lea…Purchase or Repair: Ticket Image...
Show More
#Procond Elettronica by John McGeady on 2011-03-09 22:12
think we need a new transformer, which has procond eletrrronica written on itcan you assist ?

—> Purchase or Repair:
#Procond Elettronica by Reimert on 2007-09-30 14:53
HelloIm also would like to test this my module, i don\'t know if it\'s working well Is it possible to have a schematic or technical datasheet of this module *******Waht is the cost for repair? What is the cost for a new one?GE Procond ElettronicaType P. 451510051 Type E. 12430392/5SW Ver. W2C01250 2…Purchase or Repair: Ticket Image...
Show More
Hi,COULD YOU TELL ME THE PRICE FOR A NEW PART FOR A PROCOND ELETTRONICA PART NO 356071101 - LABEL NO 452650111 - FOR Ariston dishwasher LSI 66 A. AND ALSO THE PRICE FOR A TRANSPORTATION TO ITALY.With regards, GIANFRANCO MANUNTA, via M. Macchi 87 - 20124 Milano - ItalyTHANK YOU

—> Purchase or Repair:
#Procond Elettronica by Nickolay on 2013-06-27 06:21
Good day.Have you the power board for delonghi coffee machine cod DeLonghi 5232109600, cod Procond Elletronica 3560033089?How much cost and can you send this part for me?

—> Purchase or Repair:
#Procond Elettronica by hodovanic on 2020-08-10 15:32
Board failure on Procond Elettronica NTTL1407, need immediate replacement. Initiating troubleshooting steps, will update with a progress report soon.

—> Purchase or Repair:
#Procond Elettronica by ALAMGIR on 2007-09-19 17:55
The Procond Elettronica MC-70 124438 treadmill board is malfunctioning, impacting our production line. Urgent repair service required to ensure operations can resume

—> Purchase or Repair:
#Procond Elettronica by hamed on 2009-06-17 10:29
Dear Sir, Mam,I have a treadmill icon health & fitness and it is damaged so I open the cover and see the board with this model MC-70 Aw.revPart #124438 damaged .I have a qouestion:Two parts of this board are damaged and I cant read the part number on them.so please let me know the parts number(dz1 a…Purchase or Repair: Ticket Image...
Show More
#Procond Elettronica by Lester Duplessis on 2007-06-01 01:50
Treadmill controller Procond Elettronica MC-70 124438 displaying Error Code E5 - Motor Overcurrent Protection triggered.

—> Purchase or Repair:
#Procond Elettronica by SETIABUDI on 2009-11-24 17:53
I would like to request a schematic or technical datasheet of Ref =Type Procon :451511360Type E.Z: 13200353/2SW ver USA0020515/00 T70THANKS A LOTBEST REGARDS

—> Purchase or Repair:
#Procond Elettronica by Steve Martel on 2007-10-26 10:40
We experienced downtime due to an issue with the Procond Elettronica MC-70 124438 treadmill controller. Urgently need to investigate the problem to prevent further delays. Any insights would be greatly appreciated. Thank you.

—> Purchase or Repair:
#Procond Elettronica by Independentmgc on 2022-03-12 06:19
or their samples written

—> Purchase or Repair:
#Procond Elettronica by Eric Tibbits on 2008-01-05 21:41
I have been having problems adjusting the maximum speed potentiometer for my treadmill. I am not an electrical guy. Could you send me a drawing showing the location of this part so I can fix my treadmill. Thanks

—> Purchase or Repair:
#Procond Elettronica by Telecasterduv on 2021-11-30 03:37
reproduced by hand, in contrast

—> Purchase or Repair:
#Procond Elettronica by Garminzwfm on 2022-02-23 00:26
ancient and medieval Latin,

—> Purchase or Repair:
#Procond Elettronica by Kiriakidis on 2006-11-09 00:57
The treadmill controller Procond Elettronica MC-70 124438 is malfunctioning, causing a production line issue. Immediate repair service is required to resume operations

—> Purchase or Repair:
#Procond Elettronica by schepers didier on 2011-08-24 12:31
My module for aeg lavamat 72800 /ge procond type p 451515351-e 132219810,version W1a 30106 19 apr 04.give me please the price to repair or to exchange my module ,en how to proceed.thanks

—> Purchase or Repair:
#Procond Elettronica by Vladimir Ayala on 2007-10-21 07:14
Looking for someone to repair a Procond Elettronica MC-70 124438 treadmill controller. Not working, need fixing asap.

—> Purchase or Repair:
#Procond Elettronica by reza ramezani on 2013-03-30 07:57
The Procond Elettronica 356033305 47-90 circuit board is not working.

—> Purchase or Repair:
part supply number: EN 132400

—> Purchase or Repair:
#Procond Elettronica by Rajen on 2007-10-21 05:14
Please provide me with more information about the Procond Elettronica MC-70 124438 treadmill controller. We are looking to determine if it is still supported or if replacement parts are available. Thank you.

—> Purchase or Repair:
#Procond Elettronica by freddy on 2009-01-30 03:11
Tengo un treadmill Image 10.6Q, aparece en la pantalla E2. y no funciona mi treadmill. que debo hacer. por favor ayudenme. gracias

—> Purchase or Repair:
#Procond Elettronica by Phill Goldsmith on 2006-06-03 18:22
The treadmill board on the Procond Elettronica MC-70 124438 is malfunctioning, disrupting the production line. Urgent repair service is needed to restore operations

—> Purchase or Repair:
The Procond Elettronica MC-70 124438 treadmill controller is malfunctioning, causing a major disruption in the production line. Urgent repair service is required to rectify the issue and resume operations

—> Purchase or Repair:
#Procond Elettronica by Nestor Juguera on 2008-05-26 23:32
need schematics for the 356069403 for even microwave delonghy mw605/3. Where can I get a copy?

—> Purchase or Repair:
#Procond Elettronica by Marco Gualengi on 2007-07-19 20:25
Hello, I am interested in purchasing a Procond Elettronica MC-70 124438 treadmill controller. Could you please provide information on pricing and availability? I am trying to source one quickly. Thank you.

—> Purchase or Repair:
#Procond Elettronica by Joseph on 2007-02-03 22:39
Can you please advise what it would cost to repair a MC-70 board for my Nordic Track treadmill? The power supply board has all the LED\'s lit (the PWM flashes only when it calls for speed). The motor works (I\'ve used a 12 vdc power supply to test). I\'ve also checked to make sure that 120Vac is sup…Purchase or Repair: Ticket Image...
Show More
#Procond Elettronica by Roger on 2007-09-19 18:55
The Procond Elettronica MC-70 124438 treadmill controller is displaying error code E2, indicating a possible issue with the speed sensor. Treadmill is not responding to speed adjustments and stops abruptly. Assistance needed to diagnose and rectify the problem

—> Purchase or Repair:
#Procond Elettronica by Esparza on 2007-04-05 00:56
I am following up on my previous message regarding the Procond Elettronica MC-70 124438 treadmill controller. The unit is still not functioning. Please provide assistance

—> Purchase or Repair:
#Procond Elettronica by ERMETO on 2007-05-14 22:19
The Procond Elettronica MC-70 124438, which serves as the treadmill controller, experienced a malfunction earlier today, causing unexpected downtime from 230 PM to 445 PM. I'm seeking a brief explanation before the next shift comes in. Thank you.

—> Purchase or Repair:
#Procond Elettronica by amin moradi on 2017-06-01 23:41
HI Please attach any schematics, hook-up diagrams, or manuals you may have.

—> Purchase or Repair:
#Procond Elettronica by Harbert on 2006-09-21 17:00
The Procond Elettronica MC-70 124438 treadmill board is malfunctioning, disrupting our production line. Urgent repair service needed immediately to resolve the issue and restore normal operations.

—> Purchase or Repair:
#Procond Elettronica by DOENLEN on 2009-07-05 09:32
BONJOUR,COULD YOU TELL ME THE PRICE FOR A NEW PART FOR A PROCOND ELETTRONICA PART NO 356066303-FOR SIEMENS REFRIGERATOR REF KI24L451FF/01?BEST REGARDSGUY DOENLEN

—> Purchase or Repair:
#Procond Elettronica by Ian thomas on 2011-05-19 18:02
Please could I purchase this part number from you 411312431How much Thanks Ian

—> Purchase or Repair:
#Procond Elettronica by Muller on 2013-10-11 14:42
Hello, we have a Procond Elettronica 356033305 47-90 circuit board that stopped working and we need repair information. Could you please provide guidance as soon as possible? Thank you.

—> Purchase or Repair:
#Procond Elettronica by pooDug on 2022-06-11 09:37
hallo ich bin POO :P ich wohne in IR. Das ist wohl thema? hmmmm , best regards for all :) POO I need to use eng or can GER?

—> Purchase or Repair:
#Procond Elettronica by lazkano on 2007-10-21 04:14
The Procond Elettronica MC-70 124438 treadmill controller on unit XYZ malfunctioned mid-shift. Please check and troubleshoot during the day shift.

—> Purchase or Repair:
#Procond Elettronica by Holographiccjr on 2022-01-03 08:52
multiplies (see also article

—> Purchase or Repair:

Contact Us

🚑Shop Location🛠️

Industrial Electronic Repair
124 Five Forks Dr PMB #208
King, NC 27021
🚑 Rush repair shipments only — no walk-ins.

📞Phone

1-336-969-0110

📦Mailing Address🚛

Industrial Electronic Repair
124 Five Forks Dr PMB #208
King, NC 27021
📦 Mailing Address (for invoices or shipped repairs)
No walk-ins accepted.