Procond Elettronica for Service call 1-336-969-0110 at Industrial Electronics Repair

Procond Elettronica Service & Repair Forum

Elevation motor is working properly, drive motor does not starts.There are 2 diods that are burn: DZ1 and DZ4 (in between the relay and what look like to be 2 ceramic resistors). There is an overheat area on PCB under these diods, but PCB still OK.Would you sell me just the diods?If not, how should I proceed?Thank you,Sergio - Ace Fitness Repair Inc

—> Purchase or Repair:

— Posted by Sergio Dratwa on 2007-11-13

Reply🗨️Ask a New Question Below❓

Recent Comments Search: "Procond Elettronica"

Procond Elettronica → MC-70 AW Rev - motor controller for Image 10.6Q ↗
Procond Elettronica → Procond Elettronica MC-70 124438 ↗
Procond Elettronica → Thanks ↗
Procond Elettronica → Procond Elettronica MC-70 MOTOR CONTROLLER ↗
Procond Elettronica → Procond Elettronica MC-70 141914 ↗
Procond Elettronica → Procond Elettronica my mc 70 board sent in for repair ↗
Procond Elettronica → Procond Elettronica Procond Elettronica MC-70 Repair-THANKS ↗
Procond Elettronica → AMF Paragon Timer ↗
Procond Elettronica → Procond Elettronica 45220051 675807501 ↗
Procond Elettronica → MC-70 AW.REV- PART#124438 ↗
Procond Elettronica → Procond Elettronica device to create PWM ↗
Procond Elettronica → MC-70 Motor Controller ↗
Procond Elettronica → Procond Elettronica MC-70 motor controller ↗

If you need your Procond Elettronica unit tested or repaired,
give us a call at 1-336-969-0110.
We offer free estimates and extended warranties on the work performed.
Shipping/Receiving:
Industrial Electronic Repair
145 Rockwell Place Ct
Tobaccoville, NC 27050
Phone: 1-336-969-0110

Recent 570 Comments

#Procond Elettronica by volta on 2006-12-08 14:16

Can the Procond Elettronica MC-70 124438 treadmill controller be repaired or purchased? I'm trying to check this off my to-do list. Thank you.

—> Purchase or Repair:

#Procond Elettronica by Daniel Butkievich on 2007-04-03 22:19

The Procond Elettronica MC-70 124438 treadmill controller is not working.

—> Purchase or Repair:

#Procond Elettronica by nguyentanvu on 2006-06-21 02:34

Procond Elettronica MC-70 124438 treadmill controller experiencing frequent power fluctuations, affecting production line efficiency. Urgent repair service needed to resolve issue

—> Purchase or Repair:

#Procond Elettronica by Quy P Nguyen on 2018-01-03 14:10

Procond 451523906

—> Purchase or Repair:

#Procond Elettronica by Dean Kralle on 2007-09-26 16:32

The Procond Elettronica MC-70 124438 treadmill controller unit is exhibiting unusual behavior during operation.

—> Purchase or Repair:

#Procond Elettronica by Faheem on 2007-04-18 14:00

The Procond Elettronica MC-70 124438 treadmill controller is not working as reported by someone in the shop.

—> Purchase or Repair:

#Procond Elettronica by Peter Cronje on 2006-06-23 00:34

The treadmill board on the Procond Elettronica MC-70 124438 is malfunctioning, disrupting the production line. Please expedite service to address and rectify the issue

—> Purchase or Repair:

#Procond Elettronica by Orukwo Amaechi on 2012-03-24 09:17

Please get me quote urgently for a Procond Ellectronica capacitor/switch of 0.25 micro farad with part no 411135901 for dish washing machine. We need it to replace the faulty one on our dish washing machine with the following specification:ELX Model: LS9PPN: 9CGX50502215EL: AC 400 V3 N AC 230V/3/50H…Purchase or Repair:

#Procond Elettronica by Muhammad usman on 2016-07-26 10:01

Dear Sir,Please helpot me hoe i repair this controller , its burnt due to 220V ,or please send me its technical data sheet where i can fix it Thanks

—> Purchase or Repair:

#Procond Elettronica by Ajardy on 2006-06-22 18:34

The Procond Elettronica MC-70 124438 treadmill controller is malfunctioning, affecting production. Urgently need repair service to address the issue to get the line back up and running ASAP.

—> Purchase or Repair:

#Procond Elettronica by feri setiawan on 2009-09-28 04:07

mesin cuci saya klo d nyalakan aliran listrik k mana2(semua body nyetrum).saya kasih tau service center nya daerah mana?

—> Purchase or Repair:

#Procond Elettronica by Charles on 2008-04-12 02:36

I have the same problem with mine. If I could get a value on these diodes, I could replace them. I need DZ2 and DZ4. I would like to have a schematic on this board.

—> Purchase or Repair:

#Procond Elettronica by burdette on 2007-04-04 04:19

Treadmill board on Procond Elettronica MC-70 124438 not powering up.

—> Purchase or Repair:

#Procond Elettronica by CHK AR CONDICIONADO LTDA on 2010-04-09 12:43

NEED BOARD MACHINE INSTALLED IN A CARRIER AIR CONDITIONER BRAND MODEL:GE ELECTRONIC PROCOND 356,068,908.YOU CAN DELIVER IN THE U.S. EVEN VIA FEDEX?OUR CUSTOMER WILL BE IN THE USA next week.PLS WAIT RETURN.CLÓVIS HIROSHI KUNII

—> Purchase or Repair:

#Procond Elettronica by Andrea on 2011-02-03 07:27

Buon giorno, sono nella necessità di reperire la sche elettronica della lavastoviglie Indesit che monta la scheda --GE PROCOND ELETTRONICA 356084601--- sull\'adesivo, oltre alla scritta procond elettrronica c\'è scritto: 23/01 ed i seguenti numeri: 452650801 21004683801avrei una certa urgenza di sap…Purchase or Repair:

#Procond Elettronica by sarwar alam on 2006-06-10 21:11

The Procond Elettronica MC-70 124438 treadmill controller is malfunctioning, leading to a disruption in the production line. We need immediate repair service to address this issue and resume operations swiftly.

—> Purchase or Repair:

#Procond Elettronica by TAI on 2007-07-12 05:28

Hello, I am reaching out on behalf of my client who has a Procond Elettronica MC-70 124438 treadmill board that needs repair. We have the part number and understand that it's related to the treadmill board. Could you please provide information on repair services available for this specific part? Tha…Purchase or Repair:

#Procond Elettronica by Riconda on 2007-03-20 16:01

Please provide information on whether Procond Elettronica MC-70 124438 treadmill controller is still supported or if replacement parts are available. Thank you.

—> Purchase or Repair:

#Procond Elettronica by johnny liu on 2007-10-18 17:42

I need DZ1 and DZ24 diodes. Both appear to be burned. Can I repair them?Thanks,Johnny

—> Purchase or Repair:

#Procond Elettronica by Ignasi López on 2019-12-10 07:35

My fridge don't work correctly. Continuesly put a message with E and whistle.The tecnic said me that that isn t a water problem, and he prove the motor and it works good.He said that the problem is is electronic system.I can t find a new electronic base.This base looks good and I m not sure of …Purchase or Repair:

#Procond Elettronica by Kosiecki on 2007-10-31 03:37

I'm sorry to hear that your Procond Elettronica MC-70 124438 treadmill controller is not functioning properly. It seems like there is an issue with the machine, but I'm uncertain about the exact problem. I recommend contacting a professional technician to diagnose and fix the problem for you.—> …Purchase or Repair:

#Procond Elettronica by Casella Vincenzo on 2013-04-05 22:57

Dear Sirs, I have a PROCOND ELETTRONICA card damaged.It is inside the yellow cover with these codesTYPE: 452604120COD ZANUSSI: 15248541/0220/240 Vac - 50 Hz T65 Ver. AWK 27/00The ELECTRONIC CARD inside damaged is marked:GE PROCOND ELETTRONICA 356084500The processor assembled on the card is marked SI…Purchase or Repair:

#Procond Elettronica by SETIABUDI on 2009-11-24 15:23

Electronic Module for washing machineHelloI would like to test this module, i don\'t know if it\'s working wellIs it possible to have a schematic or technical datasheet of this moduleRef = Type Procon :451511360Type E.Z: 13200353/2SW ver USA0020515/00 T70THANKS A LOTBEST REGARDS—> …Purchase or Repair:

#Procond Elettronica by hackle berry fin on 2008-10-16 05:32

please!!can you help me fix my raphaie sw-x7i don\'t know the value of dz1 and r3(zener diode and resistor)thanks!!

—> Purchase or Repair:

#Procond Elettronica by Guenat on 2011-08-22 14:52

Bonjour je recherche le module Procond elettronica 3560089039 pour un lave vaisselle FAGOR et le prixMerci

—> Purchase or Repair:

#Procond Elettronica by HURTADO Alain on 2019-05-09 15:31

Bonjour je cherche une carte GE Pocond ElecttronicaType P. 451510133 F : 6154Type E. 132156810SW Ver. W2C01450. 50/02Pourriez-vous m'indiquer comment puis- je en acheter une ou faire réparer la mienne ?

—> Purchase or Repair:

#Procond Elettronica by Legg on 2007-05-25 23:13

I'm reaching out to inquire about the support and availability of replacement parts for the Procond Elettronica MC-70 124438 treadmill controller. It is an older unit, and we are uncertain about the manufacturer. Please advise if this model is still supported or if replacement parts are available. T…Purchase or Repair:

#Procond Elettronica by ScottSak on 2005-12-28 05:12

The Procond Elettronica MC-70 124438 treadmill board is malfunctioning, causing a disruption in our production line. We need immediate repair service to address this issue

—> Purchase or Repair:

#Procond Elettronica by Jeff Spriggs on 2007-11-01 22:15

Can the Procond Elettronica MC-70 124438 treadmill controller be repaired or replaced? I'm trying to check this off my to-do list.

—> Purchase or Repair:

#Procond Elettronica by Angelo on 2006-06-20 15:32

The Procond Elettronica MC-70 124438 treadmill board is malfunctioning, affecting the production line. Urgent repair service needed to resolve the issue

—> Purchase or Repair:

#Procond Elettronica by Loyd Gerard on 2007-03-28 17:34

Can the Procond Elettronica MC-70 124438 treadmill controller be repaired or replaced? I'm working on crossing this off my to-do list.

—> Purchase or Repair:

#Procond Elettronica by Steve Arslan on 2007-09-24 13:06

Hello, I am interested in purchasing a Procond Elettronica MC-70 124438 treadmill controller. I wanted to inquire about the pricing and availability of this unit as I am looking to source one quickly. Thank you.

—> Purchase or Repair:

#Procond Elettronica by BOULIANNE on 2007-03-14 01:18

The Procond Elettronica MC-70 124438 treadmill controller in the warehouse is exhibiting abnormal behavior - it is not functioning as usual.

—> Purchase or Repair:

#Procond Elettronica by WILDKATcck on 2021-11-18 20:28

A handwritten book is a book

—> Purchase or Repair:

#Procond Elettronica by Brunet on 2018-01-04 09:08

HelloIs it possible to have a schematic or technical datasheet of this moduleProcond Elettronica 3560132009Thanks Martial Brunet

—> Purchase or Repair:

#Procond Elettronica by PICARD alexandre on 2010-01-13 22:34

hello , I search this product please:PROCONDELETTRONICA413.2712.00.10ìFthank you

—> Purchase or Repair:

#Procond Elettronica by lou broder on 2008-10-25 19:53

i am getting error message 21. any clue on what is wrong?

—> Purchase or Repair:

#Procond Elettronica by Monzur on 2007-10-10 17:40

The Procond Elettronica MC-70 124438 treadmill controller is not working and needs attention.

—> Purchase or Repair:

#Procond Elettronica by M.Beatriz Silveira MD on 2019-08-11 16:08

procono electtronica part 413 26 016I need this part to fix a machine

—> Purchase or Repair:

#Procond Elettronica by Helioui riadh on 2007-10-26 07:40

I have a Procond Elettronica MC-70 124438 treadmill display showing "ERR3." Please help troubleshoot.

—> Purchase or Repair:

#Procond Elettronica by Rounds on 2007-10-01 23:29

Experiencing issues with Procond Elettronica MC-70 124438 treadmill controller causing machine downtime. Need quick resolution before next shift. Please advise on the situation as soon as possible.

—> Purchase or Repair:

#Procond Elettronica by Rodriguez. on 2006-11-27 14:20

Please provide an update on the status of the repair for my Procond Elettronica MC-70 124438 treadmill board. It is still not functioning, and I require assistance immediately.

—> Purchase or Repair:

#Procond Elettronica by giles on 2005-12-09 22:47

The Procond Elettronica MC-70 124438 treadmill board in the warehouse is displaying unusual behavior - it is not functioning as it normally does.

—> Purchase or Repair:

#Procond Elettronica by Keith Haufler on 2006-05-19 22:42

I am having trouble with my powertread nordictrack treadmill PT 6.0 and have traced power into the controller. I checked the DC motor by hooking it up to a drill battery and it works fine. What part usually fails on these things? If I need to a replacement, what will it cost? Is it cheaper to send y…Purchase or Repair:

#Procond Elettronica by ARVIND on 2007-03-31 22:47

The Procond Elettronica MC-70 124438 treadmill board is not working.

—> Purchase or Repair:

#Procond Elettronica by Joann on 2007-01-10 03:11

Can the Procond Elettronica MC-70 124438 treadmill board be repaired or bought? I'm trying to check this off my to-do list.

—> Purchase or Repair:

#Procond Elettronica by Naresh on 2006-12-18 09:04

Looking for someone to repair my Procond Elettronica MC-70 124438 treadmill board. The unit is displaying error messages and not responding to any commands. Need assistance to get it operational again.

—> Purchase or Repair:

#Procond Elettronica by Giampiero Di Marco on 2005-12-21 07:47

The Procond Elettronica MC-70 motor controller is malfunctioning, causing a halt in production. Please address and rectify the issue urgently to minimize downtime on the line.

—> Purchase or Repair:

#Procond Elettronica by doinog on 2006-06-22 21:29

The Procond Elettronica MC-70 124438 treadmill controller is malfunctioning, causing disruptions to the production line. Urgent repair service is needed to resolve the issue

—> Purchase or Repair:

#Procond Elettronica by George Katinios on 2013-03-09 08:52

Dear Sirs,Is it possible to tell me the value of R82 resistor or send me the electronic schematics? Thank you in advance,Best wishesGeorge.

—> Purchase or Repair:

Contact Us

🚑Shop Location🛠️

Industrial Electronic Repair
145 Rockwell Place Ct
Tobaccoville, NC 27050
🚑 Rush repair shipments only — no walk-ins.

📞Phone

📦Mailing Address🚛

Industrial Electronic Repair
931-E S. Main St #204
Kernersville, NC 27284
📦 Mailing Address (for invoices or shipped repairs)
No walk-ins accepted.