Robotool Service & Repair Forum

Hi,We have a Robotool CVM1 that we are in the process of retrofitting. Could you give me the info on the following plug connections: J43, J518,J515 J52. We are converting to PC4CNC. The machine was working when we pulled the boards so if there is anyone in the market for them let me know. Any help in this matter would be greatly appreciated.Thanks in Advance Carl

— Posted by Carl Angell on 2015-04-14

Reply🗨️Ask a New Question Below❓


Recent Comments Search: "Robotool"

If you need your Robotool unit tested or repaired,
give us a call at 1-336-969-0110.
Estimates are free with an approved repair. Declined or unrepairable units are subject to a $75 evaluation, handling, and standard return-shipping fee. Extended warranties may be available.
Shipping/Receiving:
Industrial Electronic Repair
124 Five Forks Dr PMB #208
King, NC 27021
Phone: 1-336-969-0110

Recent 7 Comments

#Robotool by Bob Challes on 2011-08-04 00:51
Cannot Autohome X Axis switch is open
➡️ Reply
#Robotool by tom burgmeier on 2007-08-16 15:45
I have a cvm-1 they offered a upgrade with a new pc paised system for $5,000.00 cookbook change up. Do you have such a system you offer? I didn\'t like the CPM disk drive and only 2-1/2 axis contouring.please fax,email, or calltom burgmeierlibety machine & tool7908 ontario avecicero ny 13039fax 315/…...
Show More
➡️ Reply
#Robotool by AL on 2007-07-31 21:06
It appears that your himem.sys file is corrupted or missing.config.sys line 2 error is probably calling for this file.Open the file with notepad.exe and see. (or boot up w DOS floppy. type: Edit config.sys or open config.sys)if so, simply copying the himem.sys from your DOS disk could fix the proble…...
Show More
➡️ Reply
#Robotool by Carl Angell on 2015-04-14 18:18
Hi,We have a Robotool CVM1 that we are in the process of retrofitting. Could you give me the info on the following plug connections: J43, J518,J515 J52. We are converting to PC4CNC. The machine was working when we pulled the boards so if there is anyone in the market for them let me know. Any help i…...
Show More
➡️ Reply
#Robotool by Charles Park on 2007-07-28 19:56
Have a problem with operating system, here is the error that I am getting when trying to boot up system.Is there any way to get a copy of the master disk?Or is this a hardware problem, like mabey the mother board is goneBad or missing \\dos\\ himem.sysError in config.sys line2Hma not available: load…...
Show More
➡️ Reply
#Robotool by karl rezmann on 2005-11-18 02:43
faster pc based control available ?std 1.44 floppyeasy edit on std pcetc
➡️ Reply
#Robotool by Klaus on 2015-10-07 20:33
Looking looking for someone that can troubleshoot the control box for the Roto tool we can send PCBoards to them to do bug in the main control since we have no idea what\'s wrong with it it drilled so many holes and goes to one hole again and stops the whole that is already drilled.Are you capable o…...
Show More
➡️ Reply

Contact Us

🚑Shop Location🛠️

Industrial Electronic Repair
124 Five Forks Dr PMB #208
King, NC 27021
🚑 Rush repair shipments only — no walk-ins.

📞Phone

1-336-969-0110

📦Mailing Address🚛

Industrial Electronic Repair
124 Five Forks Dr PMB #208
King, NC 27021
📦 Mailing Address (for invoices or shipped repairs)
No walk-ins accepted.