Scofima Service & Repair Forum

Hello Sir. we are ex Scofima System we have all schematic pcb etc of Scofima System, if will be usefull to repair any unit or have it new don\'t hesitate to contact us,Best Regards,Safco Systems s.r.l.

— Posted by Safco Systems s.r.l. on 2010-11-04

Reply🗨️Ask a New Question Below❓


Recent Comments Search: "Scofima"

If you need your Scofima unit tested or repaired,
give us a call at 1-336-969-0110.
Estimates are free with an approved repair. Declined or unrepairable units are subject to a $75 evaluation, handling, and standard return-shipping fee. Extended warranties may be available.
Shipping/Receiving:
Industrial Electronic Repair
124 Five Forks Dr PMB #208
King, NC 27021
Phone: 1-336-969-0110

Recent 8 Comments

#Scofima by David Jones on 2010-10-13 18:40
How can I get a drawing that will show me the proper wiring of this unit. I Have a control that will not light up. I have no way of knowing which terminal is the incoming 24vdc feed, so I can\'t determine if the control is bad or just not getting power. I do have 24vdc on terminal # 14.Thank YouDavi…...
Show More
➡️ Reply
#Scofima by Jan Czarnota on 2010-10-14 10:56
Could I get the electrical diagram of board: SM48 ?This is Thyrystor control board.With kind regardsJan Czarnota
➡️ Reply
#Scofima by M.Kaviani nezhad on 2009-04-09 05:22
Hello dear chairmanwould you please introduce only the name of software for programing welding machine : IP3/S470 ?With best RegardsNovin Andisheh Kavian
➡️ Reply
#Scofima by Emil on 2009-02-23 11:04
I have 2 spotwelders with scofima sm219/a controlers.None of these welders whants to fire. The sequence is right but no welding ocurs. led 16 is also flashing ? Can u help me
➡️ Reply
#Scofima by Safco Systems s.r.l. on 2010-11-04 16:44
when led 16 is flashing means \"current off\" no weld, it is sufficent to push \"+\" key to switch in current on
➡️ Reply
#Scofima by Safco Systems s.r.l. on 2010-11-04 16:39
Hello Sir. we are ex Scofima System we have all schematic pcb etc of Scofima System, if will be usefull to repair any unit or have it new don\'t hesitate to contact us,Best Regards,Safco Systems s.r.l.
➡️ Reply
#Scofima by Howard Neal on 2006-07-11 13:29
Dear sirDo you recognise this board and do you have a schematic for it because some clown has cut all the wires and we need to reconnect it??Regards, Howard Neal, Burner Plus services, Cyprus.
➡️ Reply
#Scofima by doquy on 2020-04-16 11:27
I have a circuit board of Scofima System SM48 but there is no function of the pins! Can you send me the connection method of the board?
➡️ Reply

Contact Us

🚑Shop Location🛠️

Industrial Electronic Repair
124 Five Forks Dr PMB #208
King, NC 27021
🚑 Rush repair shipments only — no walk-ins.

📞Phone

1-336-969-0110

📦Mailing Address🚛

Industrial Electronic Repair
124 Five Forks Dr PMB #208
King, NC 27021
📦 Mailing Address (for invoices or shipped repairs)
No walk-ins accepted.