Sitra Automazione Service & Repair Forum

I´m repairing a VSD6 ampli-spindle witch have a problem in brake system.There are two resistances R3 and R4 that I don´t know the value. Can you help me?Ampli-spindle: Sitra VSD 6 sn: 98VSD6252PCB of brake: Sitra 1993-FR.Thanks in advance.Melo

—> Purchase or Repair:

Reply🗨️Ask a New Question Below❓

• Sitra Automazione → Sitra Automazione Digit 165 C1 error ↗
• Sitra Automazione → Sitra Automazione Sitra HF converter model CP 800 ↗
• Sitra Automazione → Sitra Automazione VSD 10 ↗
• Sitra Automazione → Spindle drive with display L20 ↗
• Sitra Automazione → Sitra ↗
• Sitra Automazione → List errors ↗
• Sitra Automazione → Sitra Automazione Spindle wont run ↗
• Sitra Automazione → Sitra Automazione Sitra VSD6 ↗
• Sitra Automazione → Sitra Automazione VSH4 ↗

Recent 9 Comments

#Sitra Automazione by Krzysztof Pachucki on 2012-05-09 19:40

Hello,we need list of errors on Sitra HF converter model CP 800. Can you please send usBest RegardsKrzysztof PachuckiMaintenance EngineerTel: +48 33 499 3731Mobile: 0 785 009 517Fax: +48 33 499 3501PachuckiKrzysztof@eaton.comwww.eaton.comVehicle Group EMEAEaton Automotive Systems Sp. z o.o.Ul. Rudaw…Purchase or Repair: ...Hello,we need list of errors on Sitra HF converter model CP 800. Can you please send usBest RegardsKrzysztof PachuckiMaintenance EngineerTel: +48 33 499 3731Mobile: 0 785 009 517Fax: +48 33 499 3501PachuckiKrzysztof@eaton.comwww.eaton.comVehicle Group EMEAEaton Automotive Systems Sp. z o.o.Ul. Rudawka 8343-382 Bielsko-Bia³aPolandwww.eaton.com

—> Purchase or Repair:
Show More

➡️ Reply

#Sitra Automazione by R S Raghavan on 2012-02-02 11:50

Dear Sir,We have one new CP 800 converter with us. On trying to install this unit we found the parameters were missing in the system. When we tried uploading the parameters through the serial interface of the CP 800 we found the system had no firm ware loaded. Can you please send us the firmware 1-9…Purchase or Repair: ...Dear Sir,We have one new CP 800 converter with us. On trying to install this unit we found the parameters were missing in the system. When we tried uploading the parameters through the serial interface of the CP 800 we found the system had no firm ware loaded. Can you please send us the firmware 1-9999 version and procedure for uploading the same. In case there is any cost for this please let us know.RegardsRaghavan

—> Purchase or Repair:
Show More

➡️ Reply

#Sitra Automazione by Jim Aarssen on 2008-09-23 16:48

Spindle drive VSH tipo vsh6 01VSH6356 I have a problem with this drive and hope you can help me.The display shows L20 and also the cnc control says the drive is not ready.Could you tell me if i could get the manual for this drive that would list all the alarms. Thank You Jim Aarssen email ak2mainten…Purchase or Repair: ...Spindle drive VSH tipo vsh6 01VSH6356 I have a problem with this drive and hope you can help me.The display shows L20 and also the cnc control says the drive is not ready.Could you tell me if i could get the manual for this drive that would list all the alarms. Thank You Jim Aarssen email ak2maintenance1@aarkel.com

—> Purchase or Repair:
Show More

➡️ Reply

#Sitra Automazione by Mike Haverkamp on 2006-01-14 17:54

Sitra Automazione VSD 6Drive is showing a L 08 on the digital display before we try to start the spindle. When we try to start the spindle the drive shuts off & goes black. Any suggestions? I need help, my milling machine is down & I have work backed up for it.Thank you for your attention to this ma…Purchase or Repair: ...Sitra Automazione VSD 6Drive is showing a L 08 on the digital display before we try to start the spindle. When we try to start the spindle the drive shuts off & goes black. Any suggestions? I need help, my milling machine is down & I have work backed up for it.Thank you for your attention to this matter.Mike Haverkamp

—> Purchase or Repair:
Show More

➡️ Reply

#Sitra Automazione by Pete Gallagher on 2007-09-20 09:29

The above drive is fitted to a Mecof 5 axis milling machine and controls the high speed finishing head.This is the 2nd occasion that the 4 large capacitors, thyristors, power resistors and varistors on the input side of the drive have failed (exploded), welding the main contactor closed blowing 125 …Purchase or Repair: ...The above drive is fitted to a Mecof 5 axis milling machine and controls the high speed finishing head.This is the 2nd occasion that the 4 large capacitors, thyristors, power resistors and varistors on the input side of the drive have failed (exploded), welding the main contactor closed blowing 125 Amp fuses.Following the first repair the machine ran for approx 3 weeks but the same fault has now re occured.After the 1st occasion we thought the input filter may be at fault so we disconnected it and ran the machine without it but now we know this is not the problem.We have replaced all the faulty components but have not tried to run the drive until we hear from you on the issue.We have no manuals or information on the drive to assist us in fault finding or repairs.

—> Purchase or Repair:
Show More

➡️ Reply