Sterl-Tronic Service & Repair Forum

The company that made the Sterl-tronic control is called Sterling Controls and thats in wisconsin. They have a web site , you can find it if you search Sterling Controls. Their technical library isant availble on line You\'ll have to call them. Their number is on their web site.

— Posted by Dave on 2007-10-18

Reply🗨️Ask a New Question Below❓

If you need your Sterl-Tronic unit tested or repaired,
give us a call at 1-336-969-0110.
We offer fair estimates and extended warranties on the work performed.
Shipping/Receiving:
Industrial Electronic Repair
145 Rockwell Place Ct
Tobaccoville, NC 27050
Phone: 1-336-969-0110

Recent 9 Comments

#Sterl-Tronic by MOHAMMED ALI on 2006-07-12 11:55
Dear Sir,We have a STERL-TRONIC oil heater unit and we have a problem in the heating of this machine so we need the manual and troubleshooting if available or advise us in manufacturer that can help.Serial#: 95L5186.Model#: G9026-J1.380V – 3ph- 60Hz- 58AELEM DIG#: d682-82928.
➡️ Reply
#Sterl-Tronic by HENNIE TERBLANCHE on 2007-05-07 07:06
We have a problem with the control unit, the controller does not come on it keeps on flahsing on the display.This fault occured after the main heater element fuses blew, because it went down to earth. the supply to the controller is constant 120Vac.RegardsHennie
➡️ Reply
#Sterl-Tronic by Dave on 2007-10-18 15:33
The company that made the Sterl-tronic control is called Sterling Controls and thats in wisconsin. They have a web site , you can find it if you search Sterling Controls. Their technical library isant availble on line You\'ll have to call them. Their number is on their web site.
➡️ Reply
#Sterl-Tronic by Dan Hughes on 2008-06-25 14:16
Please call me in regards to this unit. I have some questions concerning the one that I have just purchased. Thanks
➡️ Reply
#Sterl-Tronic by Don Eagan on 2009-05-12 19:06
Hi,We have three old Sterl-Tronic Model X6410-AX Temperature Controllers for our rubber injection machines. By chance, do you know where I can get electrical schematics for these machines? Please respond to this e-mail so I know if I have to continue my search.Thanks!!Don
➡️ Reply
#Sterl-Tronic by Arun RS Nair on 2010-09-18 05:20
SirWe have a srerl tronic oil heater calendering machine of Fairview make with the Sr No.SN 290/25 G and the Type 2S/S GAP.Can you please advise us which type of oil we have to use with the machine?
➡️ Reply
#Sterl-Tronic by Frankie Allen on 2010-12-14 19:52
We are trying to locate a heater element for a Sterl-Tronic .Model: M8412-A SN#66367460vac, 3 phase, 12 amp9000 watt heater.
➡️ Reply
#Sterl-Tronic by Jeremy Roth on 2011-11-17 15:21
We have a STERL-TRONIC oil heater unit and we are haveing a problen with getting it to heat up. I have been through everything electronicly and all looks fine. So i need a manual to possibly be able to trouble shoot the problem. If you could help me out with this or know of someone who can that woul...
Show More
➡️ Reply
#Sterl-Tronic by Mohammed Hosawi on 2011-12-18 12:09
Dear Sir,We have a STERL-TRONIC oil heater unit and we have a problem in the heating of this machine so we need the manual and troubleshooting if available or advise us in manufacturer that can help.Serial#:95K5151.Model#: G9026-J1.230V – 3ph- 60Hz- 58AELEM DIG#: d682-82928.
➡️ Reply

Contact Us

🚑Shop Location🛠️

Industrial Electronic Repair
145 Rockwell Place Ct
Tobaccoville, NC 27050
🚑 Rush repair shipments only — no walk-ins.

📞Phone

1-336-969-0110

📦Mailing Address🚛

Industrial Electronic Repair
931-E S. Main St #204
Kernersville, NC 27284
📦 Mailing Address (for invoices or shipped repairs)
No walk-ins accepted.