Unimac Service & Repair Forum

looking for a elect motor for unimac um50p3 washer, unimac p/n 1039266480. voltage 208-240 hz60 wire 4 amps 13 5.5 hp .65kw 530 rpm motor model cp132 c/8-12-2t-4411.please advise price and deliverythanks

— Posted by charles onstead on 2016-02-25

Reply🗨️Ask a New Question Below❓


Recent Comments Search: "Unimac"

If you need your Unimac unit tested or repaired,
give us a call at 1-336-969-0110.
We offer free estimates and extended warranties on the work performed.
Shipping/Receiving:
Industrial Electronic Repair
145 Rockwell Place Ct
Tobaccoville, NC 27050
Phone: 1-336-969-0110

Recent 10 Comments

#Unimac by Ramesh Ragha on 2008-06-26 20:54
I\'m looking for a wash motor for UW60P30, slightly used or new, please e-mail me on a price. Thank you.
➡️ Reply
#Unimac by BEVERLY Maxwell Newirth on 2008-02-05 16:49
I NEED KEY FOR UNIMAC WASHER KEY #3800
➡️ Reply
#Unimac by Eddie Thomas on 2008-08-19 18:22
Where is the nearest service shop located. Need to know the cost for maintenance and repair.
➡️ Reply
#Unimac by bipin v patel on 2009-09-01 15:31
WASHER IS NOTY WORKING,FUSE F21 WAS BAD,WHEN WE CHANGE THE FUSE ITS BLOW OUT AGAIN,DURING THE WASH CYCLE.
➡️ Reply
#Unimac by bharat patel on 2007-10-30 00:47
i have a uni mac washer need to repair,not dran porporly
➡️ Reply
#Unimac by Viktor on 2008-03-30 13:38
Gents, I need P/N for belt for UNIMAC Dryer UB075 E (big one)Thanks
➡️ Reply
#Unimac by JAY PATEL on 2009-01-17 18:06
WE NEED A REASONABLY PRICED GOOD USED OR NEW CYLINDER AND TRUNNION ASSEMBLY FOR UNIMAC DRYER MODEL # DTB75CGK ALSO CAN USE INNER AND OUTER TRUNNION BEARINGS FOR SAME MECHINE.
➡️ Reply
#Unimac by charles onstead on 2016-02-25 16:30
looking for a elect motor for unimac um50p3 washer, unimac p/n 1039266480. voltage 208-240 hz60 wire 4 amps 13 5.5 hp .65kw 530 rpm motor model cp132 c/8-12-2t-4411.please advise price and deliverythanks
➡️ Reply
#Unimac by George Park on 2008-09-27 18:05
50lb unimac invatar control system.
➡️ Reply
#Unimac by Nizuyir on 2007-11-06 03:24
I removed my unimac washer drum for replacement of the bearings in the trunnion.There are two V-rings installed. The outside diameter (OD) is 8.5 inches, and the inside diameter (ID) is 5 inches and thickness is 0.5 inch. I am unable to get the part numbers or suppliers for these items.Could anyone …...
Show More
➡️ Reply

Contact Us

🚑Shop Location🛠️

Industrial Electronic Repair
145 Rockwell Place Ct
Tobaccoville, NC 27050
🚑 Rush repair shipments only — no walk-ins.

📞Phone

1-336-969-0110

📦Mailing Address🚛

Industrial Electronic Repair
931-E S. Main St #204
Kernersville, NC 27284
📦 Mailing Address (for invoices or shipped repairs)
No walk-ins accepted.