Westamp Service & Repair Forum

Good morming, we are 2 Mechatronic Engineer, we write you becasuse we need a schematic diagram of one of your DC drives in order to retrofit a Bridgeport Mill Machine with Anilam Crusader II panel. Any other information will be gladly recievedThe driver is: Westamp Inc, Assy 30059.We would be very pleased if you can help us.Best regards.Andres

— Posted by Andres Felipe Marmol Velez on 2007-11-30

Reply🗨️Ask a New Question Below❓

If you need your Westamp unit tested or repaired,
give us a call at 1-336-969-0110.
We offer fair estimates and extended warranties on the work performed.
Shipping/Receiving:
Industrial Electronic Repair
145 Rockwell Place Ct
Tobaccoville, NC 27050
Phone: 1-336-969-0110

Recent 12 Comments

#Westamp by Syed Pervez Ali on 2006-02-15 07:45
I have one machine vertical mill Avon with crusader II anilam opertating panel.it is not in working position before to run it I want to check it servo drive cards with servo motors , I am 30 years experienced man of working in electronics and industerial equipments.these card are in very good condit...
Show More
➡️ Reply
#Westamp by SAUL on 2006-08-29 23:48
I NEED THE DIAGRAM OF CONECTION OF THE WESTAMP CARD AW 29947TO TEST THE CARD AND THE SIGNAL IS REQUIRE TO WORKTENKS
➡️ Reply
#Westamp by Adan Caldera on 2006-09-07 19:00
Hi, I need to kow what kind of transistor its 29794 because I have one servo drive that have this transistor damage its in short.Can you help me whit this pease,Thanks.
➡️ Reply
#Westamp by niaraki on 2007-05-28 07:07
dear sirswe have a colchester/master 600cnc lathe.its control system is crusader ii l anilam microprocesser control system.drive is indramat 3trm2.we bought it as a used mashie. control system dosent work.would you please help us how we can get its troublshooting plan and programming and operating i...
Show More
➡️ Reply
#Westamp by niaraki on 2007-05-28 07:09
dear sirswe have a colchester/master 600cnc lathe.its control system is crusader ii l anilam microprocesser control system.drive is indramat 3trm2.we bought it as a used mashie. control system dosent work.would you please help us how we can get its troublshooting plan and programming and operating i...
Show More
➡️ Reply
#Westamp by Andres Felipe Marmol Velez on 2007-11-30 14:32
Good morming, we are 2 Mechatronic Engineer, we write you becasuse we need a schematic diagram of one of your DC drives in order to retrofit a Bridgeport Mill Machine with Anilam Crusader II panel. Any other information will be gladly recievedThe driver is: Westamp Inc, Assy 30059.We would be very p...
Show More
➡️ Reply
#Westamp by Harold Godwin on 2008-02-21 15:55
I have the same control and am in need of schematic for westamp drive so I can determine whether I have a drive problem or control problem
➡️ Reply
#Westamp - UltraDrive by Matt Saponara on 2008-06-13 13:59
We have an older Campbell CNC Router which has a westamp drive unit. Westamp Ser. # 756; Mod. # A7214-17F-003(041886). We cant get drive cards anymore and the repaired ones are not lasting. Can we upgrade to a newer drive unit?Matt SaponaraMaintenance ManagerHunter Marine386-462-3658
➡️ Reply
#Westamp by quocphan on 2008-10-08 14:10
order chip TOSHIBA TF1204 QTY:40
➡️ Reply
#Westamp by miguel rangel on 2009-04-30 01:53
I have a milling machine, eqquiped with servocontrol, it has two cards with label WESTAMP 30059-.one of them have some burned components (diodes, resistors)I don`t have any information of the circuit cards.can you help me to obtain schematics or send me information about repair service?thanks
➡️ Reply
#Westamp by GARY LEBLANC on 2009-11-02 17:44
Hello,I am looking for the following circuit/test board:Westamp Inc. Assy 34235 Circuit/Test Board or Assy 34233 Rev. AThank you
➡️ Reply
#Westamp by RITA-DU on 2010-10-20 06:05
30060-116servometer drive board£¬made by Westamp £¬ 1PCSused for NV10-160
➡️ Reply

Contact Us

🚑Shop Location🛠️

Industrial Electronic Repair
145 Rockwell Place Ct
Tobaccoville, NC 27050
🚑 Rush repair shipments only — no walk-ins.

📞Phone

1-336-969-0110

📦Mailing Address🚛

Industrial Electronic Repair
931-E S. Main St #204
Kernersville, NC 27284
📦 Mailing Address (for invoices or shipped repairs)
No walk-ins accepted.